Filename [DR-M7EK_02Cov1.fm] DR-M7EK_01.
Filename [DR-M7EK_03Safety.fm] Masterpage:Left0 DR-M7EK_03Safety.fm Page 2 Friday, April 2, 2004 3:35 PM 2 Safety Precautions The rating plate and the safety caution are on the rear of the unit. WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. CAUTION A UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED.
Filename [DR-M7EK_03Safety.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 3 Friday, April 2, 2004 11:21 AM 3 MOISTURE CONDENSATION The STANDBY/ON 1 button does not completely shut off mains power from the unit, but switches operating current on and off. “`” shows electrical power standby and “!” shows ON. When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both sides, on top and at the rear).
Filename [DR-M7EK_03Safety.fm] DR-M7EK_01.book Page 4 Friday, April 2, 2004 11:21 AM 4 Masterpage:Left+ SAFETY FIRST (cont.) Some Do’s And Don’ts On The Safe Use Of Equipment This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. DO read the operating instructions before you attempt to use the equipment.
Filename [DR-M7EK_01TOC.fm] Masterpage:Right DR-M7EK_01.book Page 5 Friday, April 2, 2004 11:21 AM 5 CONTENTS SAFETY FIRST 2 Safety Precautions ............................................... 2 Some Do’s And Don’ts On The Safe Use Of Equipment ........................................................ 4 DISC INFORMATION 6 About Discs ......................................................... 6 INDEX 11 INSTALLING YOUR NEW UNIT 17 Check Contents .................................................
Filename [DR-M7EK_05DiscInfo.fm] Masterpage:Left0 DR-M7EK_01.book Page 6 Friday, April 2, 2004 11:21 AM 6 DISC INFORMATION About Discs Recordable/playable discs You can use discs with the following logos for recording and playback. DVD-RAM DVD-R 12 cm: 4.7 GB/9.4 GB 8 cm: 1.4 GB/2.8 GB (VR mode) Version 2.0 Version 2.1 12 cm: 4.7 GB 8 cm: 1.4 GB General Version 2.0 (Video mode) DVD-RW 12 cm: 4.7 GB Version 1.0 (VR mode) Version 1.
Filename [DR-M7EK_05DiscInfo.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 7 Friday, April 2, 2004 11:21 AM 7 Discs for Playback Only Unplayable Discs You can use discs with the following logos for playback only. The following types of discs cannot be played using this unit. Do not attempt to play back any kind of disc that is damaged (cracked, warped, or repaired with adhesive tape) or discs in unusual shapes (heart-shaped, octagonal, or other forms).
Filename [DR-M7EK_05DiscInfo.fm] Masterpage:Left+ DR-M7EK_01.book Page 8 Friday, April 2, 2004 11:21 AM 8 DISC INFORMATION (cont.) Recording Medium and Format File Structure of Discs DVD-RAM DVD VIDEO ● Recording and erasing can be performed as many times as possible on a disc. ● Editing can be performed after recording, such as deleting unwanted parts.
Filename [DR-M7EK_05DiscInfo.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 9 Friday, April 2, 2004 11:21 AM 9 JPEG/MP3 Disc (CD-R/RW/ROM) MP3/JPEG files put in directories nested in several levels on a disc will be organized as if they were put in single level directories (groups) by the MP3/JPEG Navigation of this unit. (墌 pg.
Filename [DR-M7EK_05DiscInfo.fm] Masterpage:Left+ DR-M7EK_05DiscInfo.fm Page 10 Friday, April 2, 2004 3:26 PM 10 DISC INFORMATION (cont.) Placing a Disc Care and Handling of Discs Opening the disc tray Press x on the unit or remote control to open the disc tray. REC MODE LIVE CHECK OPEN/ SET UP DISPLAY ON SCREEN CLOSE REC MODE SAT# VIDEO AUDIO SUBTITLE ANGLE PROGRESSIVE SCAN DV S-VIDEO VIDEO DV IN L(MONO)-AUDIO-R Unit When handling a disc, do not touch the surface of the disc.
Filename [DR-M7EK_06Name.fm] Masterpage:Right0 DR-M7EK_01.book Page 11 Friday, April 2, 2004 11:21 AM 11 INDEX FRONT VIEW A B C D E FGH I J REC MODE SAT# VIDEO 1 STANDBY/ON F1 DV S-VIDEO K L A Infrared Beam Receiving Window B Front Display Panel 墌 pg. 13 C Disc Tray D Open/Close Button (x (OPEN/CLOSE)) 墌 pg. 10 E Automatic Satellite Programme Recording Button (SAT#) 墌 pg. 65 F Stop Button (8) 墌 pg. 31, 53 G Play Button (4 (PLAY)) 墌 pg. 31 H Pause Button (9 (PAUSE)) 墌 pg.
Filename [DR-M7EK_06Name.fm] Masterpage:Left+ DR-M7EK_06Name.fm Page 12 Friday, April 2, 2004 3:27 PM 12 INDEX (cont.) REAR VIEW A Antenna Input Connector (ANTENNA IN) 墌 pg. 18 B Component Video Output Connectors (COMPONENT VIDEO OUT )墌 pg. 20 C S-video Output Connector (S-VIDEO OUT) 墌 pg. 19 D Audio Output Connectors (AUDIO OUT (RIGHT/LEFT)) 墌 pg. 19 E AV COMPU LINK Connector* * Not function with this unit. F Digital Audio Output Connectors (DIGITAL OUT (COAXIAL/OPTICAL)) 墌 pg.
Filename [DR-M7EK_06Name.fm] DR-M7EK_01.book Page 13 Friday, April 2, 2004 11:21 AM Masterpage:Right-No-Heading 13 FRONT DISPLAY PANEL A VPS/PDC Indicator* 墌 pg. 59 Appears when checking if the station being received transmits a VPS/PDC signal. * VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this unit. Disc Type/Status Indicator When a disc is loaded, the type of the disc is indicated. When a disc is running, the disc marks rotate.
Filename [DR-M7EK_06Name.fm] DR-M7EK_01.book Page 14 Friday, April 2, 2004 11:21 AM 14 INDEX (cont.) G Simulated Surround Effect Indicator (3D) 墌 pg. 46 Lights when a simulated surround effect is set to “3D-ON” in Play Set Up menu. H Linear PCM Indicator (LPCM) Lights when “XP MODE REC AUDIO” is set to “LINEAR PCM” (墌 pg. 92) for recording with DVD-RAM, DVD-R and DVD-RW discs, and when Linear PCM audio is played. I Random/Programme Playback Mode Indicator (RND/PRGM) 墌 pg.
