LCT0979-002B_Cover.fm Page 1 Tuesday, September 10, 2002 3:55 PM SUPER PROJECTOR MANUEL D’INSTRUCTIONS : SUPER PROJECTEUR ENGLISH INSTRUCTIONS FRANÇAIS DLA-M5000LE DLA-M5000SCE QUICK ALIGN.
LCT0979-002A_Cover.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 1 Tuesday, March 12, 2002 3:59 PM Thank you for purchasing this projector. Before using it, read and follow all instructions carefully to take full advantage of the projector’s capabilities. SAFETY PRECAUTIONS IMPORTANT INFORMATION IMPORTANT SAFEGUARDS To reduce the risk of electric shock, do not remove cover. Refer servicing to qualified service personnel.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 2 Tuesday, March 12, 2002 3:59 PM – This product should be operated only with the type of power source indicated on the label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. – This product is equipped with a three-wire plug. This plug will fit only into a grounded power outlet.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 3 Tuesday, March 12, 2002 3:59 PM POWER CONNECTION (United Kingdom only) WARNING Do not cut off the main plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter or consult your dealer.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 4 Tuesday, March 12, 2002 3:59 PM Contents SAFETY PRECAUTIONS ................. 1 Contents ........................................... 4 Accessories ..................................... 4 Controls and Features .................... 5 Front Side / Top Surface / Right Side .....................5 Left-hand side / Back Side ......................................6 Control Panel ..........................................................
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 5 Tuesday, March 12, 2002 3:59 PM Controls and Features CAUTIONS • Be careful as paper, cloth or soft cushion could be drawn in if placed nearby. Do not block the intake area, or heat may build up and could cause a fire. • Clean the filter periodically. For details, refer to “Cleaning and Replacing the Filter” on page 58.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 6 Tuesday, March 12, 2002 3:59 PM Controls and Features Left-hand side / Back Side 8 Exhaust vents Vents for cooling fans through which warm air comes out. 9 Control panel For details, refer to “Control Panel” on page 7 and 8. p Remote sensor When operating with the remote control, aim it toward this sensor. An additional remote sensor is provided on the front of the projector.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 7 Tuesday, March 12, 2002 3:59 PM Controls and Features Control Panel STAND BY OPERATE LAMP TEMP EMERGENCY 1 STAND BY Indicator ON: When in stand-by mode. Blinking: When in cool-down mode. AV RGB SETTING QUICK ALIGN. 6 EMERGENCY indicator Blinking:Something abnormal has occurred with the projector.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 8 Tuesday, March 12, 2002 3:59 PM Controls and Features Control Panel (Cont.) STAND BY OPERATE LAMP TEMP EMERGENCY 7 AV button Use this button to select a device such as a video deck connected to the EXT. IN terminal of the projector. Each time you press the button, the device selected changes as follows: Y/C* VIDEO* YPBPR * Y/C and VIDEO can be used only when a video board separately sold has been installed.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 9 Tuesday, March 12, 2002 3:59 PM Controls and Features Connector Panel Y/C RGB VIDEO RGB IN-1 R RGB IN-2 EXT. IN Y G H/CS PB/B-Y B V PR/R-Y REMOTE CONTROL RGB OUT 4 REMOTE terminal (mini jack) This terminal is used to directly connect the remote control to the projector. Use the remote control cable supplied. An infrared remote control extension unit can also be connected to the jack.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 10 Tuesday, March 12, 2002 3:59 PM Controls and Features Remote Control Unit QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET LENS LOCK UNLOCK EN ME NU / R TE RGB/COMPUTER AV U T + SHIFT ZOOM FOCUS D W – LENS 7 1 Remote control’s signal transmitter 2 OPERATE button To turn on or off the power, press this button for one or more seconds.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 11 Tuesday, March 12, 2002 3:59 PM Controls and Features Remote Control Unit (Cont.) QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET QUICK ALIGN. OPERATE AV HIDE PAGE BACK EN ME NU / EN TE R TE LENS LOCK UNLOCK R LENS LOCK UNLOCK PRESET ME NU / RGB/COMPUTER AV RGB/COMPUTER U T + SHIFT ZOOM FOCUS D W – Y/C* VIDEO* YPBPR T + ZOOM FOCUS D W – LENS + VOLUME LENS – e QUICK ALIGN.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 12 Tuesday, March 12, 2002 3:59 PM Controls and Features MENU/ENTER (Menu Operation) Button The remote control supplied with this projector has only one button to navigate through the menus. Pressing the menu operation button too strongly may cause an incorrect operation. So, before you use the button in an actual situation, have some practice to make yourself familiar with using the button.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 13 Tuesday, March 12, 2002 3:59 PM Installing the Projector Precautions for Installation CAUTION • Since the projector weighs approx. 70 kg (154 lbs.), be sure to use four or more people when lifting or moving it; otherwise, the projector could possibly drop, causing personal injury and/or damage to the projector. • Do not install the projector in the following places: • There is much water, humidity or dust.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 14 Tuesday, March 12, 2002 3:59 PM Installing the Projector Precautions for Installation (Cont.) ■ Observe the following points when installing the projector by hanging it from the ceiling • To prevent falling or overturning, it is recommended that the projector be fixed to its stand with bolts. • When mounting the projector to the ceiling, first install a special shelf and then set the projector on it securely.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 15 Tuesday, March 12, 2002 3:59 PM Installing the Projector Lens Shift Function ■ Change of projection screen according to aspect ratio Screen with 4 : 3 aspect ratio Screen Screen with 16 : 9 aspect ratio 90° 90° 90° Center line of the lens The separately sold lenses used on the projector have a lens shift function.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 16 Tuesday, March 12, 2002 3:59 PM Installing the Projector Lens Shift Function (Cont.) Maximum amount of shift The maximum amount of vertical shift is restricted by the amount of horizontal shift made.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 17 Tuesday, March 12, 2002 3:59 PM Installing the Projector Projection Distances and Screen Sizes Lenses that can be used are a 3 : 1 ~ 7 : 1 zoom lens and a 1.5 : 1 fixed-focus lens. With a zoom lens used, you have a wider latitude in selecting projection distance and installation space than with a fixed lens. For how to install the lens, consult the dealer who installed and adjusted your projector or service center.