Manual

Using the SEA Modes
The SEA (Sound Effect Ampfifier) modes give you control of the way your music sounds.
IMPORTANT:
When using the remote control, check to see if its
remote control mode selector is set to the correct
position:
To operate this receiver, set it to "AUDIOITVI
VCR" (except when selecting the DBS tuner as
the source).
[_11" ,t?!1"1'7;_I',I,--]:f'-11_'_# I_
You can adjust and store your own SEA adjustment into memory
(SEA USERMODE).
Belbre you start, remember...
• There is a time limit in doing the following steps, if the setting is
canceled before you finish, start from step 1 again.
g'tmra H
On the front panel:
SEA MODE
Press SEA MODE repeatedly until the SEA fill
mode you want appears on the display.
• Each time you press the button, the SEA mode
changes as follows:
SEA ROCK--SEA MUSICAL--_SEA MOVIE--]
SEA COUNTRY
SEA OFF *- SEA USERMODE _- SEA JAZZ _-J
SEA ROCK: Gives a heavy sound. Both high and low
frequencies are boosted.
SEA MUSICAL: Enhances the mid-frequency range, which
the human voice is mostly made up of.
SEA MOVIE: Adds breadth to sounds so you feel like
you are in a movie theater.
SEA COUNTRY: Enhances the high-frequency range so that
instruments such the violin and banjo are
emphasized.
SEA JAZZ: Gives a feeling of a live atmosphere.
Good for acoustic music.
SEA USERMODE: Your odginal SEA adjustment (see the
right).
SEA OFF: No SEA mode is applied (see below).
On the front panel ONLY'.
If you do not want to store your adjustment, but rather want to adjust
the SEA temporarily, skip step 4 below.
1. Press SEAADJUST repeatedly SEAADJUST
untilthe frequency range (100Hz, II ^ .ll
lkHz or 10kHz) you want appears
on the display,
%..I...11 I II I i i i.... i
'..JI...."II"II.._'.=%' "...=I
Ei_F_
>_ _ -_
.--.I,...i i I h.lh.ll..l..T
'-'k..rl .L%' r....I I.:1.
---i
2. Turn MULTI JOG to adjust the
SEA level of the selected frequency
range.
• I_rning it clockwise increases the level.
N
• Turning it counterclockwise decreases the level.
This FR means this adjustment can be
applied to the front speakers only
Notes:
• TheSEAmodescannotbeusedforrecording.
• When the SEA mode is turned on, the SEA indicator lights up on
the display
• When the SEA mode is used with the DAP mode (see page 23),
sounds may be distorted. If this happens, turn off the DAP mode or
decrease the effect level of the DAP mode.
To cancel the SEA mode
Press SEA MODE repeatedly t ntil "SEA OFF' appears. The SEA
indicator goes off from the display.
From the remote control:
1. Press SOUND.
The 10 keys are activated for sound adjustments.
2, Press SEA MODE repeatedly until
the SEA mode you want appears
on the display.
SOUND
SEA MODE
To cancel the SEA mode
Press SEA MODE repeatedly until "SEA OFF" appears in step 2
above. The SEA indicator goes off fi-om the display.
10k--
3. Repeat step 1 and 2 to adjust other frequency
ranges if necessary;
SEA MEMORY
4. Press TUNER/SEA MEMORY.
Your adjustment is stored into the SEA
USERMODE.
To recall your own SEA adjustment
Press SEA MODErepeatedly until "SEA USERMODE" appears.
To erase a stored adjustment
Storing a new adjustment into SEA USERMODE erases the
previously stored one.
19