Owner's Manual
Table Of Contents
- Instructions
- Getting Started
- Set up
- Operate
- Adjust/Set
- Maintenance
- Troubleshooting
- Others
- Quick Start Guide
- External Command Communication Specification
- 1 Outline
- 2 Interface
- 3 Protocol
- 4 Command control
- 4.1 NULL command
- 4.2 Power [PoWer]
- 4.3 Input [InPut]
- 4.4 Remote control pass-through [RemoteCode]
- 4.5 Setup [SetUp]
- 4.6 Gamma data of Gamma table “Custom 1/2/3” [GammaRed, Green, Blue]
- 4.7 Panel Alignment (zone) Data [Panel Alignment(Zone) Red, Blue]
- 4.8 Source Asking [SourCe]
- 4.9 Model status asking [MoDel]
- 4.10 Adjustment [AdjustmentCommand]
- Command code
- Parameter1
- Parameter2
- 4.10.1 Special data
- Special data
- Picture mode
- Color Profile
- Color Temp. Table Data
- Color Temp. Correction Data
- Gamma Table Data
- Gamma Correction Data
- Dynamic Control Data
- Color Management Data
- Low Latency Data
- Clear Motion Drive Data
- Motion Enhance Data
- LD Power Data
- Graphic Mode Data
- HDMI Input Level Data
- HDMI Color Space Data
- HDMI 2D/3D Data
- Aspect Data
- Mask Data
- Lens Control(Focus Near, Focus Far, Zoom Tele, Zoom Wide, Shift Left, Shift Right, Shift Up, Shift Down) Data
- Lens Image Pattern, Lens Lock, Screen Adjust, Uniformity Correction Data
- Installation Style Data
- Anamorphic Data
- Panel Alignment Switch Data
- High Altitude mode
- Back Color Data
- Menu Position Data
- Source Display
- Language Data
- Trigger Data
- Off Timer Data
- Eco Mode Data
- Control 4 Data
- Input Data
- Source Data
- Deep Color Data
- Color Space Data
- Colorimetry Data
- HDR Data
- 4.10.2 Special2 Data
- 4.10.3 Special3 Data
- 4.10.4 Special9 Data
- 4.10.5 Special10 Data
- 4.10.6 Special14 Data
- 4.10.7 Operation
- 4.10.8 Reference
- LAN setup [Lan Setup]
- Screen Codes
- Safety Precautions
4 Command control
34 / 45 PJ05030305B
Source Display
Table 4-45 Source Display CMD DATA
HEX
ASCII
Operation
0x30
‘0’
Off
0x31
‘1’
On
Language Data
Table 4-46 LANGUAGE CMD DATA
HEX
ASCII
Operation
0x30
‘0’
Japanese
0x31
‘1’
English
0x32
‘2’
German
0x33
‘3’
Spanish
0x34
‘4’
Italian
0x35
‘5’
French
0x36
‘6’
Portuguese
0x37
‘7’
Dutch
0x38
‘8’
Polski
0x39
‘9’
Norwegian
0x41
‘A’
Russian
0x42
‘B’
Chinese(Simplified Chinese)
0x43
‘C’
Chinese (Traditional Chinese)
Trigger Data
Table 4-47 TRIGGER CMD DATA
HEX
ASCII
Operation
0x30
0
Off
0x31
1
Power
0x32
2
Anamo
0x33
3
Inst. 1
0x34
4
Inst. 2
0x35
5
Inst. 3
0x36
6
Inst. 4
0x37
7
Inst. 5
0x38
8
Inst. 6
0x39
9
Inst. 7
0x41
A
Inst. 8
0x42
B
Inst. 9
0x43
C
Inst. 10
Off Timer Data
Table 4-48 OFF TIMER CMD DATA
HEX
ASCII
Operation
0x30
‘0’
Off
0x31
‘1’
1 Hour
0x32
‘2’
2 Hours
0x33
‘3’
3 Hours
0x34
‘4’
4 Hours
Eco Mode Data
Table 4-49 ECO MODE CMD DATA
HEX
ASCII
Operation