User Manual

18
Menu Configuration (cont.)
Set-Up Menu
Function Setting
Settings for the sub menu display, color of the tally lamp, and the intensity of the button lamps.
Item To do Setting value
sub menu Position Select the contents and displaying position of “sub menu.”
The setting values and features are as follows.
Lower1, Upper1, Lower2,
Upper2
Lower1 : Displays the current setting and adjustment bar at the lower part of the screen.
Upper1 : Displays the current setting and adjustment bar at the upper part of the screen.
Lower2 : Displays the current setting at the lower part of the screen.
Upper2 : Displays the current setting at the upper part of the screen.
• The adjustment bar is not displayed for some items.
Sync Term Specify the terminal resistant value of the RGB input synchronized signal from the COMPO./RGB
terminal.
• Normally, select “High”. Select “Low” when the display becomes unstable due to the length
of a connection cable.
Low, High
Tally Setting
Set the color and mode of the tally lamp using external control.
Tally Type
Normal
Half
:
:
Light up the entire tally.
Light up the left and right halves of the tally individually.
Normal, Half
Tally Color
Set the tally color when “Tally Type” is set to “Normal”. Green, Red
Dimmer Select the intensity of the button lamps. Normal, Dark
Illumination Select whether illumination is activated/deactivated. Off, On
Component Phase Deactivates the function of PHASE adjustment (Picture adjustment knob and “Picture Sub
Adjust” in Set-Up Menu) (☞ on page 19) except when an NTSC signal comes in.
Enable, Disable
Remote Active On
Standby
Set the conditions for the power switch by external control (serial). Off, On
On
Off
:
:
Can power on by external control after powered OFF.
Cannot power on by external control after powered OFF.
LCD Saver
Configure the setting for reducing damage to the LCD panel for long-time use. (☞ on page 21)
Setting 1st Start Set the standby time. 00h-24h
Work
Time
Set the time for performing the function.
01h-06h
Contrast Set the contrast reduction. Save, Normal
Backlight Reduce the backlight brightness. Save, Normal
OSD
Contrast
Set the contrast reduction of the OSD display.
Save, Normal
Side Mask Select whether to use the side panel.
* The Side Mask function works no matter whether the LCD Saver is active or stopped.
Off, On
reset Restore the default settings for all the items in “LCD Saver”.
Execute Execute the LCD Saver function.
Cancel Stop the LCD Saver function. (“Cancel” will be grayed out during the function stop.)
Status Display the LCD Saver status. Off, Ready
Start After Stop the LCD Saver function. **h **min
Function Key Setting Specify the function assigned to the F1/F2 button.
Function1
Specify the function assigned to the F1 button.
See pages 13 to 20 for details of the
functions assigned to Function 1 and
Function 2.
- - -, Aperture, I/P Mode,
Frame, Center Marker,
Level Meter Display,
Gamma,
Color Temperature,
CRC Error, Manual Aspect
Function2
Specify the function assigned to the F2 button.
Function Display Select whether to display the status of the assigned function when you press the F1/F2 button. Off, Mode-1, Mode-2
Off
Mode-1
Mode-2
:
:
:
No status display. Perform the registration function.
Display the status. Perform the registration function.
Display the status. Do not perform the registration function.
Perform the registration function when the status is displayed and the button is
pressed again.
● You can also display “Function Key Setting” Menu by pressing the button when the menu is not displayed.
● Each time you press the F1/F2 button, the setting value for the assigned function changes in order.
Ex: When “Color Temperature” is assigned
Each time you press the button, three setting values alternate.
DT-E15L4_EN.indb 18DT-E15L4_EN.indb 18 10/31/2012 9:55:09 PM10/31/2012 9:55:09 PM