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 18 Tuesday, March 12, 2002 3:59 PM Connecting to Various Devices * Before connection, be sure to turn off the projector and connected devices. * Read the manual which comes with each device thoroughly. Signals that Can Be Input to the Projector The following signals can be input to the projector: ■ Video signals (1) Response to color systems Color system Input terminal NTSC 480i NTSC 4.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 19 Tuesday, March 12, 2002 3:59 PM Connecting to Various Devices Examples of System Configuration Before connection, be sure to turn off both the projector and the equipment to be connected. • Also, read the manuals which came with the equipment. Example of a basic system • By connecting an RGB switcher, a variety of input sources can be input to the projector as RGB signals.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 20 Tuesday, March 12, 2002 3:59 PM Connecting to Various Devices Connecting to Computer Devices Before connection, be sure to turn off both the projector and computer devices. • Read the manual which comes with each device thoroughly. • Use the separately available computer connection cable. Also, prepare cables required for connecting the devices connected.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH Body Eng U&E.fm Page 21 Wednesday, March 13, 2002 8:13 PM Connecting to Various Devices Connecting to Devices which Control the Projector Before connection, be sure to turn off both the projector and devices to be connected. • Read the manual thoroughly which comes with each device to be connected. • By connecting a computer to the RS-232C terminal, you can control the projector. * For details, consult an authorized your dealer or service center.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 22 Tuesday, March 12, 2002 3:59 PM Connecting to Various Devices Connecting the Power Cord (Supplied) After all devices have finished being connected, connect the projector’s power cord. At this time, do not turn on the MAIN POWER switch yet. ■ Preparation Attach a plug which matches your wall outlet, to the power cord. For how to attach a plug, consult your dealer or a local service center.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 23 Tuesday, March 12, 2002 3:59 PM Connecting to Various Devices When Turning On the Devices Connected to the Projector Turn on the switches of the projector and the devices connected in the following order. Skip over unconnected devices if there is any.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 24 Tuesday, March 12, 2002 3:59 PM Basic Operations ■ Projector’s buttons The following describes the basic procedure for normal use of the projector. STAND BY indicator 1. Turning on the Power OPERATE indicator 1 Turn on the MAIN POWER switch of the projector. STAND BY OPERATE TEMP EMERGENCY LAMP AV RGB ON [ ❙ ]: The main power turns on and the STAND BY indicator comes on.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 25 Tuesday, March 12, 2002 3:59 PM Basic Operations ■ Projector’s buttons 2. Select the video input to be projected AV button ■ Press the AV button or the RGB button to switch the input. • Each time you press either button, the selected input changes as follows. When you press VIDEO: TEMP EMERGENCY LAMP RGB AV SETTING RGB button VIDEO Y/C QUICK ALIGN.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 26 Tuesday, March 12, 2002 3:59 PM Basic Operations ■ Projector’s buttons 4. Adjust focus ■ Adjust focus with the remote control’s FOCUS (+/–) buttons. EMERGENCY RGB AV SETTING QUICK ALIGN. When adjusting the focus with the FOCUS buttons, set the LENS LOCK j UNLOCK switch to the UNLOCK position. Remote control unit + QUICK ALIGN. button FOCUS – Note ■ Remote control unit LENS LOCK j UNLOCK switch QUICK ALIGN.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 27 Tuesday, March 12, 2002 3:59 PM Basic Operations ■ Projector’s button LAMP TEMP EMERGENCY AV ■ To display the SETTING menu RGB SETTING QUICK ALIGN. The setting menu is used to make basic adjustments and settings (TRACKING, PHASE, H. POS., V. POS., FOCUS and ZOOM) of the video picture being projected after installation (connection) or after inputs are switched.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 28 Tuesday, March 12, 2002 3:59 PM Basic Operations ■ Remote control unit ■ To display “CHANNEL” on the screen AV HIDE button QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET PAGE BACK button LENS LOCK UNLOCK EN ME NU / While no menu is displayed, pressing the PAGE BACK button causes the channel now being used to appear. You can also switch channels.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 29 Tuesday, March 12, 2002 3:59 PM Operating the Setting Menu Making Basic Settings ■ Projector’s buttons In this section, we are making basic picture adjustments which should be performed after installation (connection). SETTING button SETTING QUICK ALIGN. QUICK ALIGN. button ■ Setting menu 1 SETTING • The setting menu is displayed on the screen. 2 Press the SETTING button to select the desired item.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 30 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Configuration the Main Menu (AV Input) For computer inputs, see the following page. You can adjust video quality (PICTURE) and etc. using the menus. The menus are configured as follows: Main menu (AV inputs: During EXT. IN input signal) Main menu (AV inputs: During EXT. IN input signal) PIXEL CLOCK POSITION PICTURE OPTIONS TRACKING: Normally, no adjustment is required.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 31 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Configuration of the Main Menu (Computer-related input) Main menu (Computer-related inputs: During COMPUTER IN -1 or -2 input signal) PIXEL CLOCK POSITION PICTURE OPTIONS TRACKING: The lateral size and display area of video image are adjusted. PHASE: Flickering or dim video image is adjusted. V. POS.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 32 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Operating the Main Menu (Basic Operation of the Main Menu) ■ Remote control unit QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET PAGE BACK button LENS LOCK UNLOCK ME NU / For projector’s menus, the setting menu and the main menu are available. Here, we explain about the operation of the main menu. For the setting menu, refer to “Making Basic Settings” on page 29.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 33 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Changing the Color System ■ Remote control unit OPERATE AV HIDE PAGE BACK PAGE BACK button LENS LOCK UNLOCK ME NU / 1 EN • The main menu is shown on the screen. R TE MENU/ENTER button 2 U T + SHIFT ZOOM FOCUS D W – Press MENU/ENTER toward the 5 or ∞ mark to select “DECODER”. • The selected item (displayed in text) is shown in magenta color on the screen.