Owner's Manual
Table Of Contents
- Instructions
- Getting Started
- Set up
- Operate
- Adjust/Set
- Maintenance
- Troubleshooting
- Others
- Quick Start Guide
- External Command Communication Specification
- 1 Outline
- 2 Interface
- 3 Protocol
- 4 Command control
- 4.1 NULL command
- 4.2 Power [PoWer]
- 4.3 Input [InPut]
- 4.4 Remote control pass-through [RemoteCode]
- 4.5 Setup [SetUp]
- 4.6 Gamma data of Gamma table “Custom 1/2/3” [GammaRed, Green, Blue]
- 4.7 Panel Alignment (zone) Data [Panel Alignment(Zone) Red, Blue]
- 4.8 Source Asking [SourCe]
- 4.9 Model status asking [MoDel]
- 4.10 Adjustment [AdjustmentCommand]
- Command code
- Parameter1
- Parameter2
- 4.10.1 Special data
- Special data
- Picture mode
- Color Profile
- Color Temp. Table Data
- Color Temp. Correction Data
- Gamma Table Data
- Gamma Correction Data
- Dynamic Control Data
- Color Management Data
- Low Latency Data
- Clear Motion Drive Data
- Motion Enhance Data
- LD Power Data
- Graphic Mode Data
- HDMI Input Level Data
- HDMI Color Space Data
- HDMI 2D/3D Data
- Aspect Data
- Mask Data
- Lens Control(Focus Near, Focus Far, Zoom Tele, Zoom Wide, Shift Left, Shift Right, Shift Up, Shift Down) Data
- Lens Image Pattern, Lens Lock, Screen Adjust, Uniformity Correction Data
- Installation Style Data
- Anamorphic Data
- Panel Alignment Switch Data
- High Altitude mode
- Back Color Data
- Menu Position Data
- Source Display
- Language Data
- Trigger Data
- Off Timer Data
- Eco Mode Data
- Control 4 Data
- Input Data
- Source Data
- Deep Color Data
- Color Space Data
- Colorimetry Data
- HDR Data
- 4.10.2 Special2 Data
- 4.10.3 Special3 Data
- 4.10.4 Special9 Data
- 4.10.5 Special10 Data
- 4.10.6 Special14 Data
- 4.10.7 Operation
- 4.10.8 Reference
- LAN setup [Lan Setup]
- Screen Codes
- Safety Precautions
Adjusting to the Preferred Color (Color Management)
Based on the setting of the selected “Color Profile”, you can adjust each of the following colors according to your
preference: Red, Yellow, Green, Cyan, Blue, and Magenta.
1
Press the [ADVANCED MENU] button to display the “Color Profile” menu
2
Set “Color Management” to “On”, and press the [OK]
button
0
You can also perform setting from “Picture Adjust”"“Color
Profile”"“Color Management” in the menu.
3
Adjust to the preferred color
A
Select “Color Selection”, and press the H I
keys to
select the color to adjust
0
For color adjustment, select the color from the
following:
“Red”, “Yellow”, “Green”, “Cyan”, “Blue”,
“Magenta”.
B
Adjust the selected color
Item
Setting Range
Description
Axis Position -30 to 30 Fine-tune the position
of the central axis of
the selected color.
Hue -30 to 30 Adjusts the hue (color
tone).
Saturation -30 to 30 Adjusts the color
saturation (vividness).
-30 (dull) to +30 (vivid)
Brightness -30 to 30 Adjusts the
brightness.
-30 (dark) to +30
(bright)
0
Selecting “Reset” resets all the adjustment data.
0
Pressing
the [HIDE] button on the remote control
enables you to check the image before
adjustment. Press the [HIDE] button again to
return to the adjustment screen.
4
Press the [MENU] button to exit
0
0
0
0
HIDE
Red
On
Film 1
Before
Brightness
Saturation
Hue
Axis Position
Color Selection
Color Management
Color Profile
Color Profile
Reset
On
Off
0
0
0
0
HIDE
A
B
MagentaBlue
Cyan
Green Yellow
Red
Clockwise rotation: -
Counterclockwise rotation: +
Axis Position (Image)
Adjustable range when
Red is selected: ± 30°
with Red as the center
Red
On
Film 1
Before
Brightness
Saturation
Hue
Axis Position
Color Selection
Color Management
Color Profile
Color Profile
Reset
34
Adjust/Set