Owner's Manual
Table Of Contents
- Instructions
- Getting Started
- Set up
- Operate
- Adjust/Set
- Maintenance
- Troubleshooting
- Others
- Quick Start Guide
- External Command Communication Specification
- 1 Outline
- 2 Interface
- 3 Protocol
- 4 Command control
- 4.1 NULL command
- 4.2 Power [PoWer]
- 4.3 Input [InPut]
- 4.4 Remote control pass-through [RemoteCode]
- 4.5 Setup [SetUp]
- 4.6 Gamma data of Gamma table “Custom 1/2/3” [GammaRed, Green, Blue]
- 4.7 Panel Alignment (zone) Data [Panel Alignment(Zone) Red, Blue]
- 4.8 Source Asking [SourCe]
- 4.9 Model status asking [MoDel]
- 4.10 Adjustment [AdjustmentCommand]
- Command code
- Parameter1
- Parameter2
- 4.10.1 Special data
- Special data
- Picture mode
- Color Profile
- Color Temp. Table Data
- Color Temp. Correction Data
- Gamma Table Data
- Gamma Correction Data
- Dynamic Control Data
- Color Management Data
- Low Latency Data
- Clear Motion Drive Data
- Motion Enhance Data
- LD Power Data
- Graphic Mode Data
- HDMI Input Level Data
- HDMI Color Space Data
- HDMI 2D/3D Data
- Aspect Data
- Mask Data
- Lens Control(Focus Near, Focus Far, Zoom Tele, Zoom Wide, Shift Left, Shift Right, Shift Up, Shift Down) Data
- Lens Image Pattern, Lens Lock, Screen Adjust, Uniformity Correction Data
- Installation Style Data
- Anamorphic Data
- Panel Alignment Switch Data
- High Altitude mode
- Back Color Data
- Menu Position Data
- Source Display
- Language Data
- Trigger Data
- Off Timer Data
- Eco Mode Data
- Control 4 Data
- Input Data
- Source Data
- Deep Color Data
- Color Space Data
- Colorimetry Data
- HDR Data
- 4.10.2 Special2 Data
- 4.10.3 Special3 Data
- 4.10.4 Special9 Data
- 4.10.5 Special10 Data
- 4.10.6 Special14 Data
- 4.10.7 Operation
- 4.10.8 Reference
- LAN setup [Lan Setup]
- Screen Codes
- Safety Precautions
Striped patterns appear on the screen
Check Action Refer to
Does the fabric of the screen have a
regular pattern?
Interference fringes may sometimes occur between the
fabric
pattern and the pixels. Please consult the authorized
dealer.
—
Video images are missing
Check Action Refer to
Has screen mask been configured? Set “Mask” to “Off”. P. 56
Remote control does not work
Check Action Refer to
Are the batteries correctly loaded? Match the polarities (t s) correctly when loading the
batteries.
P. 15
Are the batteries exhausted? Replace with new batteries. P. 15
Is there an obstructing object between
the remote control and remote sensor?
Remove any obstructing object. P. 15
Is the remote control held too far away
from the unit?
Hold the remote control closer to the sensor during use. P. 15
Are the IR (infrared) 3D GLASSES and
3D SYNCHRO EMITTER in use?
As there is a possibility of signal interference, when you are
using the IR (infrared) 3D GLASSES together with the 3D
SYNCHRO EMITTER, try adjusting the orientation of the
3D SYNCHRO EMITTER.
P. 29
Noise is heard
Check Action Refer to
Is the exhaust vent blocked?
Is the unit used near a heater or air-
conditioner?
Check the installation condition of the projector.
When
the surrounding temperature of the projector is high,
the fan revolution speed increases to protect the projector
unit, hence a louder operating sound.
P. 17
Is “LD Power” set to “High”? Setting “LD Power” to “High” increases the fan rotation
speed, and noise would be louder as a result.
P. 44
There are small black or colored dots on the screen
The D-ILA device is manufactured using high-precision technologies, but there may be some (less than 0.01%) missing
pixels or pixels that remain permanently lit. This is not a malfunction.
65
Troubleshooting