Filename [DR-M7EK_06Name.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 15 Friday, April 2, 2004 11:21 AM 15 ON-SCREEN DISPLAY When “SUPERIMPOSE” is set to “AUTO” and ON SCREEN on the remote control is pressed, various operational indicators appear on the TV screen. To clear the operational indicators, press ON SCREEN again. A Disc Display Displays the type of the disc loaded on the disc tray. B Title Number* Displays number of the title currently being played back.
Filename [DR-M7EK_06Name.fm] Masterpage:Left+ DR-M7EK_01.book Page 16 Friday, April 2, 2004 11:21 AM 16 INDEX (cont.
Filename [DR-M7EK_06Name.fm] Masterpage:Right0 DR-M7EK_06Name.
Filename [DR-M7EK_06Name.fm] Masterpage:Left+ DR-M7EK_01.book Page 18 Friday, April 2, 2004 11:21 AM 18 INSTALLING YOUR NEW UNIT (cont.) Basic Connections Aerial connector Back of TV It’s essential that your unit be properly connected. THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED. A Install the unit. Place the unit on a stable, horizontal surface. B Connect the unit to a TV.
Filename [DR-M7EK_06Name.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 19 Friday, April 2, 2004 11:21 AM 19 8 To connect to TV’s S-VIDEO input and AUDIO input connectors S-VIDEO Connection A Connect the unit to a TV. A Connect the aerial, unit and TV as per “Basic Connections”. (墌 pg. 18) B Connect the unit’s S-VIDEO OUT connector to the TV’s S-VIDEO input connector. C Connect the unit’s AUDIO OUT connectors to the TV’s AUDIO input connectors. B Connect the unit to mains.
Filename [DR-M7EK_06Name.fm] Masterpage:Left+ DR-M7EK_01.book Page 20 Friday, April 2, 2004 11:21 AM 20 INSTALLING YOUR NEW UNIT (cont.) Component Video Connection TV aerial cable 8 To connect to TV’s component video input connectors A Connect the unit to TV. A Perform A – C in step B in “Basic Connections” (墌 pg. 18). B Connect the unit’s COMPONENT VIDEO OUT connectors to the TV’s component video input connectors. C Connect the unit’s AUDIO OUT connectors to the TV’s AUDIO input connectors.
Filename [DR-M7EK_06Name.fm] Masterpage:Right0 DR-M7EK_01.book Page 21 Friday, April 2, 2004 11:21 AM 21 INITIAL SETTINGS Auto Set Up Before starting, make sure of the following: ● The TV aerial cable should be connected to the unit. ● The unit’s mains power cord should be connected to a mains outlet. ● Turn on the TV and select the AV mode. ● Slide the TV/CABLE/SAT/DVD switch to DVD. Auto Channel Set/Auto Clock Set/ Auto Guide Program Number Set A Turn on the unit.
Filename [DR-M7EK_06Name.fm] DR-M7EK_01.book Page 22 Friday, April 2, 2004 11:21 AM 22 Masterpage:Left+ INITIAL SETTINGS (cont.) ATTENTION: Once you have performed Auto Set Up, even if the unit’s memory backup has expired, all the stored stations and their Guide Program numbers remain in the unit’s memory and the unit will not perform Auto Set Up again. The unit only performs Auto Clock Set when the unit is turned on. If you have moved to a different area, perform each setting as required.
Filename [DR-M7EK_06Name.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 23 Friday, April 2, 2004 11:21 AM 23 Preset Download Auto Channel Set by Downloading from TV/Auto Clock Set/Auto Guide Program Number Set ATTENTION: You can use this function only with a TV offering T-V Link, etc.* Be sure to use a fully-wired 21-pin SCART cable. * Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link or DATA LOGIC via a fully-wired 21-pin SCART cable.
Filename [DR-M7EK_06Name.fm] Masterpage:Left+ DR-M7EK_01.book Page 24 Friday, April 2, 2004 11:21 AM 24 INITIAL SETTINGS (cont.) Results of Auto Set Up/Preset Download appearing on the front display panel If both Auto Channel Set and Auto Clock Set have been performed successfully, the correct current time is displayed. Turn on the TV and select its AV mode, then make sure that all necessary stations have been stored in the unit’s memory by using the PR +/– button(s). ● If station names (ID – 墌 pg.
Filename [DR-M7EK_06Name.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 25 Friday, April 2, 2004 11:21 AM 25 Monitor Set You can select the monitor type depending on the TV used when you play back DVD VIDEO discs recorded for wide-screen TVs. ● Turn on the unit. ● Turn on the TV and select the AV mode. ● Slide the TV/CABLE/SAT/DVD switch to DVD. A Access the Main Menu screen. Press SET UP. B Access the “VIDEO IN/OUT” screen. A Press w e to move the arrow to “FUNCTION SET UP”, then press ENTER.
Filename [DR-M7EK_06Name.fm] Masterpage:Left+ DR-M7EK_01.book Page 26 Friday, April 2, 2004 11:21 AM 26 INITIAL SETTINGS (cont.) C Select the desired language. Language A Press rt to move the arrow to “ON SCREEN LANGUAGE”, then press ENTER. B Press rt to select your desired language, then press ENTER. ● Turn on the unit. ● Turn on the TV and select the AV mode. ● Slide the TV/CABLE/SAT/DVD switch to DVD.
Filename [DR-M7EK_06Name.fm] Masterpage:Right 3Column DR-M7EK_01.
Filename [DR-M7EK_06Name.fm] Masterpage:Left0 DR-M7EK_06Name.fm Page 28 Friday, April 2, 2004 3:28 PM 28 SAT CONTROL SET Satellite Receiver Control Setting Satellite receiver The following procedure is required if you receive satellite channels through a satellite receiver. Approximately 20 seconds before the VIDEO Plus+ timer programming (墌 pg. 56) or Manual Timer programming (墌 pg.
Filename [DR-M7EK_06Name.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 29 Friday, April 2, 2004 11:21 AM 29 CABLE/SAT TV TV STANDBY/ON TV AV TV/CBL/SAT DVD VIDEO 0–9 DEF GHI JKL MNO PQRS TUV WXYZ PR TV DVD Setting satellite receiver’s brand and channel After installation, set the satellite receiver’s brand and channel correctly; otherwise, the Satellite Controller cannot work correctly. ● Turn on the unit. ● Turn on the TV and select the AV mode.
