Owner's Manual
Table Of Contents
- Instructions
- Getting Started
- Set up
- Operate
- Adjust/Set
- Maintenance
- Troubleshooting
- Others
- Quick Start Guide
- External Command Communication Specification
- 1 Outline
- 2 Interface
- 3 Protocol
- 4 Command control
- 4.1 NULL command
- 4.2 Power [PoWer]
- 4.3 Input [InPut]
- 4.4 Remote control pass-through [RemoteCode]
- 4.5 Setup [SetUp]
- 4.6 Gamma data of Gamma table “Custom 1/2/3” [GammaRed, Green, Blue]
- 4.7 Panel Alignment (zone) Data [Panel Alignment(Zone) Red, Blue]
- 4.8 Source Asking [SourCe]
- 4.9 Model status asking [MoDel]
- 4.10 Adjustment [AdjustmentCommand]
- Command code
- Parameter1
- Parameter2
- 4.10.1 Special data
- Special data
- Picture mode
- Color Profile
- Color Temp. Table Data
- Color Temp. Correction Data
- Gamma Table Data
- Gamma Correction Data
- Dynamic Control Data
- Color Management Data
- Low Latency Data
- Clear Motion Drive Data
- Motion Enhance Data
- LD Power Data
- Graphic Mode Data
- HDMI Input Level Data
- HDMI Color Space Data
- HDMI 2D/3D Data
- Aspect Data
- Mask Data
- Lens Control(Focus Near, Focus Far, Zoom Tele, Zoom Wide, Shift Left, Shift Right, Shift Up, Shift Down) Data
- Lens Image Pattern, Lens Lock, Screen Adjust, Uniformity Correction Data
- Installation Style Data
- Anamorphic Data
- Panel Alignment Switch Data
- High Altitude mode
- Back Color Data
- Menu Position Data
- Source Display
- Language Data
- Trigger Data
- Off Timer Data
- Eco Mode Data
- Control 4 Data
- Input Data
- Source Data
- Deep Color Data
- Color Space Data
- Colorimetry Data
- HDR Data
- 4.10.2 Special2 Data
- 4.10.3 Special3 Data
- 4.10.4 Special9 Data
- 4.10.5 Special10 Data
- 4.10.6 Special14 Data
- 4.10.7 Operation
- 4.10.8 Reference
- LAN setup [Lan Setup]
- Screen Codes
- Safety Precautions
Communications Example
This section shows the communication examples of RS-232C.
Operating command
Type Command Description
Connection check PC "
This unit: 21 89 01 00 00 0A
This unit " PC: 06 89 01 00 00 0A
Connection check
Power (On) PC "
This unit: 21 89 01 50 57 31 0A
This unit " PC: 06 89 01 50 57 0A
When power is turned on from the
Standby mode
Power (Off) PC "
This unit: 21 89 01 50 57 30 0A
This unit " PC: 06 89 01 50 57 0A
When power is turned off (Standby
mode) from power-on mode
Remote control
(MENU)
PC "
This unit: 21 89 01 52 43 37 33 32 45 0A
This unit " PC: 06 89 01 52 43 0A
When the same operation as
pressing the [MENU] button on the
remote control is performed
Reference command
Type Command Description
Power (On) PC "
This unit: 3F 89 01 50 57 0A
This unit " PC: 06 89 01 50 57 0A
This unit " PC: 40 89 01 50 57 31 0A
When information on the power-on
state is acquired
Input (HDMI 1) PC " This unit: 3F 89 01 49 50 0A
This unit " PC: 06 89 01 49 50 0A
This unit " PC: 40 89 01 49 50 36 0A
When information on HDMI 1 input
is acquired
70
Others