Owner's Manual
Table Of Contents
- Instructions
- Getting Started
- Set up
- Operate
- Adjust/Set
- Maintenance
- Troubleshooting
- Others
- Quick Start Guide
- External Command Communication Specification
- 1 Outline
- 2 Interface
- 3 Protocol
- 4 Command control
- 4.1 NULL command
- 4.2 Power [PoWer]
- 4.3 Input [InPut]
- 4.4 Remote control pass-through [RemoteCode]
- 4.5 Setup [SetUp]
- 4.6 Gamma data of Gamma table “Custom 1/2/3” [GammaRed, Green, Blue]
- 4.7 Panel Alignment (zone) Data [Panel Alignment(Zone) Red, Blue]
- 4.8 Source Asking [SourCe]
- 4.9 Model status asking [MoDel]
- 4.10 Adjustment [AdjustmentCommand]
- Command code
- Parameter1
- Parameter2
- 4.10.1 Special data
- Special data
- Picture mode
- Color Profile
- Color Temp. Table Data
- Color Temp. Correction Data
- Gamma Table Data
- Gamma Correction Data
- Dynamic Control Data
- Color Management Data
- Low Latency Data
- Clear Motion Drive Data
- Motion Enhance Data
- LD Power Data
- Graphic Mode Data
- HDMI Input Level Data
- HDMI Color Space Data
- HDMI 2D/3D Data
- Aspect Data
- Mask Data
- Lens Control(Focus Near, Focus Far, Zoom Tele, Zoom Wide, Shift Left, Shift Right, Shift Up, Shift Down) Data
- Lens Image Pattern, Lens Lock, Screen Adjust, Uniformity Correction Data
- Installation Style Data
- Anamorphic Data
- Panel Alignment Switch Data
- High Altitude mode
- Back Color Data
- Menu Position Data
- Source Display
- Language Data
- Trigger Data
- Off Timer Data
- Eco Mode Data
- Control 4 Data
- Input Data
- Source Data
- Deep Color Data
- Color Space Data
- Colorimetry Data
- HDR Data
- 4.10.2 Special2 Data
- 4.10.3 Special3 Data
- 4.10.4 Special9 Data
- 4.10.5 Special10 Data
- 4.10.6 Special14 Data
- 4.10.7 Operation
- 4.10.8 Reference
- LAN setup [Lan Setup]
- Screen Codes
- Safety Precautions
Specifications
Product Name D-ILA Projector
Model Name DLA-RS4500
Display Panel/Size D-ILA device *1, 2
0.69” 4K D-ILA (4096 x 2160 pixels) x 3
Projection Lens 2.0 x power zoom lens (1.4:1 to 2.8:1), motorized zoom and focus
Light Source BLU-Escent (Laser Diode)
Screen Size Approx. 60” to 280” (Aspect ratio of 16:9)
Brightness 3000 lm
Projection Distance Refer to P. 73.
Input Compatibility Signal Refer to P. 75.
Display Resolution 4096 x 2160 pixels
Input Terminal HDMI Input Dual, HDMI 19-pin x 2 (HDCP 2.2-compatible) *3
Output Terminal Trigger Terminal Single, Ø 3.5 mm DC Power Jack (E)
DC OUT 12 V, 0.1 A
3D synchro Dedicated terminal for 3D SYNCHRO EMITTER (single, mini-DIN 3-
pin)
Control Terminal RS-232C Terminal Single, D-sub 9-pin (male) (external control)
LAN Terminal Single, RJ-45 plug
Service
Terminal
SERVICE Single (USB Type A) *4
Power Requirements AC 100 V to 240 V, 50 Hz/60 Hz
Power Consumption 750 W (during normal standby: 1.5 W *5, during Eco Mode standby:
0.4 W *6)
Operation Environment Temperature: 5°C to 35°C; humidity: 20% to 80%; storage
temperature: -10°C to 60
°C
Installation Height Below 5,000 ft (1524 m)
Dimensions (Width x Height x Depth) 500 mm x 235 mm x 720 mm (19.685 in x 9.25 in x 28.3 in) (including
feet)
Mass 37.5 kg (82.7lb)
Accessories Refer to P. 10.
*1 D-ILA is the abbreviation for Direct Drive Image Light Amplifier.
*2 D-ILA
devices are manufactured using extremely high-precision technology with a pixel effectiveness of 99.99%.
Only 0.01% or less of the pixels are either missing or would remain permanently lit.
*3 HDCP is the abbreviation for High-bandwidth Digital Content Protection system. The image of the HDMI input
terminal may not be displayed in some cases due to changes in the HDCP specifications.
*4 Exclusively for firmware update.
*5 The power consumption of this product during networked standby when all wired network ports are connected
is 1.5 W.
*6 “During standby” refers to Eco Mode standby (P. 58).
0
Design and specifications are subject to change without prior notice.
0
Please
note that some of the pictures and illustrations may have been abridged, enlarged or contextualized in order
to aid comprehension. Images may differ from the actual product.
71
Others