Filename [DR-M7EK_06Name.fm] Masterpage:Left DR-M7EK_01.book Page 30 Friday, April 2, 2004 11:21 AM 30 T-V LINK F Check the result of the test. If the satellite receiver’s channel number has been changed to the same one as you set in step E. Press w e to move the arrow to “YES”, then press ENTER to finish the Sat Control Set mode. T-V Link Functions When you connect the unit to your TV via a fully-wired 21-pin SCART cable (墌 pg. 18), the following functions are available.
Filename [DR-M7EK_07Playback.fm] Masterpage:Right0 DR-M7EK_01.book Page 31 Friday, April 2, 2004 11:21 AM 31 PLAYBACK OPERATIONS To play back an MP3/JPEG disc, see “Playback with MP3/JPEG Navigation” (墌 pg. 78). Basic Playback A Load a disc. A Press x to open the disc tray. B Place the disc on the disc tray. ● For details, refer to “Placing a Disc” (墌 pg. 10). ● Turn on the unit. ● Turn on the TV and select the AV mode. ● Slide the TV/CABLE/SAT/DVD switch to DVD.
Filename [DR-M7EK_07Playback.fm] Masterpage:Left+ DR-M7EK_01.book Page 32 Friday, April 2, 2004 11:21 AM 32 PLAYBACK OPERATIONS (cont.) Playback Features ● Turn on the unit. ● Turn on the TV and select the AV mode. ● Slide the TV/CABLE/SAT/DVD switch to DVD. CABLE/SAT TV TV DVD STANDBY/ON TV AV TV/CBL/SAT DVD VIDEO 0–9 DEF GHI JKL MNO PQRS TUV WXYZ TOP MENU TOP MENU NOTE: When “X” appears on the TV screen in step 1, the disc does not have a top menu or disc menu.
Filename [DR-M7EK_07Playback.fm] Masterpage:Right-No-Heading DR-M7EK_07Playback.fm Page 33 Monday, April 5, 2004 9:48 AM 33 High-Speed Search Resume Function During playback, press 5 for forward high-speed search, or 3 for reverse high-speed search. It is possible to memorise the position where you stop playback and resume playback from that position. ● Be sure to set “RESUME” to “ON” or “DISC RESUME”. (墌 pg. 94) ● Each press of the button increases the search speed for each direction.
Filename [DR-M7EK_07Playback.fm] Masterpage:Left+ DR-M7EK_01.book Page 34 Friday, April 2, 2004 11:21 AM 34 PLAYBACK OPERATIONS (cont.) NOTES: ● When a monaural programme or bilingual programme changes to a stereo programme while recording, a mark signal is automatically recorded. ● When a DVD-R/RW (Video mode) disc is finalised, marked points marked before finalising will be deleted, and programmes will be divided automatically into “chapters” approximately every 5 minutes. (墌 pg.
Filename [DR-M7EK_07Playback.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 35 Friday, April 2, 2004 11:21 AM 35 Angle Selection Audio Language/Sound Selection You can enjoy a variety of scene angles if a DVD VIDEO disc contains “multi-angle” parts, where the same scene was shot from different angles. If the disc contains “multi-angle” parts, “ ” appears on the TV screen at the beginning of the “multi-angle” part. Some DVD VIDEO discs contain the multiple audio language or sound.
Filename [DR-M7EK_07Playback.fm] Masterpage:Left+ DR-M7EK_01.book Page 36 Friday, April 2, 2004 11:21 AM 36 PLAYBACK OPERATIONS (cont.) 0–9 NOTE: It is not possible for DVD-R/DVD-RW (Video mode) disc playback to switch the audio channel. The audio channel is played back as set in “AUDIO REC” (墌 pg. 92).
Filename [DR-M7EK_07Playback.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 37 Friday, April 2, 2004 11:21 AM 37 Recording/playback status display Live Memory Playback CABLE/SAT TV TV VIDEO ABC This unit records pictures onto DVD-RAM discs, instead of video tapes, then plays back the pictures recorded on the discs. This makes it possible to achieve high-speed writing and read-out that has not been possible with conventional VCRs, enabling recording and playback simultaneously.
Filename [DR-M7EK_07Playback.fm] Masterpage:Left+ DR-M7EK_01.book Page 38 Friday, April 2, 2004 11:21 AM 38 PLAYBACK OPERATIONS (cont.) Overview of Live Memory Playback You can play back a programme you are recording from the beginning while continuing to record or timer record onto a DVD-RAM disc. This is called “Live Memory Playback”.
Filename [DR-M7EK_07Playback.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 39 Friday, April 2, 2004 11:21 AM 39 Display during Live Memory Playback During recording, you can watch at your will what was previously recorded or is currently being recorded. It is possible to perform freely normal playback operations (forward/reverse high-speed search and variable-speed search) within the range of the orange or blue bar on the TV screen.
Filename [DR-M7EK_07Playback.fm] Masterpage:Left+ DR-M7EK_01.book Page 40 Friday, April 2, 2004 11:21 AM 40 PLAYBACK OPERATIONS (cont.
Filename [DR-M7EK_07Playback.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 41 Friday, April 2, 2004 11:21 AM 41 ● Turn on the unit. ● Turn on the TV and select the AV mode. ● Slide the TV/CABLE/SAT/DVD switch to DVD. CABLE/SAT TV TV CABLE/SAT DVD STANDBY/ON TV AV TV/CBL/SAT DVD TV TV% DEF GHI JKL MNO PQRS TUV WXYZ CANCEL TOP MENU TIMER ENTER 2 8 RETURN PREVIOUS NEXT SLOW PLAY/SELECT SLOW REC STOP/CLEAR PAUSE REC MODE LIVE CHECK Press 4.
Filename [DR-M7EK_07Playback.fm] Masterpage:Left+ DR-M7EK_01.book Page 42 Friday, April 2, 2004 11:21 AM 42 PLAYBACK OPERATIONS (cont.) Using Play Set Up Menu How to Access Play Set Up Menu Press ON SCREEN twice whenever a disc is loaded. Contents of Play Set Up Menu during playback DVD VIDEO Play Set Up Menu allows you to control various playback functions. Some of the functions operated on Navigation Menu can be controlled on Set Up Menu.
Filename [DR-M7EK_07Playback.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 43 Friday, April 2, 2004 11:21 AM 43 Basic operation on Play Set Up Menu CABLE/SAT TV TV DVD STANDBY/ON TV AV TV/CBL/SAT DVD Example: When selecting Picture Control function of DVD VIDEO During playback or while stopped DEF GHI JKL MNO PQRS TUV WXYZ CANCEL 1 Access Play Set Up Menu. TV% ABC Press ON SCREEN twice. ● The item currently selected is highlighted and pointed by H.
