Owner's Manual
Table Of Contents
- Instructions
- Getting Started
- Set up
- Operate
- Adjust/Set
- Maintenance
- Troubleshooting
- Others
- Quick Start Guide
- External Command Communication Specification
- 1 Outline
- 2 Interface
- 3 Protocol
- 4 Command control
- 4.1 NULL command
- 4.2 Power [PoWer]
- 4.3 Input [InPut]
- 4.4 Remote control pass-through [RemoteCode]
- 4.5 Setup [SetUp]
- 4.6 Gamma data of Gamma table “Custom 1/2/3” [GammaRed, Green, Blue]
- 4.7 Panel Alignment (zone) Data [Panel Alignment(Zone) Red, Blue]
- 4.8 Source Asking [SourCe]
- 4.9 Model status asking [MoDel]
- 4.10 Adjustment [AdjustmentCommand]
- Command code
- Parameter1
- Parameter2
- 4.10.1 Special data
- Special data
- Picture mode
- Color Profile
- Color Temp. Table Data
- Color Temp. Correction Data
- Gamma Table Data
- Gamma Correction Data
- Dynamic Control Data
- Color Management Data
- Low Latency Data
- Clear Motion Drive Data
- Motion Enhance Data
- LD Power Data
- Graphic Mode Data
- HDMI Input Level Data
- HDMI Color Space Data
- HDMI 2D/3D Data
- Aspect Data
- Mask Data
- Lens Control(Focus Near, Focus Far, Zoom Tele, Zoom Wide, Shift Left, Shift Right, Shift Up, Shift Down) Data
- Lens Image Pattern, Lens Lock, Screen Adjust, Uniformity Correction Data
- Installation Style Data
- Anamorphic Data
- Panel Alignment Switch Data
- High Altitude mode
- Back Color Data
- Menu Position Data
- Source Display
- Language Data
- Trigger Data
- Off Timer Data
- Eco Mode Data
- Control 4 Data
- Input Data
- Source Data
- Deep Color Data
- Color Space Data
- Colorimetry Data
- HDR Data
- 4.10.2 Special2 Data
- 4.10.3 Special3 Data
- 4.10.4 Special9 Data
- 4.10.5 Special10 Data
- 4.10.6 Special14 Data
- 4.10.7 Operation
- 4.10.8 Reference
- LAN setup [Lan Setup]
- Screen Codes
- Safety Precautions
Whole Adjust (Pixel) Operation Procedure
For making general adjustments to slight color fringing in the horizontal/vertical directions of the video image.
A
Set “Adjust Area” to “Whole”
B
Select “Adjust Color” and “Adjust Pattern Color”
C
Select “Adjust (Pixel)”, and press the [OK] button
0
The Adjustment mode is activated, and the selected adjustment pattern and Adjustment (Pixel) window are
displayed.
.
Color A.
BACK
GAMMA
Adjust. Color P. A. Area
COLOR
TEMP
3D
FORMAT
PIC.
ADJ.
H 0
V 0
Red
Pixel Adjust
Back
Whole Adjust (Pixel)
V (Vertical)
H (Horizontal)
Adjustment (Pixel) Window
Adjustment Pattern
D
Use the [JKH I] keys to move and adjust the vertical and horizontal pixels of the entire zone
0
The adjustment setting appears at the center of the Adjustment (Pixel) window.
.
Color A.
BACK
GAMMA
Adjust. Color P. A. Area
COLOR
TEMP
3D
FORMAT
PIC.
ADJ.
H 0
V 0
Red
Pixel Adjust
Back
Whole Adjust (Pixel)
Remote Control Operation
Guide
Color for
Adjustment
Pixel Adjustment Setting
E
After adjustment is complete, press the [BACK] button twice to exit the Adjustment mode
Remote Control Operation Guide
Button Name Function Description of Operation
[GAMMA] Color A. Changes “Adjust Color”.
[COLOR TEMP.] Adjust Switches between “Adjust (Pixel)” and “Adjust (Fine)”.
0
Switches to “Adjust (Pixel)” when “Adjust Area” is set to “Zone”.
[3D FORMAT] Color P. Changes “Adjust Pattern Color”.
[PIC ADJ.] A. Area Switches “Adjust Area”.
0
A zone cursor appears on the adjustment pattern when the “Zone”
setting is selected.
53
Adjust/Set