Owner's Manual
Table Of Contents
- Instructions
- Getting Started
- Set up
- Operate
- Adjust/Set
- Maintenance
- Troubleshooting
- Others
- Quick Start Guide
- External Command Communication Specification
- 1 Outline
- 2 Interface
- 3 Protocol
- 4 Command control
- 4.1 NULL command
- 4.2 Power [PoWer]
- 4.3 Input [InPut]
- 4.4 Remote control pass-through [RemoteCode]
- 4.5 Setup [SetUp]
- 4.6 Gamma data of Gamma table “Custom 1/2/3” [GammaRed, Green, Blue]
- 4.7 Panel Alignment (zone) Data [Panel Alignment(Zone) Red, Blue]
- 4.8 Source Asking [SourCe]
- 4.9 Model status asking [MoDel]
- 4.10 Adjustment [AdjustmentCommand]
- Command code
- Parameter1
- Parameter2
- 4.10.1 Special data
- Special data
- Picture mode
- Color Profile
- Color Temp. Table Data
- Color Temp. Correction Data
- Gamma Table Data
- Gamma Correction Data
- Dynamic Control Data
- Color Management Data
- Low Latency Data
- Clear Motion Drive Data
- Motion Enhance Data
- LD Power Data
- Graphic Mode Data
- HDMI Input Level Data
- HDMI Color Space Data
- HDMI 2D/3D Data
- Aspect Data
- Mask Data
- Lens Control(Focus Near, Focus Far, Zoom Tele, Zoom Wide, Shift Left, Shift Right, Shift Up, Shift Down) Data
- Lens Image Pattern, Lens Lock, Screen Adjust, Uniformity Correction Data
- Installation Style Data
- Anamorphic Data
- Panel Alignment Switch Data
- High Altitude mode
- Back Color Data
- Menu Position Data
- Source Display
- Language Data
- Trigger Data
- Off Timer Data
- Eco Mode Data
- Control 4 Data
- Input Data
- Source Data
- Deep Color Data
- Color Space Data
- Colorimetry Data
- HDR Data
- 4.10.2 Special2 Data
- 4.10.3 Special3 Data
- 4.10.4 Special9 Data
- 4.10.5 Special10 Data
- 4.10.6 Special14 Data
- 4.10.7 Operation
- 4.10.8 Reference
- LAN setup [Lan Setup]
- Screen Codes
- Safety Precautions
4 Command control
11 / 45 PJ05030305B
4.2 Power [PoWer]
Used for power ON/OFF operation and for referencing the power setting state of the projector.
Command code
Table 4-2 POWER CMD
HEX
ASCII
Function
Operation
Reference
0x50 0x57
'P'
'W'
Power [POWER]
Parameters
Table 4-3 POWER CMD DATA
HEX
ASCII
Operation
0x30
'0'
Power OFF
0x31
'1'
Power ON
【Data 0】
Table 4-4 POWER CMD STATUS
4.2.1 Operation
Use the command as shown in the following examples.
Purpose: To turn the Projector’s power OFF. (Current state: Power-ON)
(1) Data is transmitted from the external controller to the Projector as follows.
1: External controller →
0x21
0x89
0x01
0x50
0x57
0x30
0x0A
'!'(Operation)
PJ
Individual : 1
'P'
'W'
OFF
End
(2) If the projector receives data (1) and the command reception is normal, the projector returns an ACK as follows.
2: ← Projector
0x06
0x89
0x01
0x50
0x57
0x0A
ACK
PJ
Individual : 1
'P'
'W'
End
(3) The projector turns power OFF.
The power can be turned OFF by the above exchange.
The power-OFF operation can be done by a sequence similar to that for power-ON.
The projector ignores data in the same state. For example, even if power-ON data is sent with the projector in power-ON mode,
no projector operation is done.
HEX
ASCII
Operation
0x30
'0'
Standby
0x31
'1'
Lamp On
0x32
'2'
Cooling
0x33
'3'
Reserved
0x34
'4'
Error