Filename [DR-M7EK_07Playback.fm] Masterpage:Left+ DR-M7EK_01.book Page 44 Friday, April 2, 2004 11:21 AM 44 PLAYBACK OPERATIONS (cont.) Repeat Playback CABLE/SAT TV DVD STANDBY/ON TV AV TV/CBL/SAT DVD TV VIDEO ABC 0–9 & You can repeat playback as you like according to the type of disc. TV% DEF GHI JKL MNO PQRS TUV WXYZ 1 Access Play Set Up Menu. PR Press ON SCREEN twice. CANCEL 2 Select the menu item.
Filename [DR-M7EK_07Playback.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 45 Friday, April 2, 2004 11:21 AM 45 A-B Repeat Playback Locating the beginning of a desired selection You can repeat the desired part. During playback You can locate the beginning of a title, chapter, group or track. 1 Access Play Set Up Menu. During playback or while stopped Press ON SCREEN twice. 1 Access Play Set Up Menu. 2 Select the menu item. Press ON SCREEN twice. Press w e to select “ ”.
Filename [DR-M7EK_07Playback.fm] Masterpage:Left+ DR-M7EK_01.book Page 46 Friday, April 2, 2004 11:21 AM 46 PLAYBACK OPERATIONS (cont.) Time Search Simulated Surround Effect You can play back a disc from the desired point by specifying the elapsed playing time from the beginning of a title (DVD-RAM, DVD-R, DVD-RW and DVD VIDEO) or a disc (Video CD/SVCD and Audio CD). It is possible to get a simulated surround effect from your stereo system.
Filename [DR-M7EK_07Playback.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 47 Friday, April 2, 2004 11:21 AM 47 Adjusting the picture quality Setting the progressive mode You can obtain optimal picture quality by selecting an appropriate picture mode. You can obtain optimal picture quality by selecting whether the content on the disc is processed by field (video source) or by frame (film source). 1 Access Play Set Up Menu. Press ON SCREEN twice. 2 Select the menu item.
Filename [DR-M7EK_07Playback.fm] Masterpage:Left+ DR-M7EK_01.book Page 48 Friday, April 2, 2004 11:21 AM 48 PLAYBACK OPERATIONS (cont.) Programme Playback Random Playback You can play back up to 30 tracks in the desired order. You can play back all the tracks on the disc in random order. While stopped While stopped 1 Access Play Set Up Menu. 1 Access Play Set Up Menu. Press ON SCREEN twice. Press ON SCREEN twice. 2 Select the menu item. 2 Select the menu item.
Filename [DR-M7EK_07Playback.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 49 Friday, April 2, 2004 11:21 AM 49 B Access the “PARENTAL LOCK” screen. Parental Lock This function restricts playback of DVD VIDEO discs which contain violent (and other) scenes according to the level set by the user. For example, if a movie which includes violent scenes supports the parental lock feature, such scenes which you do not want to let children view can be cut or replaced by other scenes. ● Turn on the unit.
Filename [DR-M7EK_07Playback.fm] Masterpage:Left+ DR-M7EK_01.book Page 50 Friday, April 2, 2004 11:21 AM 50 PLAYBACK OPERATIONS (cont.) To change the settings To temporarily release Parental Lock You can change the Parental lock settings later. When you set the parental lock level strictly, some discs may not be played back at all.
Filename [DR-M7EK_07Playback.fm] Masterpage:Right-No-Heading DR-M7EK_01.
Filename [DR-M7EK_07Playback.fm] Masterpage:Left+ DR-M7EK_01.book Page 52 Friday, April 2, 2004 11:21 AM 52 LC LI LK LR LS LT LU LV LY MA MC MD MG MH ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ NA NC NE NF NG NI NL NO NP NR NU NZ OM PA PE PF PG PH PK PL PM PN PR PT PW PY QA RE RO RU RW Page 52 PLAYBACK OPERATIONS (cont.
Filename [DR-M7EK_08Recording.fm] Masterpage:Right0 DR-M7EK_01.book Page 53 Friday, April 2, 2004 11:21 AM 53 RECORDING C Set the recording speed. Basic Recording Press REC MODE repeatedly until the desired recording speed appears. ● Each time you press REC MODE, the recording speed changes as follows: XP ] SP ] LP ] EP ] FR60–FR360*, FR420, FR480 ] (Back to the beginning) ● Turn on the unit. ● Turn on the TV and select the AV mode. ● Slide the TV/CABLE/SAT/DVD switch to DVD.
Filename [DR-M7EK_08Recording.fm] Masterpage:Left+ DR-M7EK_01.book Page 54 Friday, April 2, 2004 11:21 AM 54 RECORDING (cont.) Recording Features Instant Timer Recording (ITR) This easy method lets you record for from 30 minutes to 6 hours (selectable in 30-min. increments), and shuts the unit off after recording is finished. 1 Start recording. Press 7 on the unit. VIDEO 7 Press 7 again. On the front display panel, “0:30” appears. REC MODE SAT# 2 Engage the ITR mode.
Filename [DR-M7EK_08Recording.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 55 Friday, April 2, 2004 11:21 AM 55 Free Rate Function NOTES: To record the entire programme, the unit automatically set the appropriate recording speed depending on the combination of the total time of the programme to be recorded and either the remaining disc space or the specified recording time (from 60 minutes to 480 minutes).
Filename [DR-M7EK_08Recording.fm] Masterpage:Left0 DR-M7EK_01.book Page 56 Friday, April 2, 2004 11:21 AM 56 TIMER RECORDING A Load a disc. VIDEO Plus+ Timer Programming ® A Press x to open the disc tray. B Place a recordable disc on the disc tray. ● For details, refer to “Placing a Disc” (墌 pg. 10). C Press x to close the disc tray. B Access the VIDEO Plus+ screen. Press VIDEO Plus+. You can programme this unit to timer-record as many as 8 programmes.
Filename [DR-M7EK_08Recording.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 57 Friday, April 2, 2004 11:21 AM 57 the following recording options as E Set required. A Press w e to select the desired option. B Press rt to select the desired setting, then press ENTER. “REC MODE” (墌 pg. 54, “Recording Speed”) (墌 pg. 55, “Free Rate Function”), “VPS/PDC” (墌 pg. 59, “PDC Recording”)*, “DAILY/WEEKLY” (in the right column, “Daily/Weekly Rec Function” ), “NAME” (墌 pg.
