Owner's Manual
Table Of Contents
- Instructions
- Getting Started
- Set up
- Operate
- Adjust/Set
- Maintenance
- Troubleshooting
- Others
- Quick Start Guide
- External Command Communication Specification
- 1 Outline
- 2 Interface
- 3 Protocol
- 4 Command control
- 4.1 NULL command
- 4.2 Power [PoWer]
- 4.3 Input [InPut]
- 4.4 Remote control pass-through [RemoteCode]
- 4.5 Setup [SetUp]
- 4.6 Gamma data of Gamma table “Custom 1/2/3” [GammaRed, Green, Blue]
- 4.7 Panel Alignment (zone) Data [Panel Alignment(Zone) Red, Blue]
- 4.8 Source Asking [SourCe]
- 4.9 Model status asking [MoDel]
- 4.10 Adjustment [AdjustmentCommand]
- Command code
- Parameter1
- Parameter2
- 4.10.1 Special data
- Special data
- Picture mode
- Color Profile
- Color Temp. Table Data
- Color Temp. Correction Data
- Gamma Table Data
- Gamma Correction Data
- Dynamic Control Data
- Color Management Data
- Low Latency Data
- Clear Motion Drive Data
- Motion Enhance Data
- LD Power Data
- Graphic Mode Data
- HDMI Input Level Data
- HDMI Color Space Data
- HDMI 2D/3D Data
- Aspect Data
- Mask Data
- Lens Control(Focus Near, Focus Far, Zoom Tele, Zoom Wide, Shift Left, Shift Right, Shift Up, Shift Down) Data
- Lens Image Pattern, Lens Lock, Screen Adjust, Uniformity Correction Data
- Installation Style Data
- Anamorphic Data
- Panel Alignment Switch Data
- High Altitude mode
- Back Color Data
- Menu Position Data
- Source Display
- Language Data
- Trigger Data
- Off Timer Data
- Eco Mode Data
- Control 4 Data
- Input Data
- Source Data
- Deep Color Data
- Color Space Data
- Colorimetry Data
- HDR Data
- 4.10.2 Special2 Data
- 4.10.3 Special3 Data
- 4.10.4 Special9 Data
- 4.10.5 Special10 Data
- 4.10.6 Special14 Data
- 4.10.7 Operation
- 4.10.8 Reference
- LAN setup [Lan Setup]
- Screen Codes
- Safety Precautions
4 Command control
38 / 45 PJ05030305B
4.10.7 Operation
Use the command as shown in the following examples.
(Example 1) Switching Picture Mode
Purpose: To set Color Temp. Table to ‘6500K’
(1) Transmitting Data from External controller to Projector as follows.
1: External Controller
→
0x21
0x89
0x01
0x50
0x4D
0x43
0x4C
0x32
0x0A
'!'
（
Operation）
PJ
Individual : 1
‘P’
‘M’
‘C’
‘L’
6500K
End
(2) If the projector receives the data (1) above and the command receipt is normal, an ACK is returned from the projector as follows.
2:
←
Projector
0x06
0x89
0x01
0x50
0x4D
0x0A
ACK
PJ
Individual : 1
‘P’
‘M’
End
(3) The projector sets the Color Temp. Table to ‘6500K’.
(Example 2) Contrast adjustment
Purpose: To set Contrast to +20.
(1) Transmit the data from the external controller to the projector as follows.
1: External controller →
0x21
0x89
0x01
0x50
0x4D
0x43
0x4E
0x30
0x30
0x31
0x34
0x0A
'!'(Operation)
PJ
Individual : 1
‘P’
‘M’
‘C’
‘N’
‘0’
‘0’
‘1’
‘4’
End
(2) If the projector receives the data (1) above and the command receipt is normal, an ACK is returned from the projector as follows.
2: ←Projector
0x06
0x89
0x01
0x50
0x4D
0x0A
ACK
PJ
Individual : 1
‘P’
‘M’
End
(3) The projector sets the contrast to +20.