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 34 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Changing the Language Display ■ Remote control unit QUICK ALIGN. The language in the menu display is set to English when shipped from the factory. When you want to change to another language, set it as follows. OPERATE AV HIDE PAGE BACK PRESET PAGE BACK button LENS LOCK UNLOCK ME NU / 1 Press the MENU/ENTER button. • The main menu is shown on the screen.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 35 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Adjusting the Pixel Clock ■ Remote control unit QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET PAGE BACK button LENS LOCK UNLOCK EN ME NU / R TE MENU/ENTER button U T + SHIFT ZOOM FOCUS D W – 1 Press the MENU/ENTER button. • The main menu appears on the screen. 2 RGB/COMPUTER AV The pixel clock should be adjusted mainly for computerrelated inputs.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 36 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Adjusting the Screen Position ■ Remote control unit Adjust the position of the screen if it is displaced. 1 QUICK ALIGN. OPERATE • The main menu appears on the screen.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 37 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Adjusting Picture Quality ■ Remote control unit QUICK ALIGN. Adjust brightness, contrast, etc. so you have the desired screen. Adjustment items (on the PICTURE menu) are different when video-related signals are input and when computer-related signals are input.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 38 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Adjusting Picture Quality (Cont.) ■ Remote control unit QUICK ALIGN. 5 OPERATE For video system input AV HIDE PAGE BACK PRESET PAGE BACK button LENS LOCK UNLOCK EN ME NU / R TE MENU/ENTER button RGB/COMPUTER AV Press MENU/ENTER toward the 2 or 3 mark to adjust the selected item. • To adjust multiple items, repeat steps 4 and 5.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 39 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Adjusting Picture Quality (Cont.) ■ Remote control unit Adjustment item QUICK ALIGN. OPERATE AV HIDE PAGE BACK button LENS LOCK UNLOCK EN ME NU / R TE U T + SHIFT ZOOM FOCUS D W – 3 Gets brighter. (–30 = 0 = +30) 2 Gets lower. (–30 + 0 + +30) 3 Gets higher. (–30 = 0 = +30) 2 Gets less reddish. (–30 + 0 + +30) 3 Gets more reddish.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 40 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Setting and Adjusting Other Functions (OPTIONS) ■ Remote control unit QUICK ALIGN. The following optional functions can be set (adjusted). OPERATE AV HIDE PAGE BACK PRESET PAGE BACK button LENS LOCK UNLOCK EN R TE MENU/ENTER button RGB/COMPUTER U T + SHIFT ZOOM FOCUS W – D MENU AUTO OFF TOP BOTTOM INV.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 41 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Setting and Adjusting Other Functions (OPTIONS) (Cont.) ■ Remote control unit OPERATE • To adjust multiple items, repeat steps 4 and 5. Button LENS LOCK UNLOCK EN ME NU / R TE MENU/ENTER button 2/3 LINE DISPLAY 2/3 RIGHT LEFT REV. 2/3 TOP BOTTOM INV.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 42 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Setting and Adjusting Other Functions (OPTIONS) (Cont.) ■ Remote control unit Adjustment item QUICK ALIGN. Button Adjustment content 2/3 Sets background color when there is no input signal.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 43 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Changing (Setting) the Source ■ Remote control unit QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET PAGE BACK button LENS LOCK UNLOCK EN ME NU / R TE MENU/ENTER button Normally, use the source setting in AUTO.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 44 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Changing (Setting) the Source (Cont.) ■ Remote control unit 5 Press MENU/ENTER to set (fix). When a source setting “AUTO” is selected: QUICK ALIGN.
DLA-M5000LE/SCE / LCT0979-002B / ENGLISH Body Eng U&E.fm Page 45 Tuesday, September 10, 2002 3:48 PM Operating the Main Menu Changing (Setting) the Source (Cont.) ■ Remote control unit QUICK ALIGN. When a source setting “USER” is selected: The “USER SOURCE setup menu” is displayed. • On the “USER SOURCE setup menu (user)”, a source created by the user can be selected. • To select a user area, it must already be user-registered with the “USER SOURCE setup menu”. (See pages 53 to 55.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 46 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Setting Up Channels ■ Remote control unit QUICK ALIGN. When you set up channels, you can select a line and a multiple of sources (up to 30) for each channel. If you are using a switcher and set switcher numbers, you can also select each channel from the switcher side.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 47 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Setting Up Channels (LINE setup) ■ Remote control unit When LINE is selected: The “LINE selection menu” screen appears. QUICK ALIGN.
DLA-M5000LE/SCE / LCT0979-002B / ENGLISH Body Eng U&E.fm Page 48 Tuesday, September 10, 2002 3:48 PM Operating the Main Menu Setting Up Channels (SOURCE setup) ■ Remote control unit QUICK ALIGN. ■ When “SOURCE” is selected: The “SOURCE registration” screen appears. • To be able to display a menu, a “LINE” needs to be already registered. • Sources already selected are indicated with check marks.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 49 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Setting Up Channels (SOURCE setup) (Cont.) ■ Remote control unit QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET PAGE BACK button LENS LOCK UNLOCK EN ME NU / R TE MENU/ENTER button ■ Pressing PAGE BACK twice will bring you back to the main menu. To finish the main menu, press PAGE BACK again. RGB/COMPUTER AV U T + SHIFT ZOOM FOCUS W – D 2.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 50 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Setting Up Channels (SW No setup) ■ Remote control unit QUICK ALIGN. This setup procedure is to make dedicate switcher operation linked to the selection of designated channels. OPERATE When a switcher number “SW No” is selected: AV HIDE PAGE BACK PRESET LENS LOCK UNLOCK The “Switcher number setup menu” is displayed.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 51 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Changing Channels (CH Change) ■ Remote control unit QUICK ALIGN. Channels which have lines and sources registered can be switched. The channels can be switched by using either a direct channel or the “CHANNEL setup • selection” menu.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 52 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Changing Channels (CH Change) (Cont.) ■ Remote control unit QUICK ALIGN. ■ To switch on the “CHANNEL setup • selection” menu : 1 OPERATE AV HIDE PAGE BACK PRESET •The main menu appears on the screen. PAGE BACK button LENS LOCK UNLOCK 2 EN ME NU / Press the MENU/ENTER button.