Filename [DR-M7EK_08Recording.fm] Masterpage:Left+ DR-M7EK_01.book Page 58 Friday, April 2, 2004 11:21 AM 58 TIMER RECORDING (cont.) A Load a disc. Manual Timer Programming A Press x to open the disc tray. B Place a recordable disc on the disc tray. ● For details, refer to “Placing a Disc” (墌 pg. 10). C Press x to close the disc tray. You can programme this unit to timer-record as many as 8 programmes.
Filename [DR-M7EK_08Recording.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 59 Friday, April 2, 2004 11:21 AM 59 F Enter the recording stop time. Press w e to select “STOP”, then press rt repeatedly to set the desired stop time. ● Each press of rt advances/goes back the stop time in 1-min. increments. ● To advance/go back the stop time in 30-min. increments, press and hold rt. G Enter the channel position. Press w e to select “TV PROG”, then press rt repeatedly to select the desired channel.
Filename [DR-M7EK_08Recording.fm] Masterpage:Left+ DR-M7EK_01.book Page 60 Friday, April 2, 2004 11:21 AM 60 TIMER RECORDING (cont.) To make the disc for On-Disc Timer Programming On-Disc Timer Programming A Load a disc. A Press x to open the disc tray. B Place a recordable disc on the disc tray. On-Disc Timer Programming is a function used with discs that are especially intended for a specific programme. The disc is then programmed for a programme you always watch every day or every week.
Filename [DR-M7EK_08Recording.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 61 Friday, April 2, 2004 11:21 AM 61 F Enter the recording stop time. Press w e to select “STOP”, then press rt repeatedly to set the desired stop time. ● Each press of rt advances/goes back the stop time in 1-min. increments. ● To advance/go back the stop time in 30-min. increments, press and hold rt. G Enter the channel position. Press w e to select “TV PROG”, then press rt repeatedly to select the desired channel.
Filename [DR-M7EK_08Recording.fm] Masterpage:Left+ DR-M7EK_01.book Page 62 Friday, April 2, 2004 11:21 AM 62 TIMER RECORDING (cont.) How discs are overwritten (Example 1) To record a 1-hour serial drama every Friday in SP mode Overwritten 1st Blank 2nd 1st 2nd 3rd The first programme is overwritten by the third. Overwritten 4th 3rd The second programme is overwritten by the forth.
Filename [DR-M7EK_08Recording.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 63 Friday, April 2, 2004 11:21 AM 63 C Access the programme screen. CABLE/SAT TV TV DVD STANDBY/ON TV AV TV/CBL/SAT DVD VIDEO & PROG/CHECK TV% ABC DEF GHI JKL MNO PQRS TUV WXYZ CANCEL SHOW VIEW/ PROG/CHECK SAT# VIDEO Plus+ SAT# TIMER NAVIGATION ENTER RETURN MENU PREVIOUS rtwe ENTER NEXT SLOW PLAY/SELECT SLOW REC STOP/CLEAR PAUSE Press rt to select the programme, then press ENTER.
Filename [DR-M7EK_08Recording.fm] Masterpage:Left+ DR-M7EK_01.book Page 64 Friday, April 2, 2004 11:21 AM 64 TIMER RECORDING (cont.) When programmes overlap each other CABLE/SAT TV TV DVD If “PROGRAM OVERLAPPED” appears, you have another programme overlapping the programme you have just made. Confirm with the arrow on “OK”, then press PROG/CHECK. Programme Check screen appears and conflicting programmes will be highlighted in pink.
Filename [DR-M7EK_08Recording.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 65 Friday, April 2, 2004 11:21 AM 65 Automatic Satellite Programme Recording This function allows you to automatically record a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the unit’s L-2 IN/DECODER connector and programme the timer on the satellite receiver.
Filename [DR-M7EK_09Navigation.fm] DR-M7EK_01.book Page 66 Friday, April 2, 2004 11:21 AM 66 Masterpage:Left0 NAVIGATION Library Database DVD Navi The Library Database DVD Navi enables you to search and select the desired programmes recorded on a DVD-RAM/R/RW disc very easily. You can record up to 99 programmes on a disc. Each time a programme is recorded on the disc, the information of the programme is registered for the Library Database DVD Navi automatically.
Filename [DR-M7EK_09Navigation.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 67 Friday, April 2, 2004 11:21 AM 67 Using Library Database DVD Navi system, you can easily modify registered information, edit the programme or play list, as well as search for the beginning of each programme. About registration of information The following information is automatically registered for each programme when ordinary recording or timer recording is performed, then stored in an area specified on the unit.
Filename [DR-M7EK_09Navigation.fm] Masterpage:Left+ DR-M7EK_01.book Page 68 Friday, April 2, 2004 11:21 AM 68 NAVIGATION (cont.) Scan for Beginning(s) of Programme(s) ● Turn on the TV and select the AV mode. ● Slide the TV/CABLE/SAT/DVD switch to DVD. You can scan the beginning of the programme easily with the Library Database DVD Navi. A Turn on the unit. Press DVD 1.
Filename [DR-M7EK_09Navigation.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 69 Friday, April 2, 2004 11:21 AM 69 Modify Index Modify Original Information A Turn on the unit. Press DVD 1. B Access the Index screen. ● Turn on the TV and select the AV mode. ● Slide the TV/CABLE/SAT/DVD switch to DVD.
Filename [DR-M7EK_09Navigation.fm] Masterpage:Left+ DR-M7EK_01.book Page 70 Friday, April 2, 2004 11:21 AM 70 NAVIGATION (cont.) Modify Programme Name Perform steps A to C of “Modify Index” (墌 pg. 69) before continuing. Modify Category Perform steps A to C of “Modify Index” (墌 pg. 69) before continuing. A Access the modify screen. A Access the modify screen. B Enter new name. B Select new category. A Press rt w e to move the arrow to “MODIFY”, then press ENTER.
Filename [DR-M7EK_09Navigation.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 71 Friday, April 2, 2004 11:21 AM 71 Delete programme You cannot record any more with Library Database DVD Navi once the registered programmes on the disc reach 99 programmes. Deleting unnecessary programmes after dubbing (墌 pg. 81, “Edit To Or From Another Recorder”) or other operations can increase remaining time and available recording capacity.
