Owner's Manual
Table Of Contents
- Instructions
- Getting Started
- Set up
- Operate
- Adjust/Set
- Maintenance
- Troubleshooting
- Others
- Quick Start Guide
- External Command Communication Specification
- 1 Outline
- 2 Interface
- 3 Protocol
- 4 Command control
- 4.1 NULL command
- 4.2 Power [PoWer]
- 4.3 Input [InPut]
- 4.4 Remote control pass-through [RemoteCode]
- 4.5 Setup [SetUp]
- 4.6 Gamma data of Gamma table “Custom 1/2/3” [GammaRed, Green, Blue]
- 4.7 Panel Alignment (zone) Data [Panel Alignment(Zone) Red, Blue]
- 4.8 Source Asking [SourCe]
- 4.9 Model status asking [MoDel]
- 4.10 Adjustment [AdjustmentCommand]
- Command code
- Parameter1
- Parameter2
- 4.10.1 Special data
- Special data
- Picture mode
- Color Profile
- Color Temp. Table Data
- Color Temp. Correction Data
- Gamma Table Data
- Gamma Correction Data
- Dynamic Control Data
- Color Management Data
- Low Latency Data
- Clear Motion Drive Data
- Motion Enhance Data
- LD Power Data
- Graphic Mode Data
- HDMI Input Level Data
- HDMI Color Space Data
- HDMI 2D/3D Data
- Aspect Data
- Mask Data
- Lens Control(Focus Near, Focus Far, Zoom Tele, Zoom Wide, Shift Left, Shift Right, Shift Up, Shift Down) Data
- Lens Image Pattern, Lens Lock, Screen Adjust, Uniformity Correction Data
- Installation Style Data
- Anamorphic Data
- Panel Alignment Switch Data
- High Altitude mode
- Back Color Data
- Menu Position Data
- Source Display
- Language Data
- Trigger Data
- Off Timer Data
- Eco Mode Data
- Control 4 Data
- Input Data
- Source Data
- Deep Color Data
- Color Space Data
- Colorimetry Data
- HDR Data
- 4.10.2 Special2 Data
- 4.10.3 Special3 Data
- 4.10.4 Special9 Data
- 4.10.5 Special10 Data
- 4.10.6 Special14 Data
- 4.10.7 Operation
- 4.10.8 Reference
- LAN setup [Lan Setup]
- Screen Codes
- Safety Precautions
3 Protocol
6 / 45 PJ05030305B
3.4 Unit ID table
The unit ID consists of two bytes, the unit code and the individual code.
The unit code is 0x89(Fixed)
The individual code signifies “projector ID” and it is fixed on 0x01.
A changed individual code is preserved on the unit side.
Unit code
b7
b6
b5
b4
b3
b2
b1
b0
1
0
0
0
1
0
0
1
Fixed
Individual code
b7
b6
b5
b4
b3
b2
b1
b0
0
0
0
0
0
0
0
1
ID = 1 (Fixed)
3.5 Command table
The command consists of two bytes of ASCII characters.
HEX
ASCII
Function
Operation
Reference
0x00,
0x00
NUL
NUL
NULL command
-
0x50,
0x57
'P'
'W'
Power [PoWer]
0x49, 0x50
'I'
'P'
Input [InPut]
0x52,
0x43
'R'
'C'
Remote control code through [Remote Code]
-
0x53,
0X55
'S'
'U'
Initial setup [SetUp]
0x47,
0x52
'G'
'R'
Gamma data (Red) of the Gamma table ”Custom 1/2/3” [Gamma Red]
0x47,
0x47
'G'
'G'
Gamma data (Green) of the Gamma table ”Custom 1/2/3” [Gamma Green]
0x47,
0x42
'G'
'B'
Gamma data (Blue) of the Gamma table ”Custom 1/2/3” [Gamma Blue]
0x50,
0x52
‘P’
‘R’
Red of Panel Alignment (zone)
0x50,
0x42
‘P’
‘B’
Blue of Panel Alignment (zone)
0x53,
0x43
'S'
'C'
Source asking [SourCe]
-
0x4D,
0x44
'M'
'D'
Model status asking [MoDel]
-
0x50,
0x4D
'P'
'M'
Picture adjustment [adjustment of Picture] : Picture Adjust
0x49, 0x53
'I'
'S'
Picture adjustment [adjustment of Picture] : Input Signal
0x49,
0x4E
'I'
'N'
Picture adjustment [adjustment of Picture] : Installation
0x44,
0x53
'D'
'S'
Picture adjustment [adjustment of Picture] : Display Setup
0x46,
0X55
'F'
'U'
Picture adjustment [adjustment of Picture] : Function
0x49,
0x46
'I'
'F'
Picture adjustment [adjustment of Picture] : Information
-
0x4C
0x53
'L'
'S'
LAN setup [Lan Setup]