DLA-M5000LE/SCE / LCT0979-002B / ENGLISH Body Eng U&E.fm Page 53 Tuesday, September 10, 2002 3:49 PM Operating the Main Menu Setting Up (or Changing) User Sources ■ Remote control unit QUICK ALIGN. A maximum of 10 types of information can individually be registered regarding the source being input and projected through the line connection.
DLA-M5000LE/SCE / LCT0979-002B / ENGLISH Body Eng U&E.fm Page 54 Tuesday, September 10, 2002 3:49 PM Operating the Main Menu Setting Up (or Changing) User Sources (Cont.) ■ Remote control unit To change the registered user source name. 1 QUICK ALIGN. OPERATE PAGE BACK PRESET PAGE BACK button 2 LENS LOCK UNLOCK EN ME NU / R TE 3 RGB/COMPUTER U T + SHIFT ZOOM FOCUS D W – Press MENU/ENTER toward the 5 or ∞ mark to select a submenu item, “USER SOURCE SET UP”.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 55 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Setting Up (or Changing) User Sources (Cont.) ■ Remote control unit 6 Press the MENU/ENTER button to set. • The “USER NAME setup menu” is displayed. QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET PAGE BACK button USER NAME LENS LOCK UNLOCK EN ME NU / R TE MENU/ENTER button RGB/COMPUTER AV (USER NAME setup menu) U T + SHIFT ZOOM FOCUS D W – 1.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 56 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Setting Up (or Changing) the Display Size ■ Remote control unit QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET PAGE BACK button LENS LOCK UNLOCK EN ME NU / R TE MENU/ENTER button U T + SHIFT ZOOM FOCUS W – D Notes RGB/COMPUTER AV If the display size (horizontal effective dots and vertical effective lines of PC video boards, etc.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 57 Tuesday, March 12, 2002 3:59 PM Operating the Main Menu Setting Up (or Changing) the Display Size (Cont.) ■ Remote control unit QUICK ALIGN. AV HIDE PAGE BACK PAGE BACK button LENS LOCK UNLOCK 8 EN ME NU / R TE MENU/ENTER button U T + SHIFT ZOOM FOCUS D W – After finishing step 7, press the MENU/ ENTER button. • The main menu appears on the screen. 9 RGB/COMPUTER AV Press QUICK ALIGN.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 58 Tuesday, March 12, 2002 3:59 PM Filter Maintenance and Light-Source Lamp Replacement Cleaning and Replacing the Filter The filters should be cleaned periodically. If they are heavily stained, do not become clean if cleaned, or are damaged, replace them with new filters (Parts number: LC30505); otherwise, dirt and dust may get inside, possibly causing an adverse effect on the screen and preventing you from enjoying clear pictures.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 59 Tuesday, March 12, 2002 3:59 PM Filter Maintenance and Light-Source Lamp Replacement Cleaning and Replacing the Filter (Cont.) 4 Clean the filters. Wash the filter in water with neutral detergent, and dry it in the shade. 5 Reinstall the filters. To reinstall the filters to the projector, reverse the procedure for removing. Finally, be sure to reinstall the filter covers.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 60 Tuesday, March 12, 2002 3:59 PM Troubleshooting Solutions to common problems related to your projector are described here. If none of the solutions presented here solves the problem, unplug the projector and consult a authorized dealer or service center. Symptom Probable cause Power is not supplied. • Is the power cord disconnected? Corrective action Page • Insert the power cord (plug) firmly.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 61 Tuesday, March 12, 2002 3:59 PM Troubleshooting The projection position on the screen has shifted. Video image suddenly go out. Lens shift adjustment is not possible. • Adjust picture quality on the menu. 37, 39 • Is the correct broadcast system (color system) selected? • Set the broadcast system (color system) to AUTO. 33 • Are signals (scanning frequency, etc.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 62 Tuesday, March 12, 2002 3:59 PM Troubleshooting Symptom Remote control unit does not work. Probable cause Corrective action Page • Are batteries installed correctly? • Match the polarities of batteries correctly (+ to + and – to –). 12 • Are batteries exhausted? • Replace with new batteries. 12 • Is there a shielding object between the remote control unit and the remote sensor? • Remove any shielding objects.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 63 Tuesday, March 12, 2002 3:59 PM Specifications ■ Optical mechanism system • Projection method • D-ILA device • Projecting lens (separately available) • Screen size • Light-source lamp 3D-ILA device, 1 lens, 3 primary color optical shutter method 0.9" measured diagonally (1365 pixels × 1024 pixels) × 3 (Total number of pixels: 4,193,280) GL-M4023SZ 3:1~7:1 zoom lens GL-M4015S 1.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 64 Tuesday, March 12, 2002 3:59 PM Specifications Horizontal sync/composite sync signal (H/CS) H : 1V(p-p) to 5V(p-p), high impedance (positive/negative polarity) CS : 1V(p-p) to 5V(p-p), high impedance (positive/negative polarity) Vertical sync signal (V) V : 1V(p-p) to 5V(p-p), high impedance (positive/negative polarity) * Some connected devices may not correspond to composite sync (CS) or G on sync signal.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH DLA-M5000LE&SCE Eng Re.book Page 65 Tuesday, March 12, 2002 3:59 PM Specifications Outside dimensions ■ Top Unit: mm 30 688 30 687 747 ■ Front ■ Side 793 42 42 18 18 59 368 ~ 230 Y/C RGB 420 VIDEO RGB IN-1 R G B RGB IN-2 EXT. IN Y H/CS PB/B-Y V PR/R-Y ENGLISH 720 REMOTE CONTROL 59 RS-232C φ 50 DEUTSH RGB OUT 688 600 30 30 FRANÇAIS ■ DTV-format signals DTV-Formats 480p 720p 1080i 1080 24sF ITU-R BT.