Filename [DR-M7EK_09Navigation.fm] Masterpage:Left+ DR-M7EK_01.book Page 72 Friday, April 2, 2004 11:21 AM 72 NAVIGATION (cont.) Modify Play List Information ● Turn on the TV and select the AV mode. ● Slide the TV/CABLE/SAT/DVD switch to DVD. Create Play List A Turn on the unit. Press DVD 1. B Load a disc. A Press x to open the disc tray. B Place a DVD-RAM or DVD-RW (VR mode) disc that was recorded with this unit on the disc tray. ● For details, refer to “Placing a Disc” (墌 pg. 10).
Filename [DR-M7EK_09Navigation.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 73 Friday, April 2, 2004 11:21 AM 73 H Return to the normal screen. Press NAVIGATION. NOTES: ● There may be a discrepancy of several seconds between the scene you intend to edit, and the scene which is actually edited. ● The title, index and category of the play list can be modified in the same way as “ORIGINAL”. (墌 pg.
Filename [DR-M7EK_09Navigation.fm] Masterpage:Left+ DR-M7EK_01.book Page 74 Friday, April 2, 2004 11:21 AM 74 D Set edit-in and edit-out points. A Find the point where you want the moved scene to begin, then press ENTER with the arrow on “IN”. The edit-in time is fixed and the elapsed playing time starts counting again. B Find the point where you want the moved scene to end, then press ENTER with the arrow on “OUT”. The edit-out time is fixed. C Press 4 to start playback.
Filename [DR-M7EK_09Navigation.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 75 Friday, April 2, 2004 11:21 AM 75 Play back play list Perform steps A to C of “Create Play List” (墌 pg. 72) before continuing. A Select the play list(s). Press w e to move the arrow on the index (small still pictures) of the desired play list. ● When you want the plural play lists to be played back continuously, press MEMO after selecting the desired play lists. The numbers of the playback order appear on the index.
Filename [DR-M7EK_09Navigation.fm] Masterpage:Left+ DR-M7EK_01.book Page 76 Friday, April 2, 2004 11:21 AM 76 NAVIGATION (cont.) Modify Library Information Scan for Programme from library Programme information can be registered in the unit’s memory for up to 1,300 programmes. It is helpful when finding out on which disc the desired programme is recorded. A Press NAVIGATION. The Library Database DVD Navi screen appears. B Press rt w e to move the arrow to “LIBRARY”, then press ENTER.
Filename [DR-M7EK_09Navigation.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 77 Friday, April 2, 2004 11:21 AM 77 Register disc Delete information A Turn on the unit. A Turn on the unit. B Load a disc. B Access the library screen. Press DVD 1. A Press x to open the disc tray. B Place a disc you want to register on the disc tray. Press DVD 1. ● For details, refer to “Placing a Disc” (墌 pg. 10). C Press x to close the disc tray. A Press NAVIGATION.
Filename [DR-M7EK_09Navigation.fm] DR-M7EK_01.book Page 78 Friday, April 2, 2004 11:21 AM 78 Masterpage:Left+ NAVIGATION (cont.) Playback with MP3/JPEG Navigation This unit can play back discs that MP3 sound files and JPEG image files taken with digital still cameras or other devices are recorded. The MP3/JPEG Navigation enables you to search and select the desired files recorded on CD-R/RW or CD-ROM discs very easily.
Filename [DR-M7EK_09Navigation.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 79 Friday, April 2, 2004 11:21 AM 79 Locating the desired group and tracks A Load a disc. A Press x to open the disc tray. B Place a disc on the disc tray. ● For details, refer to “Placing a Disc” (墌 pg. 10). C Press x to close the disc tray. B Access the MP3/JPEG Navigation screen. Press NAVIGATION. The MP3/JPEG Navigation screen appears. C Display the item. For MP3 Playback Press w e to move the arrow to “MP3”.
Filename [DR-M7EK_10Editing.fm] Masterpage:Left0 DR-M7EK_01.book Page 80 Friday, April 2, 2004 11:21 AM 80 EDITING You can use a camcorder as the source player and your unit as the recording deck. Edit From A Camcorder Slide the TV/CABLE/SAT/DVD switch to DVD. A Make connections.
Filename [DR-M7EK_10Editing.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 81 Friday, April 2, 2004 11:21 AM 81 Edit To Or From Another Recorder You can use your unit as the source player or as the recording deck. Slide the TV/CABLE/SAT/DVD switch to DVD. A Make connections. Connect the player’s 21-pin SCART connector to the unit’s 21-pin SCART connector as illustrated.
Filename [DR-M7EK_10Editing.fm] Masterpage:Left+ DR-M7EK_01.book Page 82 Friday, April 2, 2004 11:21 AM 82 EDITING (cont.) Output/Input Set ● Turn on the TV and select the AV mode. ● Slide the TV/CABLE/SAT/DVD switch to DVD. CABLE/SAT TV TV CABLE/SAT DVD STANDBY/ON TV AV TV/CBL/SAT DVD TV DVD A Press rt to move the arrow to “L-1 OUTPUT” or “L-1 INPUT”, then press ENTER. B Press rt to select the appropriate setting, then press ENTER.
Filename [DR-M7EK_10Editing.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 83 Friday, April 2, 2004 11:21 AM 83 L-2 Select Setting (L-2 SELECT) Set “L-2 SELECT” to the appropriate mode depending on the type of appliance connected to the unit’s L-2 IN/DECODER connector. Perform steps A and B of “L-1 Output and L-1 Input Setting (L-1 OUTPUT and L-1 INPUT)” on page 82. the input mode for the L-2 IN/ A Select DECODER connector. A Press rt to move the arrow to “L-2 SELECT”, then press ENTER.
Filename [DR-M7EK_10Editing.fm] Masterpage:Left+ DR-M7EK_01.book Page 84 Friday, April 2, 2004 11:21 AM 84 EDITING (cont.) You can dub selected audio from a DVD or Audio CD disc to a digital audio device. However, it is not possible to dub copy-protected discs. Digital Audio Dubbing Example: Dubbing to an MD A Make connections. ● Turn on the TV and select the AV mode. ● Slide the TV/CABLE/SAT/DVD switch to DVD.
Filename [DR-M7EK_10Editing.fm] Masterpage:Right0 DR-M7EK_01.book Page 85 Friday, April 2, 2004 11:21 AM 85 REMOTE CONTROL On the remote control Remote Control Functions Keep pressing SET UP down during steps A – B. A Change the remote control code. Press the number key “1” for 1, “2” for 2, “3” for 3 or “4” for 4. Remote 1/2/3/4 Code Switching The remote control is capable of controlling four JVC video units independently. Each of the units can respond to one of four codes (1, 2, 3 or 4).
