Manual

_1_ obtain the best possible sun-ound sound of the DSP (Digital
Signal Processor) modes (see page 18), you have to register the
information about the speakers arrangement after all connections are
completed.
Befbre you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start fi-om step 1 again.
Front, Center, and Rear Speaker Setting
Register the sizes of all the connected speakers,
On the front panel ONLY:
1, Press SETTING repeatedly until
"FRONT SPK" (Front Speaker),
"CENTER SPK" (Center
Speaker), or "REAR SPK" (Rear
Speaker) appears on the display.
• Once youhave pressed SETTING, MULTI
CURSOR A / V can be also used for
selecting the speakers.
SETTING
MULtiCW_
2. Press MULTI CURSOR <1/ E> to /[_I " " il
A
select the appropriate item about I<_ I_l c>
the speaker selected in the above _.'}."_";_x_
step. _,./ _,/
r LARGE'.._,. SMALL'.._. NONE q
LARGE: Select this when the speaker size is relatively large.
SMALL: Select this when the speaker size is relatively small
NONE: Select this when you have not connected a speakeE
(Not selectable for the fi-ont speakers)
3. Repeat steps 1 and 2 to select the appropriate
items lbr the other speakers.
Notes:
• Keep the following comment in mind as reference when adjusting.
- If the size of the cone speaker unit built in your speaker is greater
than 12 cm, select "LARGE," and if it is smaller than 12 cm,
select "SMALL."
• If you have selected "NO" for the subwoofer setting, you can only
select "LARGE" for the front speaker setting.
• Ifyouhaveselected"SMALL"forthefrontspeakersetting, you
cannnot select "LARGE" for the center and rear speaker settings.
• When you change your speakers, you need to register the
information about the speaker again.
Center Delay Time Setting
Register the delay time of the sound from the center speaker,
comparing that of the sound fi-om the front speakers.
If the distance fi-om your listening point to the center speaker is
equal to that to the front speakers, select 0 msec. As the distance to
the center speaker becomes shorter, increase the delay time.
• 1 msec increase (or decrease) in delay time corresponds to 30 cm
decrease (or increase) in distance.
• When shipped fi-om the tZactory, delay time is set to 0 msec.
On the front panel ONLY:
SETTING
1. Press SETTING repeatedly until _/.x
"CENTER DELAY" appears on
the display.
• Once you have pressed SETTING, MULTI CURSOR A / V
can be also used for selecting "CENTER DELAY."
• The display changes to show the current setting.
. Press MULTI CURSOR <_ / E> to _ ...........
select the delay time of the center/L IIAII
speaker output. II L;YqLk
• Pressing t> increases the delay time from _-,_ ..'._x_" 2
0 msec ("C. DELAY: 0ms ) to 5 msec ("C. ": "_"
DELAY: 5ms').
• Pressing <1 decreases the delay time from
5 msec ("C. DELAY: 5ms') to 0 msec ("C.
DELAY: 0ms').
Rear Delay Time Setting
Register the delay time of the sound fronl the rear speakers,
comparing that of the sound fi-om the front speakers.
If the distance fi-om your listening point to the rear speakers is equal
to that to the front speakers, select 0 msec. As the distance to the rear
speakers becomes shorter, increase the delay time.
• 1 msec increase (or decrease) in delay time corresponds to 30 cm
decrease (or increase) in distance.
• Rear delay time for Dolby Digital and DTS Digital Surround is to
be set to 5 msec.
• When shipped fi-om the tZJctory, delay time is set to 5 msec.
On the front oanel ONLY:
1. Press SETTING repeatedly until
SETTING
"REAR DELAY" appears on the
display.
• Once you have pressed SETTING, MULTI CURSOR A / V
can be also used for selecting "REAR DELAY."
• The display changes to show the current setting.
.
Press MULTI CURSOR <_ / E> to r-_ ..........
selectt edelaytimeaft erear11<1 14
speaker output. [_...-.',_",_ [x%_
• Pressing t> increases the delay time from _'_.../._ _..
0 msec ("R. DELAY: 0ms') to 15 msec
("R. DELAY: 15ms').
• Pressing <1 decreases the delay time from
15 msec ("R. DELAY: 15ms") to 0 msec
("R. DELAY: 0ms').
12