DV Video Cassette Recorder Instruction Manual

15
DV IN/OUT
AUDIO VIDEO
LINE
Y/C
CH 1/3 CH 2/4
INOUT
REMOTE
SERIAL
9PIN
NTSC/PAL
NTSC PAL
DC12V
!65
87
9
0
5
[VIDEO Y/C IN] Video Y/C input
terminal (4P)
This is the input terminal for YC separate video signals.
● To input video signals from this terminal,
set the [INPUT SEL.] switch on the front
panel to “Y/C”.
● When Wide discriminating signals are in-
put, ID signals for Wide discriminating sig-
nals are recorded.
6
[VIDEO LINE IN] Video line input
terminal (RCA)
This is the input terminal for composite video
signals.
● To input video signals from this terminal,
set the [INPUT SEL.] switch on the front
panel to “LINE”.
7
[VIDEO Y/C OUT] Video Y/C output
terminal (4P)
This is the output terminal for YC separate video
signals.
8
[VIDEO LINE OUT] Video line out-
put terminal (RCA)
This is the output terminal for composite video signals.
When tapes recorded with Wide discriminating
signals are played, ID signals for discriminating
signals are output.
Memo
● Besides video signals, the following signals from
the [VIDEO Y/C OUT] terminal and [VIDEO LINE
OUT] terminal are displayed on-screen.
• Menu screen signals
• Character display of date, time or operation
modes (Status screen)
By pressing the DISPLAY button on the wireless
remote controller or by setting the DISPLAY item in
the DISPLAY menu, the user can choose to turn
the status display on/off.
● The SETUP item of the AUDIO/VIDEO menu can
be set to determine whether setup will be added to
the signals of [VIDEO Y/C OUT] terminal and
[VIDEO LINE OUT] terminal. (NTSC only).
9
[AUDIO IN] Audio input terminal
(RCA2)
This is the audio signal (analogue) input termi-
nal.
For audio dubbing, sounds from the CH1/3 ter-
minal are recorded on the CH3 channel while
those from the CH2/4 channel are recorded on
the CH4 channel.
Memo
When the MIC terminal on the front panel is connected
to a microphone, sounds from this terminal will not
be recorded.
0
[AUDIO OUT] Audio output terminal
(RCA2)
This is the audio signal (analogue) output ter-
minal.
Memo
● The audio channel to play back tapes recorded in
the 32k mode can be selected with the OUT SE-
LECT button on the wireless remote controller or
by setting the AUDIO OUT SEL. item of the AU-
DIO/VIDEO menu.
● The output level of the playback audio can be se-
lected with the OUT LEVEL button of the wireless
remote controller or by setting the AUDIO OUT
LEVEL item of the AUDIO/VIDEO menu (NORMAL
or ATT).
!
[DV IN/OUT] DV input/output termi-
nal
This is the input/output terminal for digital sig-
nals of IEEE1394 standard. It is connected to
video devices with DV terminals.
● To input signals from this terminal, please set
the [INPUT SEL.] switch on the front panel to
“DV”.
● Signals from this terminal are output regard-
less of the INPUT SEL. switch setting.
14
NAMES AND FUNCTIONS
OF VARIOUS PARTS
–
Rear panel
–
1
DC power input terminal (2P)
This is used for DC12V input. It connects the
DC power cord of the provided AC adapter.
Memo
● When power is supplied to this terminal, the
OPERATE indicator located at the front panel
lights up. (The LED lights up red when the
OPERATE indicator is OFF.)
● Setting this unit to OPERATE ON, OPER-
ATE OFF or PLAY mode when the power is
supplied to this terminal can be done by mak-
ing the appropriate selections from the DC
IN MODE item in the SYSTEM menu.
2
[NTSC/PAL] NTSC/PAL signal se-
lection switch
Use this switch to select NTSC or PAL as the
signal system. Use it to make a selection when
composite video signals or YC separate video
signals are input.
NTSC : Use this setting for NTSC signal input.
The NTSC indicator on the front panel
lights up.
PAL : Use this setting for PAL signal input.
The PAL indicator on the front panel
lights up.
Memo
● For playback or DV signal input, signals are
determined automatically and not affected by
the status of this switch.
● Please turn the unit to OPERATE OFF be-
fore using this switch. If switching is performed
when the VTR is in the OPERATE ON mode,
the VTR will automatically go into the OFF
mode before engaging the ON mode.
● It cannot be used for NTSC/PAL conversion.
DV IN/OUT
AUDIO VIDEO
LINE
Y/C
CH 1/3 CH 2/4
INOUT
REMOTE
SERIAL
9PIN
NTSC/PAL
NTSC PAL
DC12V
4
3
2
1
3
[SERIAL REMOTE] serial remote
terminal (mini jack)
Connect this terminal to the serial remote con-
troller RM-G30, which is available separately.
To control this unit via this terminal, please set
it up as follows.
● Set the REMOTE item of the REMOTE
menu to ON.
● Set the [REMOTE SEL.] switch on the front
panel to “SERIAL”.
Memo
To use this terminal as the FOOT switch input
terminal, please set the FOOTSW item of the
REMOTE (2/2) menu.
☞
Page 60
4
[9 PIN REMOTE] 9-pin remote ter-
minal (D-SUB)
Use this terminal to connect to the RS-422A-
compatible editing remote controller (RM-G820).
Please use this unit as a player. To control this
unit with this terminal, please set it up as fol-
lows:
● Set the REMOTE item of the REMOTE
menu to ON.
● Set the [REMOTE SEL.] switch on the front
panel to “9 PIN”.