Filename [DR-M7EK_10Editing.fm] Masterpage:Left+ DR-M7EK_01.book Page 86 Friday, April 2, 2004 11:21 AM 86 REMOTE CONTROL (cont.) TV Multi-Brand Remote Control Your remote control can operate the basic functions of your TV set. In addition to JVC TVs, other manufacturer’s TVs can also be controlled. Before performing the following steps: ● Turn off the TV using its remote control. ● Slide the TV/CABLE/SAT/DVD switch to TV.
Filename [DR-M7EK_10Editing.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 87 Friday, April 2, 2004 11:21 AM 87 Satellite Receiver Multi-Brand Remote Control Your remote control can operate the basic functions of your satellite receiver set. In addition to JVC satellite receivers, other manufacturer’s satellite receivers can also be controlled. Slide the TV/CABLE/SAT/DVD switch to CABLE/SAT.
Filename [DR-M7EK_10Editing.fm] Masterpage:Left0 DR-M7EK_01.book Page 88 Friday, April 2, 2004 11:21 AM 88 SYSTEM CONNECTIONS Connecting To A Satellite Receiver Connect the satellite receiver to the L-2 IN/DECODER connector, then connect the L-1 IN/OUT connector to the TV’s connector. NOTES: ● ● ● ● Set “L-2 SELECT” to “VIDEO” or “S-VIDEO”. (墌 pg. 83) You can use the Automatic Satellite Programme Recording function (墌 pg. 65) with this connection.
Filename [DR-M7EK_10Editing.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 89 Friday, April 2, 2004 11:21 AM 89 Connecting To A Dolby Digital Decoder Or An Amplifier With Built-in DTS These instructions enable you to connect your unit to a Dolby Digital decoder or an amplifier with built-in DTS. DIGITAL OUT (COAXIAL) Dolby Digital decoder or amplifier with built-in DTS To DIGITAL AUDIO input Back of unit Coaxial cable (not provided) Optical cable (not provided) Make connections.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Left0 DR-M7EK_01.book Page 90 Friday, April 2, 2004 11:21 AM 90 SUBSIDIARY SETTINGS Various modes of this unit are categorized into menus nested in 2 levels shown in the following table. To change the settings of these modes, find the desired mode in the menu (for details on each menu, see pages 91 through 94), then follow the procedure below. Mode Set ● Turn on the unit. ● Turn on the TV and select the AV mode. ● Slide the TV/CABLE/SAT/DVD switch to DVD.
Filename [DR-M7EK_11Subsidiary.fm] DR-M7EK_01.book Page 91 Friday, April 2, 2004 11:21 AM Masterpage:Right-No-Heading 91 AUDIO OUTPUT (The boldface settings in the table below indicate the settings at your purchase.) 8 DIGITAL AUDIO OUT DOLBY DIGITAL/PCM STREAM/PCM PCM ONLY 8 ANALOG AUDIO OUT STEREO DOLBY SURROUND 8 D. RANGE CONTROL NORMAL WIDE RANGE TV MODE Set to the appropriate mode according to the type of the device connected to DIGITAL OUT connector.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Left+ DR-M7EK_01.book Page 92 Friday, April 2, 2004 11:21 AM 92 SUBSIDIARY SETTINGS (cont.) RECORDING SET (The boldface settings in the table below indicate the settings at your purchase.) 8 SAVE AS LIBRARY OFF ON 8 XP MODE REC AUDIO DOLBY DIGITAL LINEAR PCM 8 AUDIO REC NICAM 1/MAIN NICAM 2/SUB MONO When this function is set to “ON”, the recording information is automatically stored in the library.
Filename [DR-M7EK_11Subsidiary.fm] DR-M7EK_01.book Page 93 Friday, April 2, 2004 11:21 AM Masterpage:Right-No-Heading 93 DISPLAY SET (The boldface settings in the table below indicate the settings at your purchase.) 8 SUPERIMPOSE OFF AUTO You can select the modes of indications superimposed on the TV screen. OFF: To turn off superimposed indications. AUTO: To superimpose operational indications for approximately five seconds just after the corresponding operation.
Filename [DR-M7EK_11Subsidiary.fm] DR-M7EK_01.book Page 94 Friday, April 2, 2004 11:21 AM 94 Masterpage:Left+ SUBSIDIARY SETTINGS (cont.) OTHERS (The boldface settings in the table below indicate the settings at your purchase.) 8 AUTO TIMER OFF ON When this function is set to “ON”, the timer is automatically engaged when the unit power is turned off, and automatically disengaged when the unit is powered back on.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 95 Friday, April 2, 2004 11:21 AM 95 VIDEO Plus+ System Setup ® IMPORTANT: Normally, Auto Set Up (墌 pg. 21), Preset Download (墌 pg. 23) or Auto Channel Set (墌 pg. 96) sets the Guide Program numbers automatically. You need to set the Guide Program numbers manually only in the following cases.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Left+ DR-M7EK_01.book Page 96 Friday, April 2, 2004 11:21 AM 96 SUBSIDIARY SETTINGS (cont.) Your unit needs to memorise all necessary stations in channel positions in order to record TV programmes. Auto Channel Set automatically assigns all receivable stations in your area to call them up by using the PR +/– buttons without going through any vacant channels. Tuner Set ● Turn on the unit. ● Turn on the TV and select the AV mode.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 97 Friday, April 2, 2004 11:21 AM 97 IMPORTANT: ● In certain reception conditions, station names may not be stored correctly, and Auto Guide Program Number Set may not work properly. When the Guide Programme numbers are not set properly, the programme that you do not intended to record will be timer-recorded by the VIDEO Plus+ system of the unit.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Left+ DR-M7EK_01.book Page 98 Friday, April 2, 2004 11:21 AM 98 SUBSIDIARY SETTINGS (cont.) D Select the band. Delete A Channel A Press rt to select “BAND”, then press ENTER. B Press rt to change the band between CH (regular) and CC (cable), then press ENTER. Perform steps A and B of “Manual Channel Set” on page 97 to access the Confirmation screen before continuing. A Select the item. Press rt w e to select the item you want to delete.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 99 Friday, April 2, 2004 11:21 AM 99 Set Stations (A) Set Stations (B) Set station names that are registered in your unit. Set station names other than the ones registered in your unit. Perform steps A and B of “Manual Channel Set” on page 97 to access the Confirmation screen before continuing. A Select the item. Press rt w e to select the item you want. B Access the Manual Channel Set screen. Press ENTER twice.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Left+ DR-M7EK_01.book Page 100 Friday, April 2, 2004 11:21 AM 100 SUBSIDIARY SETTINGS (cont.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Right 3Column DR-M7EK_01.book Page 101 Friday, April 2, 2004 11:21 AM 101 TV Station Channel Number Guide Only the main stations are listed. There are in addition many relay stations, and full lists are available from the BBC and ITV. BBC1 BBC2 ITV London & South-East Bluebell Hill.........................40 46 43 Crystal Palace .......................26 33 23 Dover...................................50 56 66 Heathfield ............................
