Owner's Manual
Table Of Contents
- Instructions
- Getting Started
- Set up
- Operate
- Adjust/Set
- Maintenance
- Troubleshooting
- Others
- Quick Start Guide
- External Command Communication Specification
- 1 Outline
- 2 Interface
- 3 Protocol
- 4 Command control
- 4.1 NULL command
- 4.2 Power [PoWer]
- 4.3 Input [InPut]
- 4.4 Remote control pass-through [RemoteCode]
- 4.5 Setup [SetUp]
- 4.6 Gamma data of Gamma table “Custom 1/2/3” [GammaRed, Green, Blue]
- 4.7 Panel Alignment (zone) Data [Panel Alignment(Zone) Red, Blue]
- 4.8 Source Asking [SourCe]
- 4.9 Model status asking [MoDel]
- 4.10 Adjustment [AdjustmentCommand]
- Command code
- Parameter1
- Parameter2
- 4.10.1 Special data
- Special data
- Picture mode
- Color Profile
- Color Temp. Table Data
- Color Temp. Correction Data
- Gamma Table Data
- Gamma Correction Data
- Dynamic Control Data
- Color Management Data
- Low Latency Data
- Clear Motion Drive Data
- Motion Enhance Data
- LD Power Data
- Graphic Mode Data
- HDMI Input Level Data
- HDMI Color Space Data
- HDMI 2D/3D Data
- Aspect Data
- Mask Data
- Lens Control(Focus Near, Focus Far, Zoom Tele, Zoom Wide, Shift Left, Shift Right, Shift Up, Shift Down) Data
- Lens Image Pattern, Lens Lock, Screen Adjust, Uniformity Correction Data
- Installation Style Data
- Anamorphic Data
- Panel Alignment Switch Data
- High Altitude mode
- Back Color Data
- Menu Position Data
- Source Display
- Language Data
- Trigger Data
- Off Timer Data
- Eco Mode Data
- Control 4 Data
- Input Data
- Source Data
- Deep Color Data
- Color Space Data
- Colorimetry Data
- HDR Data
- 4.10.2 Special2 Data
- 4.10.3 Special3 Data
- 4.10.4 Special9 Data
- 4.10.5 Special10 Data
- 4.10.6 Special14 Data
- 4.10.7 Operation
- 4.10.8 Reference
- LAN setup [Lan Setup]
- Screen Codes
- Safety Precautions
4 Command control
20 / 45 PJ05030305B
4.6.1 Operation
Use the command as shown in the following examples.
Purpose: To send red gamma data of the gamma table “Custom1/2/3” to the projector.
(1) Transmit the data from the external controller to the projector as follows.
1: External controller →
0x21
0x89
0x01
0x47
0x52
0x0A
'!'(Operation)
PJ
Individual : 1
'G'
'R'
End
(2) If the projector receives the data (1) above and the command receipt is normal, an ACK is returned from the projector as follows.
2: ←Projector
0x06
0x89
0x01
0x47
0x52
0x0A
ACK
PJ
Individual : 1
'G'
'R'
End
(3) The external controller transmits 512 bytes of binary data to the projector.
(4) If the projector receives data (3) above and the command receipt was normal, an ACK is returned from the projector as follows.
4: ←Projector
0x06
0x89
0x01
0x47
0x52
0x0A
ACK
PJ
Individual : 1
'G'
'R'
End
4.6.2 Reference
Use the command as shown in the following examples.
Purpose: To confirm the green gamma data of the current gamma table “Custom3”.
(Current Gamma bank: Custom3)
(1) Transmit the data from the external controller to the projector as follows.
1: External controller →
0x3F
0x89
0x01
0x47
0x47
0x0A
'?'(Reference)
PJ
Individual : 1
'G'
'G'
End
(2) If the projector receives the data (1) above and the command receipt is normal, an ACK is returned from the projector as follows.
2: ← Projector
0x06
0x89
0x01
0x47
0x47
0x0A
ACK
PJ
Individual : 1
'G'
'G'
End
(3) The projector transmits 512 bytes binary data to the external controller.
4.7 Panel Alignment (zone) Data [Panel Alignment(Zone) Red, Blue]
Used for transmitting operation and referencing Panel Alignment (zone) data