Operation Manual

33
Additional Information
Learning More about This System
Connections
(see pages 3 to 5)
• Make sure the antenna conductors do not touch any other
terminals, connecting cords or the power cord. Also, keep
the antennas away from metallic parts of the System,
connecting cords, and the AC power cord. This could cause
poor reception.
• Use only speakers with the same speaker impedance as
indicated by the speaker terminals on the rear of the System.
• The speakers are magnetically shielded to avoid color
distortions on TVs. However, if not installed properly, it
may cause color distortions. So, pay attention to the
following when installing the speakers.
– When placing the speakers near a TV set, turn off the
TV’s main power switch or unplug it before installing the
speakers.
Then wait at least 30 minutes before turning on the TV’s
main power switch again.
– Some TVs may still be affected even though you have
followed the above instructions. If this happens, move
the speakers away from the TV.
Daily Operations—Playback
(see pages 7 to 10)
Listening to the Radio:
• If you store a new station into an occupied preset number,
the previously stored station in that number will be erased.
• When you unplug the AC power cord or if a power failure
occurs, the preset stations will be erased in a few days. If
this happens, preset the stations again.
Listening to the TV Sound:
• When you use this function, connect the System and TV
with the Scart cable.
Playing Back a Disc/File:
• When you change the source to DVD/CD or USB
MEMORY, it may take a while to activate the source.
• The following functions cannot be used for the files in the
USB mass storage class device:
– Selecting the View Angle (page 18)
– Special Effect Playback (page 19)
– Program Play (page 20)
– A-B Repeat (page 22)
– Time Search (page 25)
• On some DVD, SVCD, or VCD discs, the actual operations
may be different from what is explained in this manual, due
to the programming and disc structure; such differences are
not a malfunction of this System.
• Some DVD Audio discs prohibit downmix. When you play
back such a disc, “LR ONLY” appears on the display and
the System plays back the left front and right front signals.
• When playing back a DVD Audio disc recorded in MLP
(Meridian Lossless Packing; a lossless audio compression
system that can completely recreate the PCM signal), the
signals are recognized as the linear PCM signals, however,
no indicator lights up on the display.
• This System can recognize up to 4 000 tracks in a disc.
Also, the System can recognize up to 150 tracks per group
and up to 99 groups in a disc.
– If there are any unplayable files in a folder, those files are
also counted in the total file number.
– Playable files which do not belong to any groups are
handled as GROUP 1.
• For playback of files in the USB mass storage class
device...
– While the System is reading a disc, changing the source
to USB MEMORY may cause the System to continue
playback the DVD/CD source. In this case, press 7 on
the main unit to reactivate the USB source.
– When connecting a USB mass storage class device, refer
also to its manual.
– Connect one USB mass storage class device to the
System at a time. Do not use a USB hub.
– You cannot charge any USB device through the USB
MEMORY jack of this System.
– While playing back a file in a USB mass storage class
device, do not disconnect the device. It may cause
malfunction on both the System and the device.
– JVC bears no responsibility for any loss of data in the
USB mass storage class device while using this System.
– When connecting with a USB cable, use the cable whose
length is less than 1 m.
– This System is compatible with the USB Full-Speed (not
compatible with the USB 1.1).
– You can playback the following types of files in a USB
mass storage class device (maximum data transfer rate:
2 Mbps):
– Music: MP3, WMA
– Picture: JPEG
– Movie: MPEG-1, MPEG-2, ASF, DivX (maximum
frame rate of 30 fps for progressive)
– You cannot playback a file larger than 2 Gigabyte.
– When playing a file which has a large transfer rate,
frames or sounds may be dropped during playback.
– This System cannot recognize a USB mass storage class
device whose rating is other than 5 V and does not exceed
500 mA.
– This System may not playback some USB mass storage
class devices and does not support DRM (Digital Rights
Management).
– This System may not playback some files even though
their formats are listed above.
• For DVD-VR playback...
– This System can play only a disc of UDF-Bridge format.
– For details about DVD-VR format and play list, refer to
the manual of the recording equipment.
– You cannot use reverse slow motion, Program Play, or
Random Play.
• For MP3/WMA playback...
– MP3/WMA discs require a longer readout time than
regular CDs. (It depends on the complexity of the group/
file configuration.)
– Some MP3/WMA files cannot be played back and will
be skipped. This results from their recording processes
and conditions.
– This System can play only a disc of ISO 9660 Level 1 or
Level 2.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the
letter case—upper/lower).
– It is recommended that you make each MP3/WMA file at
a sampling rate of 44.1 kHz and at a bit rate of 128 kbps.
This System cannot play back files made at a bit rate of
less than 64 kbps.
UX-G60[B].book Page 33 Thursday, February 9, 2006 1:15 PM