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Left+ DR-M7EK_01.book Page 102 Friday, April 2, 2004 11:21 AM 102 SUBSIDIARY SETTINGS (cont.) Clock Set IMPORTANT: ● Turn on the unit. ● Turn on the TV and select the AV mode. ● Slide the TV/CABLE/SAT/DVD switch to DVD. CABLE/SAT TV TV CABLE/SAT DVD STANDBY/ON TV AV TV/CBL/SAT DVD TV DVD VIDEO DEF GHI JKL MNO PQRS TUV WXYZ B Access the “CLOCK SET” screen. PR A Press w e to select “INITIAL SET UP”, then press ENTER.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 103 Friday, April 2, 2004 11:21 AM 103 D Set Just Clock. The default setting is “OFF”. A Press rt to select “JUST CLOCK”, then press ENTER. B Press rt to set to the desired mode, then press ENTER. ● For the Just clock function, refer to “Just Clock” on page 102. ● If you set to “OFF”, you can disregard the next step as you won’t be able to receive regular clock adjustments.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Left+ DR-M7EK_01.book Page 104 Friday, April 2, 2004 11:21 AM 104 SUBSIDIARY SETTINGS (cont.) Format a DVD-RAM disc Format A Disc A Access the Main Menu screen. Press SET UP. Some DVD-RAM/RW discs are unformatted. Format the disc when you use an unformatted disc or you want to delete all recordings and data on the disc. ATTENTION: ● When a disc is formatted, all recordings and data are erased. It is impossible to restore them.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Right-No-Heading DR-M7EK_01.book Page 105 Friday, April 2, 2004 11:21 AM 105 Finalise A Disc Finalising DVD-R/RW discs recorded on this unit makes it possible for the discs to be played back on other DVD players. DVD-RW discs are finalised in the mode that the discs were formatted, enabling playback on compatible DVD players. Titles input in the Library Database DVD Navi are registered as titles in the DVD menu. (墌 pg. 32, 70) ● Turn on the unit.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Left+ DR-M7EK_11Subsidiary.fm Page 106 Monday, April 5, 2004 9:51 AM 106 SUBSIDIARY SETTINGS (cont.) Scan Mode Set Tray Lock You can select the scan mode from two modes: Interlaced scan mode which is used in the conventional TV system, and Progressive scan mode which enables reproduction of higher-quality images. For details, refer to “GLOSSARY” (墌 pg. 111). You can lock the disc tray to prohibit the unwanted disc ejection by children.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Right0 DR-M7EK_01.book Page 107 Friday, April 2, 2004 11:21 AM 107 TROUBLESHOOTING Before requesting service for a problem, use this chart and see if you can solve the trouble yourself. Small problems are often easily solved, and this can save you the trouble of sending your unit off for repair. GENERAL SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. No power is supplied to the unit. ● The AC power plug is disconnected from the mains.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Left+ DR-M7EK_01.book Page 108 Friday, April 2, 2004 11:21 AM 108 TROUBLESHOOTING (cont.) RECORDING SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. The desired programme cannot be recorded. ● The channel position does not correspond to that in the receiving area. Set the correct channel position for the receiving broadcast. (墌 pg. 96) 2. Recording and editing cannot be made. ● No disc or a disc not being compatible with the unit is loaded.
Filename [DR-M7EK_11Subsidiary.fm] DR-M7EK_01.book Page 109 Friday, April 2, 2004 11:21 AM Masterpage:Right-No-Heading 109 ON-SCREEN MESSAGES MESSAGE DESCRIPTION MEMORY IS FULL NOTHING MORE CAN BE REGISTERED IN THE LIBRARY IF YOU DELETE UNNECESSARY TITLE INFORMATION, YOU CAN THEN REGISTER ADDITIONAL INFORMATION The memory is full for registration for the Navigation system. The recording cannot be started even though the capacity for the recording is enough. (墌 pg.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Left+ DR-M7EK_01.book Page 110 Friday, April 2, 2004 11:21 AM 110 TROUBLESHOOTING (cont.) ON-SCREEN MESSAGES (cont.) MESSAGE DESCRIPTION PRESS [STOP] AGAIN TO STOP RECORDING During Live Memory playback, 8 has been pressed. (墌 pg. 40) TIMER RECORDING COMPLETED Timer recording has finished during Live Memory playback.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Right0 DR-M7EK_01.book Page 111 Friday, April 2, 2004 11:21 AM 111 GLOSSARY 8 Aspect ratio 8 Multiangle The ratio of vertical and horizontal sizes of a displayed image. The horizontal vs. vertical ratio of conventional TVs is 4:3, and that of wide-screens is 16:9. By recording multiple scenes progressing at the same time in a single title, the user can select view angles. This feature is called the multiangle function.
Filename [DR-M7EK_11Subsidiary.fm] Masterpage:Left0 DR-M7EK_01.book Page 112 Friday, April 2, 2004 11:21 AM 112 SPECIFICATIONS GENERAL Power requirement : AC 220 V – 240 Vd, 50 Hz/60 Hz Power consumption Power on : 33 W Power off : 17.6 W Temperature Operating : 5°C to 40°C Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (WxHxD) : 435 mm x 70 mm x 346 mm Weight : 4.5 kg VIDEO/AUDIO Recordable disc Recording format DVD-RAM DVD-R DVD-RW : DVD-RAM 12 cm (4.7 GB/9.
Filename [DR-M7EK_01IX.fm] Masterpage:Right0 DR-M7EK_01.book Page 113 Friday, April 2, 2004 11:21 AM 113 LIST OF TERMS A P A-B Repeat Playback ............................................ 45 Adjusting the picture quality .................................. 47 Angle Selection .................................................... 35 Audio Channel Selection ....................................... 36 Audio Language/Sound Selection ........................... 35 AUDIO OUTPUT ..................................
Filename [DR-M7EK_01IX.fm] DR-M7EK_01.
Filename [DR-M7EK_01IX.fm] DR-M7EK_01.
Filename [DR-M7EK_13Cov4.fm] DR-M7EK_01.