Owner's Manual
Table Of Contents
- Instructions
- Getting Started
- Set up
- Operate
- Adjust/Set
- Maintenance
- Troubleshooting
- Others
- Quick Start Guide
- External Command Communication Specification
- 1 Outline
- 2 Interface
- 3 Protocol
- 4 Command control
- 4.1 NULL command
- 4.2 Power [PoWer]
- 4.3 Input [InPut]
- 4.4 Remote control pass-through [RemoteCode]
- 4.5 Setup [SetUp]
- 4.6 Gamma data of Gamma table “Custom 1/2/3” [GammaRed, Green, Blue]
- 4.7 Panel Alignment (zone) Data [Panel Alignment(Zone) Red, Blue]
- 4.8 Source Asking [SourCe]
- 4.9 Model status asking [MoDel]
- 4.10 Adjustment [AdjustmentCommand]
- Command code
- Parameter1
- Parameter2
- 4.10.1 Special data
- Special data
- Picture mode
- Color Profile
- Color Temp. Table Data
- Color Temp. Correction Data
- Gamma Table Data
- Gamma Correction Data
- Dynamic Control Data
- Color Management Data
- Low Latency Data
- Clear Motion Drive Data
- Motion Enhance Data
- LD Power Data
- Graphic Mode Data
- HDMI Input Level Data
- HDMI Color Space Data
- HDMI 2D/3D Data
- Aspect Data
- Mask Data
- Lens Control(Focus Near, Focus Far, Zoom Tele, Zoom Wide, Shift Left, Shift Right, Shift Up, Shift Down) Data
- Lens Image Pattern, Lens Lock, Screen Adjust, Uniformity Correction Data
- Installation Style Data
- Anamorphic Data
- Panel Alignment Switch Data
- High Altitude mode
- Back Color Data
- Menu Position Data
- Source Display
- Language Data
- Trigger Data
- Off Timer Data
- Eco Mode Data
- Control 4 Data
- Input Data
- Source Data
- Deep Color Data
- Color Space Data
- Colorimetry Data
- HDR Data
- 4.10.2 Special2 Data
- 4.10.3 Special3 Data
- 4.10.4 Special9 Data
- 4.10.5 Special10 Data
- 4.10.6 Special14 Data
- 4.10.7 Operation
- 4.10.8 Reference
- LAN setup [Lan Setup]
- Screen Codes
- Safety Precautions
4 Command control
42 / 45 PJ05030305B
LAN setup [Lan Setup]
Used to setup LAN configuration.
Command code
Table 4-58 LAN SETUP CMD
HEX
ASCII
Function
0x4C
0x53
'L'
'S'
LAN setup [Lan Setup]
Parameter1
Data length: No regulation
Sub command table (Mandatory command only)
Table 4-59 LAN SETUP CMD SUB
HEX
ASCII Function
Last
memory
Operation Reference
0x44 0x53
'D'
'S'
DHCP Client setting
Yes
0x49 0x50
‘I’
‘P’
IP Address setting
Yes
(When ‘DHCP Client’ is Off.)
0x53
0x4D
‘S’
‘M’
Subnet Mask setting
Yes
(When ‘DHCP Client’ is Off.)
0x44 0x47
‘D’
‘G’
Default Gateway setting
Yes
(When ‘DHCP Client’ is Off.)
0x4D
0x41
‘M’
‘A’
MAC Address setting
Yes
-
0x52
0x53
‘R’
‘S’
Network reboot
No
-
0x50
0x54
‘P’
‘T’
Port setting Yes
It consists of “Sub command” + “setting”. Sub command consists of ASCII character 2 bytes.
Parameter2
Sub command parameters are as follows.
Parameters when Sub command is [0x44,0x53]: Data length 1
Table 4-60 DHCP Client
HEX
ASCII
Operation
0x30
‘0’
Off(Static)
0x31
‘1’
On
Parameters when Sub command is [0x49,0x50] [0x53,0x4D] [0x44,0x47]: Data length 8
Parameters when Sub command is [0x4D,0x41]: Data length 12
Parameters when Sub command is [0x52,0x53]: Data length 1
Table 4-61 NETWORK RESTART
HEX
ASCII
Operation
0x31
‘1’
Network Restart
Parameters when Sub command is [0x50,0x54]: Data length 4