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH Body Eng U&E.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 1 Tuesday, March 12, 2002 4:01 PM Merci d’avoir acheté ce projecteur. Avant de l’utiliser, lisez et respectez attentivement toutes les instructions pour profiter au maximum des capacités du projecteur. IMPORTANTES MESURES DE SÉCURITÉ INFORMATIONS IMPORTANTES IMPORTANTES MESURES DE SÉCURITÉ AVERTISSEMENT : INFORMATION SUR LE BRUIT MACHINE (Allemagne uniquementy) Modification de l’arrêté n°3 sur le bruit machine.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 2 Tuesday, March 12, 2002 4:01 PM – Cet appareil doit être alimenté uniquement avec le type d’alimentation indiqué sur l’étiquette. Si vous n’êtes pas sûr du type d’alimentation secteur de votre maison, consultez le revendeur de l’appareil ou votre compagnie d’électricité. – Cet appareil est équipé d’une fiche à trois broches. Elle ne peut être branchée que dans une prise secteur avec mise à la terre.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 3 Tuesday, March 12, 2002 4:01 PM CONNEXION ELECTRIQUE (Royaume-Uni seulement) AVERTISSEMENT Ne débranchez pas la fiche principale de cet appareil. Si la fiche existante ne convient pas aux prises de courant de votre maison ou si le cordon est trop court pour atteindre une prise de courant, procurez-vous un cordon prolongateur ou un adapteur de sécurité approuvé ou consultez votre revendeur.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 4 Tuesday, March 12, 2002 4:01 PM Table des matières IMPORTANTES MESURES DE SÉCURITÉ ........................................ 1 Table des matières .......................... 4 Accessoires ..................................... 4 Commandes et fonctions................ 5 Face avant / Dessus / Côté droit.............................5 Côté gauche / Arrière ..............................................6 Panneau de commande .............
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 5 Tuesday, March 12, 2002 4:01 PM Commandes et fonctions PRECAUTIONS • Faire attention car tout papier, tissu ou coussin léger se trouvant près de l’appareil peut être aspiré. Ne pas bloquer la zone d’entrée d’air. Une surchauffe pourrait se produire avec un risque d’incendie. • Nettoyer le filtre périodiquement. Pour plus de détails, référez-vous à “Nettoyage et remplacement du filtre” à la page 58.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 6 Tuesday, March 12, 2002 4:01 PM Commandes et fonctions Côté gauche / Arrière 8 Évents de sortie d’air Orifices permettant l’évacuation de l’air chaud et le refroidissement des ventilateurs. 9 Panneau de commande Pour plus de détails, référez-vous à “Panneau de commande” à la page 7 et 8. p Capteur de télécommande Lors de l’utilisation de la télécommande, la diriger vers ce capteur.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 7 Tuesday, March 12, 2002 4:01 PM Commandes et fonctions Panneau de commande 1 Indicateur STAND BY ON : Quand l’appareil est en mode d’attente. Clignotant :Quand l’appareil est en mode de refroidissement. PRECAUTIONS • Le mode de refroidissement continue pendant environ 20 secondes, pendant lesquelles la projection ne peut pas être redémarrée.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 8 Tuesday, March 12, 2002 4:01 PM Commandes et fonctions Panneau de commande (suite) STAND BY OPERATE LAMP TEMP EMERGENCY 7 Touche AV Utilisez cette touche pour sélectionner un appareil comme un équipement vidéo raccordé à la prise EXT. IN du projecteur.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 9 Tuesday, March 12, 2002 4:01 PM Commandes et fonctions Panneau de connecteurs Y/C RGB VIDEO RGB IN-1 R RGB IN-2 EXT. IN Y G H/CS PB/B-Y B V PR/R-Y REMOTE CONTROL RGB OUT 4 Prise REMOTE (mini jack) Cette prise est utilisée pour relier la télécommande directement au projecteur. Utilisez le câble de télécommande fourni. Une unité d’extension de télécommande infrarouge peut aussi être raccordée à la prise jack.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 10 Tuesday, March 12, 2002 4:01 PM Commandes et fonctions Télécommande QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET LENS LOCK UNLOCK EN ME NU / R TE RGB/COMPUTER AV U T + SHIFT ZOOM FOCUS D W – LENS 1 Emetteur de signal pour la télécommande 2 Touche OPERATE Pour mettre l’appareil sous tension ou hors tension, appuyez sur cette touche pendant une seconde ou plus.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 11 Tuesday, March 12, 2002 4:01 PM Commandes et fonctions Télécommande (suite) QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET QUICK ALIGN.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 12 Tuesday, March 12, 2002 4:01 PM Commandes et fonctions Touche MENU/ENTER (Fonctionnement du menu) La télécommande fournie avec ce projecteur ne possède qu’une seule touche pour naviguer dans les menus. Une pression trop forte sur la touche de fonctionnement de menu peut provoquer un fonctionnement incorrect.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 13 Tuesday, March 12, 2002 4:01 PM Installation du projecteur Précautions pour l’installation PRECAUTION • Le projecteur pesant environ 70 kg, veillez à employer au moins quatre personnes pour le soulever ou le déplacer ; dans le cas contraire, vous risqueriez de le faire tomber et de provoquer des blessures corporelles et/ ou des dommages au projecteur.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 14 Tuesday, March 12, 2002 4:01 PM Installation du projecteur Précautions pour l’installation (suite) ■ Observez les points suivants lors de l’installation du projecteur au plafond : • Pour prévenir toute chute ou retournement de l’appareil, il est recommandé de fixer le projecteur à son support à l’aide de boulons. • Lors de la fixation du projecteur au plafond, installez d’abord une étagère spéciale, puis fixez-y le projecteur.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 15 Tuesday, March 12, 2002 4:01 PM Installation du projecteur Fonction de déplacement d’objectif ■ Changement d’écran de projection en fonction du format de l’image Ecran au format 4 : 3 Ecran Ecran au format 16 : 9 90° 90° 90° Ligne centrale de l’objectif Les objectifs vendus séparément utilisés sur le projecteur bénéficient d’une fonction de déplacement d’objectif.