Manual

Creating Rea i÷ticSound Fie ds
3 Press SOUND.
lO keys are activated for sound ac[justments.
4 Press TEST to check if you can hear the "rEST
sounds through all the speakers at the
equal level.
"TEST TONE L" starts flashing on the
display, and a test tone comes out of the
speakers in the following order:
.__ TESTTONEL .__TESTTONEC.__ TESTTONER
(Leftfronl speaker) (Center speaker) (Right front speaker) |
/
TESTTONE LS ÷ TESTTONE RS_
(Left rear speaker) (Right rear speaker)
Notes:
• Youcanadjustthespeakeroutputlevelswithoutoutputtingthe
test tone.
• No test tone comes out of the center speaker when "CNTR SP"
is set to "NONE,"
• No test tone comes out of the rear speakers when "REAR SP"
is set to "NONE,"
,5 Adjust the speaker output levels
(-10 to +10).
At[just the center speakers and rear speakers levels
by comparing with the sound from the front
speakers.
• To at[just the center speaker level, press
CENTER +_.
• To ac[just the left rear speaker level, press
REAR.L +_.
• To ac[just the right rear speaker level, press
REAR•R +_.
6 Press TEST again to stop the test TE_
tone.
Onthe front panel:
You can also use the buttons on the fi'ont panel to at/just the
Surround modes. However, no test tone is available when using the
buttons on the front panel. So, make ac[justments while listening to
the sound of the source played back.
[ Set the analog or digital input mode for the
source you like to listen and start playing.
When playing back software encoded with Dolby Digital and
DTS Digital Surround, select the digital input mode (see page
]_).
Adjust the speaker output levels.
I) Press ADJUST repeatedly until one
of the following indications (with the
current setting)* appears on the
display.
REAR L : To Mjust the left rear speaker output level
( 10 to +10).
o!o)
2)
-- CENTER+ _,_
_> When
-- REAR. L4-
@ @ following adjustment.
4 Turn on Panorama control on or off.
- _'_+ I) Press ADJUST repeatedly until
"PANORAMA" (with the current
setting)* appears on the display.
* "OFF" is the initial setting. If you have
* "0" is the initial setting. If you have already changed the
setting, another number (level) will be shown.
Press CONTROL UP A/ _##"%
DOWN • to adjust the selected
speaker output levels. "x_
Repeat steps I) and 2) to adjust the other
speaker levels.
you select "PL H MUSIC," you can go to the
A0a0ST
already changed the setting, "ON" will be shown.
2) Press CONTROL UP A/DOWN • .......oow,,i uv
to select if you turn on or off
Panorama control. _>
• Each time you press the button, "ON" anti
"OFF" change alternately.
OFF
: Select this when you like to enjoy originally
recorded sounds.
2 Press SURROUND ON/OFF _o..oo.oo_
repeatedly to activate Surround
mode.
Each time you press the button, Surround mode turns on anti off
alternately.
• If you are playing back software encoded with Dolby Digital
multichannel, "DOLBY DIGITAL" is selected.
• If you are playing back software encoded with DTS Digital
Surround, "DTS SURROUND" is selected.
• If you are playing back any software other SIJ[_ROIJNDMODE
than above, you can select "PL II MUSIC"
or "PL II MOVIE" according to the source
by pressing SURROUND MODE.
([I] PRO LOGIC II indicator lights up on the display.)
Tocancel Surround mode
Press SURROUND ON/OFF again so that "SURROUND OFF"
appears on the display.
• If Surround mode is canceled while playing back multichannel
digital software, all channel signals are mixed and output through
the front speakers (and subwoofer if you have connected a
subwoofer and set the subwoofer setting correctly--"YES').
If'you like to adjust sound, go to step 3.
22