DV Video Cassette Recorder Instruction Manual

ManualsBrandsJVC ManualsMP3 PlayerBR-DV3000U

RECORDING

–

Audio dubbing

–

For tapes recorded in the 32kHz audio mode, audio dubbing can be performed on the CH3 and

CH4 channel after the recording. (After-recording)

Notes

• For tapes recorded in the 48kHz audio mode, audio dubbing cannot be performed.

• Audio dubbing cannot be performed for DV input signals.

A.DUB

F.REV

INDEX– INDEX+

PLAY

STOP

REMOTE CONTROL UNIT

RM-G3000

REW FF

PAU SE

REC

F.A DV

1. 4.

PLAY

button

2. 3.

PAUSE button

STOP

button

A.DUB

button

Mini

PROFESSIONAL

SET

MENIU

EJECT

REC PLAY

PAU SE

REW

STOP

DVCAM NTSC

PAL

REC INH.

CH-1/3

CH-2/4

BR-DV3000

A.DUB

OPERATE

INPUT SEL.REMOTE SEL.

MIC

SERIAL

WIRELESS

9PIN

LINE

Y/C

2. 3.

PAUSE

button

STOP buttonINPUT SEL switch

1. 4.

PLAY button

A.DUB button

MIC

terminal

Connection

Audio dubbing sounds are input from the AUDIO IN

terminal on the rear panel or the MIC terminal on

the front panel. MIC terminal prevail over the AU-

DIO IN terminal.

Setting

• Set the AUDIO item of the AUDIO/VIDEO menu

to 32k.

• Do not set the INPUT SEL switch on the front

panel to DV.

Operation

Press the PLAY button to play the tape.

At the position where you want to au-

dio dub, press the PAUSE button.

¥ The unit goes into the STILL mode.

Hold down the PAUSE button and press

the A.DUB button.

¥ The unit goes into the audio dubbing pause

mode.

Press the PLAY button.

¥ Audio dubbing begins. Audio signals are

recorded on the CH3 and CH4 channel.

䡵 To stop audio dubbing temporarily, press

the PAUSE button.

To end audio dubbing, press the STOP

button.

Memo

• During audio dubbing, if the tape comes to a

part recorded in a non dubbing-feasible mode

(such as LP mode or 48kHz audio mode), the

VTR will enter the STOP mode. When this hap-

pens, high-volume noise from the DV output

will occur. Hence, before audio-dubbing, please

check the recording mode of the tape.

• In the case that a microphone is connected to

the MIC terminal, sound output from this ter-

minal will be recorded. In the absence of MIC

input, signals from the CH1/3, CH2/4 AUDIO

IN terminal on the rear panel will be recorded.

• When audio dubbing cannot be performed, an

alarm message will be displayed on the moni-

tor. (

☞

Page 23)

• Audio dubbing PAUSE cannot be executed di-

rectly in the STOP mode. Please execute it in

the STILL mode.

During audio dubbing pause, sound from the

CH3/CH4 channel is output via the monitor but

sound output from the DV terminal is not pos-

sible.

• If audio dubbing is repeated on a short section

of the tape, noise may occur for an instant when

the section is played.

• During audio dubbing, noise may be produced

on the playback video or EE sound but the re-

cording is normal.

• The playback sound of CH1/2 cannot be re-

corded on CH3/4 (sound on sound).

• During backspace operation of audio dubbing,

audio dubbing cannot be performed on unre-

corded parts.

• When audio dubbing is performed on tapes re-

corded on other devices, it may not record cor-

rectly. Please record with this unit before per-

forming audio dubbing.

RECORDING

–

Recording method –

Main unit

Remote controller

Mini

PROFESSIONAL

SET

MENIU

EJECT

REC PLAY

PAUSE

REW

STOP

DVCAM NTSC

PAL

REC INH.

CH-1/3

CH-2/4

BR-DV3000

A.DUB

OPERATE

INPUT SEL.REMOTE SEL.

MIC

SERIAL

WIRELESS

9PIN

LINE

Y/C

PAUSE

button

STOP button

2. 4.

PLAY

button

REC

button

A.DUB

F.REV

INDEX– INDEX+

PLAY

STOP

REMOTE CONTROL UNIT

RM-G3000

REW FF

PAUSE

REC

F.A DV

2. 4.

PLAY

button

REC button

STOP

button

PAUSE button

Memo

• If recording has been

paused for an extended pe-

riod of time, the unit will au-

tomatically go into the

STOP mode to protect the

tape. The time period after

the lapse of which the unit

will enter the STOP mode

can be configured via the

LONG PAUSE TIME item of

the SYSTEM (1/2) menu.

• This unit cannot perform

editing functions.

Load the cassette.

• Before loading the cassette, please check that the rear slide of

the cassette is pushed to REC.

¥ The Main unit is powered on.

Start recording.

• Hold down the REC button and press the PLAY button.

Pause recording.

• Press the PAUSE button.

Resume recording.

• Press the PLAY button.

Stop recording.

• Press the STOP button.

When the INDEX WRITE item of the SYSTEM (1/2) menu is

set as ON, an index signal is recorded at the starting position

of recording.

In the PLAYBACK mode, the position where the index signal is

recorded can be detected. (Index search)

䡵 During recording, please press the REC button to record

the index signal.

* Please allow at least an interval of 1 minute between recording of

index signals.

Recording of index signals after tape recording is not possible.

Recording index signals

Memo

If recording is executed right

after the RECORDING

PAUSE state, index signals

will not be recorded.