Manual

l Basic Settings
Some of the following settings are required after connecting and positioning your speakers in your listening room, while
others will make operations easie_
You can record any source playing through the receiver to a cassette
deck (or an MD recorder) connected to the TAPE/MD jacks and the
VCR connected to the VCR jacks at the same time.
While recording, you can listen to the selected sound source at
whatever sound level you like, without affecting the sound levels of
the recording.
Note:
The output volume level, tone adjustment (see page 10), bass boost
(see page 10) and DSP modes (see page !8) cannot affect the
recording.
When you have connected the MD recorder to the TAPE/MD jacks
or the DBS tuner to the TV SOUND/DBS jacks on the rear panel,
change the source name shown on the display when you select the
MD recorder or the DBS tuner as the source.
On the front panel ONLY:
When changing the source name from "TAPE" to "MD':
1. Press TAPE/MD. '......
• Make sure "TAPE" appears on the display.
%/"
2, Press and hold SOURCE NAME
(TAPE/MD) until "ASSGN. MD"
appears on the display-.
If the sounds you hear from the front right and left speakers are
unequal, you can adiust the speaker output balance.
Betbre you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start fi-om step 1 again.
On the front Banel ONLY:
1. Press ADJUST repeatedly until ADJUST
"L/R BALANCE" appears on the _====x-x'_W'x)
display.
%_/
• Once you have pressed ADJUS'I; MULTI CURSOR A / V can
be also used for selecting "L/R BALANCE."
'lb change the source name from "MD" to "TAPE," repeat
the same procedure above (in step 1, make sure "MD" appears
on the display).
When changing the source name from "TV SOUND" to "DBS':
1. Press TV SOUND/DBS.
• Make sure "TV SOUND" appears on the
display.
2. Press and hold SOURCE NAME
(TV SOUND/DBS) until "ASSGN.
DBS" appears on the display.
2. Press MULTI CURSOR <s / E> to ..........
adjust the balance. [I-_ I_ I_-]]
• Pressing <1decreases the right channel I "+1
output (from "L-2I to "1{-21 ) _:'-,ff._.N_-._
• Pressing t> decreases the left channel .';....-" _,...//
output (from "R-2 l" to "L-2 l').
k'_RN_I R,'_ b-am,'Ig/r/rll_11II;'I_
Register whether or not you have connected a subwoofeE
Betore you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start fi-om step 1 again.
'lb change the source name from "DBS" to "TV SOUND,"
repeat the same procedure above (in step 1, make sure "DBS"
appears on the display),
Note:
Without changing the source name, you can still use the connected
components. However, there may be some inconvenience.
- "TAPE" or "TV SOUND" will appear on the display when you select
the MD recorder or DBS tuner.
- You cannot select the digital input (see page 14) for the MD
recorder and the DBS tune_
- You cannot use the COMPU LINK remote control system (see page
26) to operate the MD recorder.
On the front Banel ONLY:
1. Press SETTING repeatedly until SETTING
"SUBWOOFER" appears on the _=====_'N>
display.
%/"
• Once you have pressed SETTING, MULTI CURSOR A / V
can be also used for selecting "SUBWOOFER."
• The display changes to show the current setting.
multi cu_om
PressMULTICURSORto IIjI
YES: Select this when a subwoofer is used.
NO: Select this when no subwoofer is used.
11