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 16 Tuesday, March 12, 2002 4:01 PM Installation du projecteur Fonction de déplacement d’objectif (suite) Déplacement maximal Le déplacement vertical maximal est limité par le déplacement horizontal effectué.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 17 Tuesday, March 12, 2002 4:01 PM Installation du projecteur Distances de projection et tailles d’écran Les objectifs utilisables sont un objectif zoom 3 : 1 ~ 7 : 1 et un objectif à mise au point fixe 1,5 : 1. Lorsque vous utilisez un objectif zoom, vous disposez d’une latitude plus importante dans la sélection de la distance de projection et de l’espace d’installation.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 18 Tuesday, March 12, 2002 4:01 PM Raccordement avec différents appareils * Avant la connexion, assurez-vous que le projecteurs et autres appareils à raccorder sont éteints. * Bien lire le manuel fourni avec chaque appareil. Signaux pouvant être entrés dans le projecteur Les signaux suivants peuvent être entrés dans le projecteur : ■ Signaux vidéo (1) Réponse aux systèmes de couleur Système de couleur NTSC 480i NTSC 4.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 19 Tuesday, March 12, 2002 4:01 PM Raccordement avec différents appareils Exemples de configuration système Avant tout raccordement, assurez-vous que le projecteur et l’équipement sont hors tension. • Consultez également les manuels fournis avec l’équipement. Exemple de système de base • En raccordant un commutateur RGB, différentes sources d’entrée peuvent être entrées dans le projecteur comme signaux RGB.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 20 Tuesday, March 12, 2002 4:01 PM Raccordement avec différents appareils Raccordement aux ordinateurs Avant tout raccordement, assurez-vous que le projecteur et ordinateur sont hors tension. • Bien lire le manuel fourni avec chaque appareil. • Utilisez le câble de raccordement pour ordinateur vendu séparément. Préparez également les câbles nécessaires pour raccorder les appareils connectés.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS Body Fre U&E.fm Page 21 Wednesday, March 13, 2002 8:19 PM Raccordement avec différents appareils Raccordement à des appareils qui contrôle le projecteur Avant tout raccordement, assurez-vous que le projecteur et les appareils à raccorder sont hors tension. • Bien lire la notice d’emploi accompagnant chaque appareil devant être raccordé. • En raccordant un ordinateur à la prise RS-232C, vous pouvez contrôler le projecteur.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 22 Tuesday, March 12, 2002 4:01 PM Raccordement avec différents appareils Branchement du cordon d’alimentation (fourni) Une fois tous les appareils raccordés, branchez le cordon d’alimentation du projecteur. À ce stade, n’allumez pas encore l’interrupteur MAIN POWER. ■ Préparation Raccordez une prise (adaptée à la prise de courant) au cordon d’alimentation.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 23 Tuesday, March 12, 2002 4:01 PM Raccordement avec différents appareils Lors de la mise en marche des périphériques raccordés au projecteur Allumez les interrupteurs du projecteur et des périphériques raccordés dans l’ordre suivant. Ignorez les périphériques non raccordés s’il y en a.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 24 Tuesday, March 12, 2002 4:01 PM Fonctionnement de base ■ Touches du projecteur Ce qui suit décrit la procédure de base pour une utilisation normale du projecteur. Indicateur STAND BY Indicateur OPERATE 1. Mettre sous tension 1 Allumez l’interrupteur MAIN POWER du projecteur. STAND BY OPERATE LAMP TEMP EMERGENCY AV RGB ON [ ❙ ] : L’appareil est mis sous tension et l’indicateur STAND BY s’allume.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 25 Tuesday, March 12, 2002 4:01 PM Fonctionnement de base ■ Touches du projecteur 2. Sélection de l’entrée vidéo à projeter Touche AV ■ Appuyer sur la touche AV ou RGB pour basculer l’entrée. • A chaque action sur une de ces touches, l’entrée sélectionnée change comme suit. Lorsque vous appuyez sur VIDEO: TEMP EMERGENCY LAMP AV RGB SETTING QUICK ALIGN.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 26 Tuesday, March 12, 2002 4:01 PM Fonctionnement de base ■ Touches du projecteur 4. Réglage de la mise au point ■ Réglez la mise au point à l’aide des touches FOCUS (+/–) de la télécommande. EMERGENCY RGB AV SETTING QUICK ALIGN. Lors du réglage de la mise au point avec les touches FOCUS, réglez le commutateur LENS LOCK j UNLOCK sur la position UNLOCK. Télécommande + Touche QUICK ALIGN.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 27 Tuesday, March 12, 2002 4:01 PM Fonctionnement de base ■ Touche du projecteur LAMP TEMP EMERGENCY AV ■ Pour afficher le menu REGLAGE RGB SETTING QUICK ALIGN. Le menu de réglage permet d’effectuer des réglages de base (TRACK, PHASE, POSITION H., POSITION V., FOCUS et ZOOM) sur l’image vidéo projetée après installation (raccordement) ou après basculement des entrées.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 28 Tuesday, March 12, 2002 4:01 PM Fonctionnement de base ■ Télécommande ■ Pour afficher “CHANNEL” à l’écran Touche AV HIDE QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET Touche PAGE BACK LENS LOCK UNLOCK EN ME NU / R TE RGB/COMPUTER AV Lorsqu’aucun menu n’est affiché, une pression sur la touche PAGE BACK provoque l’affichage du canal utilisé actuellement. Vous pouvez aussi basculer d’un canal à un autre.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 29 Tuesday, March 12, 2002 4:01 PM Utilisation du menu de réglage Réglages de base ■ Touches du projecteur Dans cette section, nous allons réaliser des réglages de base de l’image qui doivent être exécutés après l’installation (raccordement). Touche SETTING Remarques SETTING QUICK ALIGN. Touche QUICK ALIGN. ■ Menu de réglage 1 • Le menu de réglage est affiché à l’écran.