Owner's Manual
Table Of Contents
- Instructions
- Getting Started
- Set up
- Operate
- Adjust/Set
- Maintenance
- Troubleshooting
- Others
- Quick Start Guide
- External Command Communication Specification
- 1 Outline
- 2 Interface
- 3 Protocol
- 4 Command control
- 4.1 NULL command
- 4.2 Power [PoWer]
- 4.3 Input [InPut]
- 4.4 Remote control pass-through [RemoteCode]
- 4.5 Setup [SetUp]
- 4.6 Gamma data of Gamma table “Custom 1/2/3” [GammaRed, Green, Blue]
- 4.7 Panel Alignment (zone) Data [Panel Alignment(Zone) Red, Blue]
- 4.8 Source Asking [SourCe]
- 4.9 Model status asking [MoDel]
- 4.10 Adjustment [AdjustmentCommand]
- Command code
- Parameter1
- Parameter2
- 4.10.1 Special data
- Special data
- Picture mode
- Color Profile
- Color Temp. Table Data
- Color Temp. Correction Data
- Gamma Table Data
- Gamma Correction Data
- Dynamic Control Data
- Color Management Data
- Low Latency Data
- Clear Motion Drive Data
- Motion Enhance Data
- LD Power Data
- Graphic Mode Data
- HDMI Input Level Data
- HDMI Color Space Data
- HDMI 2D/3D Data
- Aspect Data
- Mask Data
- Lens Control(Focus Near, Focus Far, Zoom Tele, Zoom Wide, Shift Left, Shift Right, Shift Up, Shift Down) Data
- Lens Image Pattern, Lens Lock, Screen Adjust, Uniformity Correction Data
- Installation Style Data
- Anamorphic Data
- Panel Alignment Switch Data
- High Altitude mode
- Back Color Data
- Menu Position Data
- Source Display
- Language Data
- Trigger Data
- Off Timer Data
- Eco Mode Data
- Control 4 Data
- Input Data
- Source Data
- Deep Color Data
- Color Space Data
- Colorimetry Data
- HDR Data
- 4.10.2 Special2 Data
- 4.10.3 Special3 Data
- 4.10.4 Special9 Data
- 4.10.5 Special10 Data
- 4.10.6 Special14 Data
- 4.10.7 Operation
- 4.10.8 Reference
- LAN setup [Lan Setup]
- Screen Codes
- Safety Precautions
4 Command control
19 / 45 PJ05030305B
4.6 Gamma data of Gamma table “Custom 1/2/3” [GammaRed, Green, Blue]
Used for sending operation of the gamma data when the Gamma table is Custom, and referencing the gamma data of the projector.
Target of switching and referencing is followed by setting value of the Gamma bank.
Command code
Table 4-11 GAMMA DATA CMD
HEX
ASCII
Function
Operation
Reference
0x47
0x52
'G' 'R'
Gamma data of the gamma table ”Custom1/2/3”
(Red) [GammaRed]
0x47 0x47
'G' 'G'
Gamma data of the gamma table ”Custom1/2/3”
(Green) [GammaGreen]
0x47
0x42
'G'
'B'
Gamma data of the gamma table ”Custom1/2/3”
(Blue) [GammaBlue]
Parameters
Data length: 512
The gamma data has 256 adjustment points composed of binary data.
The byte order is little endian.
When the projector is not powered on and it receives the command, the projector ignores the command and does not respond.
When the gamma table of the projector is not “Custom1”,”Custom2” or ”Custom3” and the projector receives the command, the
projector ignores the command and does not respond.
When the projector receives a gamma data by operation command, the projector saves the gamma data on proper area of
EEPROM immediately.
If the projector receives gamma data larger than 512 bytes, it is judged as invalid data and the projector does not respond.
The curve is combination of the curve on the OSD and the table (Normal/A/B/C/D) in the video processor.