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 30 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Configuration du menu principal (Entrée AV) Pour les entrées d’ordinateur, voir page suivante. Vous pouvez ajuster la qualité vidéo (IMAGE), etc. à l’aide des menus. Les menus sont configurés comme suit : Menu principal (Entrées AV : Avec le signal d’entrée EXT. IN) Menu principal (Entrées AV : Avec le signal d’entrée EXT.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 31 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Configuration du menu principal (entrée d’ordinateur) Menu principal (Entrées d’ordinateur : Avec le signal d’entrée COMPUTER IN -1 ou -2) OPTIONS PHASE : Ajustement du papillotement ou d’une image vidéo sombre. POSITION V. : Ajustement de la position verticale de l’image vidéo projetée. POSITION H.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 32 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Utilisation du menu principal (Utilisation de base du menu principal) ■ Télécommande QUICK ALIGN. En ce qui concerne les menus du projecteur, le menu de réglage et le menu principal sont disponibles. Nous expliquons ici le fonctionnement du menu principal. Pour des informations sur le menu de réglage, consultez “Réglages de base” à la page 29.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 33 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Changement du système de couleur ■ Télécommande QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET Touche PAGE BACK LENS LOCK UNLOCK ME NU / A la sortie d’usine, c’est le paramètre AUTO qui est réglé pour le système de couleur. Normalement, ce paramètre doit être laissé sur AUTO.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 34 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Changement de l’affichage de la langue ■ Télécommande QUICK ALIGN. A la sortie d’usine, la langue utilisée dans les menus est l’anglais. Si vous désirez changer de langue, effectuez le réglage suivant. OPERATE AV HIDE PAGE BACK PRESET Touche PAGE BACK LENS LOCK UNLOCK ME NU / 2 EN R TE U T + SHIFT ZOOM FOCUS W – Appuyez sur la touche MENU/ENTER.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 35 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Ajustement de l’horloge de pixels ■ Télécommande QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET Touche PAGE BACK LENS LOCK UNLOCK EN ME NU / R TE Touche MENU/ENTER L’horloge de pixels doit être réglée principalement pour les entrées d’ordinateur. (Normalement, il n’est pas nécessaire de l’ajuster pour les entrées vidéo.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 36 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Réglage de la position de l’écran ■ Télécommande Réglez la position de l’écran si celle-ci est incorrecte. 1 QUICK ALIGN.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 37 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Ajustement de la qualité de l’image ■ Télécommande QUICK ALIGN. Ajustez la luminosité, le contraste, etc. jusqu’à obtenir l’image souhaitée. Les éléments d’ajustement (dans le menu IMAGE) sont différents lorsque des signaux vidéo et des signaux d’ordinateur sont entrés.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 38 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Ajustement de la qualité de l’image (suite) ■ Télécommande QUICK ALIGN. 5 OPERATE AV HIDE PAGE BACK PRESET Touche PAGE BACK LENS LOCK UNLOCK EN ME NU / R TE Touche MENU/ENTER RGB/COMPUTER AV U T + SHIFT ZOOM FOCUS W – D Appuyez sur MENU/ENTER vers la marque 2 ou 3 pour ajuster l’élément sélectionné.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 39 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Ajustement de la qualité de l’image (suite) ■ Télécommande Elément d’ajustement QUICK ALIGN. Touche Contenu de l’ajustement OPERATE AV HIDE PAGE BACK PRESET Touche PAGE BACK LENS LOCK UNLOCK 3 Eclaircit. (–30 = 0 = +30) 2 Diminue. (–30 + 0 + +30) 3 Augmente. (–30 = 0 = +30) 2 Moins rouge. (–30 + 0 + +30) 3 Plus rouge. (–30 = 0 = +30) 2 Moins vert.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 40 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Réglage et ajustement d’autres fonctions (OPTIONS) ■ Télécommande QUICK ALIGN. Les options facultatives suivantes peuvent être définies (ajustées).
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 41 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Réglage et ajustement d’autres fonctions (OPTIONS) (suite) • Pour ajuster plusieurs éléments, répétez les étapes 4 et 5.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 42 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Réglage et ajustement d’autres fonctions (OPTIONS) (suite) ■ Télécommande Elément d’ajustement QUICK ALIGN. Touche OPERATE Définit la couleur de l’arrière-plan lorsqu’il n’y a aucun signal d’entrée.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 44 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Modification (définition) de la source (suite) ■ Télécommande QUICK ALIGN. 5 OPERATE AV HIDE PAGE BACK PRESET Touche PAGE BACK LENS LOCK UNLOCK EN ME NU / R TE Touche MENU/ENTER Appuyez sur MENU/ENTER pour régler (fixer).
DLA-M5000LE/SCE / LCT0979-002B / FRANÇAIS Body Fre U&E.fm Page 45 Tuesday, September 10, 2002 4:22 PM Utilisation du menu principal Modification (définition) de la source (suite) ■ Télécommande QUICK ALIGN. Lorsque le paramètre de source “USER” est sélectionné : Le menu de configuration “USER SOURCE est affiché. • Dans le “menu de configuration USER SOURCE (utilisateur)”, une source créée par l’utilisateur peut être sélectionnée.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 46 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Configuration des canaux ■ Télécommande QUICK ALIGN. Lorsque vous configurez des canaux, vous pouvez sélectionner une ligne et plusieurs sources (jusqu’à 30) pour chaque canal. Si vous utilisez un commutateur et définissez des numéros de commutateur, vous pouvez aussi sélectionner chaque canal du côté du commutateur.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 47 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Configuration des canaux (configuration de LINE) ■ Télécommande Lorsque LINE est sélectionné : L’écran “Menu de sélection de LINE” apparaît. QUICK ALIGN.
DLA-M5000LE/SCE / LCT0979-002B / FRANÇAIS Body Fre U&E.fm Page 48 Tuesday, September 10, 2002 4:23 PM Utilisation du menu principal Configuration des canaux (configuration de SOURCE) ■ Télécommande QUICK ALIGN. ■ Lorsque “SOURCE” est sélectionné : L’écran “Enregistrement de SOURCE” apparaît. • Pour pouvoir afficher un menu, une “LINE” doit déjà être enregistrée. • Les sources déjà sélectionnées sont indiquées par des coches.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 49 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Configuration des canaux (configuration de SOURCE) (suite) ■ Télécommande QUICK ALIGN. OPERATE AV HIDE PAGE BACK PRESET Touche PAGE BACK LENS LOCK UNLOCK EN ME NU / R TE Touche MENU/ENTER U T + SHIFT ZOOM FOCUS W – D ■ Deux pressions sur la touche PAGE BACK vous ramènent au menu principal.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 50 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Configuration des canaux (configuration de SW No) ■ Télécommande QUICK ALIGN. Cette procédure de configuration est destinée à lier le fonctionnement du commutateur dédié à la sélection des canaux dédiés.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 51 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Changement de canal (Changement de CH) ■ Télécommande QUICK ALIGN. Les canaux dont les lignes et les sources sont enregistrées peuvent être basculés. Les canaux peuvent être basculés à l’aide soit d’un canal direct, soit du menu “Configuration de CHANNEL • sélection”.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 52 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Changement de canal (Changement de CH) (suite) ■ Télécommande QUICK ALIGN. ■ Pour activer le menu “Configuration de CHANNEL • sélection” : 1 OPERATE AV HIDE PAGE BACK PRESET • Le menu principal apparaît à l’écran. Touche PAGE BACK LENS LOCK UNLOCK 2 EN ME NU / Appuyez sur la touche MENU/ENTER.
DLA-M5000LE/SCE / LCT0979-002B / FRANÇAIS Body Fre U&E.fm Page 53 Tuesday, September 10, 2002 4:24 PM Utilisation du menu principal Configuration (ou modification) des sources utilisateur ■ Télécommande QUICK ALIGN. Vous pouvez enregistrer individuellement un maximum de 10 types d’informations, en fonction de la source entrée et projetée à travers la connexion de ligne.
DLA-M5000LE/SCE / LCT0979-002B / FRANÇAIS Body Fre U&E.fm Page 54 Tuesday, September 10, 2002 4:24 PM Utilisation du menu principal Configuration (ou modification) des sources utilisateur (suite) ■ Télécommande Pour modifier le nom de source utilisateur enregistrée. 1 QUICK ALIGN.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 55 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Configuration (ou modification) des sources utilisateur (suite) ■ Télécommande QUICK ALIGN. 6 OPERATE • Le “menu de configuration USER NAME” est affiché. AV HIDE PAGE BACK PRESET Appuyez sur la touche MENU/ENTER pour définir le paramètre.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 56 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Configuration (ou modification) de la taille d’affichage ■ Télécommande QUICK ALIGN.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 57 Tuesday, March 12, 2002 4:01 PM Utilisation du menu principal Configuration (ou modification) de la taille d’affichage (suite) ■ Télécommande QUICK ALIGN. AV HIDE PAGE BACK Touche PAGE BACK LENS LOCK UNLOCK 8 EN ME NU / R TE 9 RGB/COMPUTER U T + SHIFT ZOOM FOCUS W – D Une fois l’étape 7 terminée, appuyez sur la touche MENU/ENTER.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 58 Tuesday, March 12, 2002 4:01 PM Maintenance du filtre et remplacement de la lampe source de lumière Nettoyage et remplacement du filtre Les filtres doivent être nettoyés régulièrement.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 59 Tuesday, March 12, 2002 4:01 PM Maintenance du filtre et remplacement de la lampe source de lumière Nettoyage et remplacement du filtre (suite) 4 Nettoyez les filtres. Lavez le filtre avec de l’eau et un détergent neutre, puis faites-le sécher à l’ombre. 5 Remettez les filtres en place. Pour remettre les filtres dans le projecteur, suivez la même procédure mais en sens inverse.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 60 Tuesday, March 12, 2002 4:01 PM Dépannage Les solutions aux problèmes communs avec le projecteur sont décrites ici. Si aucune des solutions présentées ici ne pouvait résoudre le problème, débranchez le projecteur et consultez un revendeur autorisé ou un centre de service. Symptôme Pas d’alimentation. Cause probable • Le cordon d’alimentation est-il débranché ? Action corrective • Bien brancher le cordon d’alimentation (prise).
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 61 Tuesday, March 12, 2002 4:01 PM Dépannage Page • Les paramètres TRACK et PHASE sont- • Ajustez les paramètres TRACK et ils ajustés correctement ? PHASE avec le menu. 29, 35 • La qualité de l’image (densité de couleur, etc.) est-elle ajustée correctement ? • Ajustez la qualité de l’image avec le menu. 37, 39 • Le CLAMP correct est-il sélectionné ? • Sélectionnez le CLAMP correct dans le OPTION MENU.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 62 Tuesday, March 12, 2002 4:01 PM Dépannage Symptôme L’image vidéo disparaît soudainement. Cause probable Action corrective Page • La vidéo n’a-t-elle pas été arrêtée par une pression sur la touche AV HIDE de la télécommande ? • Appuyez sur la touche AV HIDE de la télécommande pour activer la vidéo. 11 • Tous les signaux de couleur vidéo sontils entrés ? • Vérifiez les signaux et les raccordements.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.book Page 65 Tuesday, March 12, 2002 4:01 PM Spécifications Dimensions extérieures ■ Haut Unité : mm 30 688 30 687 747 ■ Avant ■ Côté 793 42 42 18 18 59 368 ~ 230 Y/C RGB 420 VIDEO RGB IN-1 R G B RGB IN-2 EXT. IN Y H/CS PB/B-Y V PR/R-Y ENGLISH 720 REMOTE CONTROL 59 RS-232C φ 50 FRANÇAIS RGB OUT 688 600 30 30 FRANÇAIS ■ Signaux de format DTV Formats DTV 480p 720p 1080i 1080 24sF ITU-R BT.
DLA-M5000CLE (Re)/ LCT0979-002A / FRANÇAIS DLA-M5000LE&SCE Fre Re.
LCT0979-002A_Cover.
LCT0979-002B_Cover.