M150SEK_00.
Filename [M150SEK_02Safety.fm] Masterpage:Left0 M150SEK_00.book Page 2 Wednesday, June 15, 2005 4:04 PM 2 EN SAFETY FIRST Safety Precautions The rating plate and the safety caution are on the rear of the unit. DISCLAIMER OF LIABILITY JVC shall not be liable for any loss relating to the unit’s failure to properly record, store or playback any content (video, audio or otherwise) for any reason whatsoever.
Filename [M150SEK_02Safety.fm] Masterpage:Right+ M150SEK_00.book Page 3 Wednesday, June 15, 2005 4:04 PM SAFETY FIRST The STANDBY/ON A button does not completely shut off mains power from the unit, but switches operating current on and off. ABB shows electrical power standby and ACB shows ON. Failure to heed the following precautions may result in damage to the unit, remote control or disc. 1. DO NOT place the unit ^ ^ in an environment prone to extreme temperatures or humidity. ^ in direct sunlight.
Filename [M150SEK_02Safety.fm] M150SEK_00.book Page 4 Wednesday, June 15, 2005 4:04 PM 4 EN Masterpage:Left+ SAFETY FIRST Some Do’s And Don’ts On The Safe Use Of Equipment This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. DO read the operating instructions before you attempt to use the equipment.
Filename [M150SEK_03TOC.fm] Masterpage:Right0 M150SEK_00.book Page 5 Wednesday, June 15, 2005 4:04 PM CONTENTS SAFETY FIRST 2 Safety Precautions .........................................................................2 Some Do’s And Don’ts On The Safe Use Of Equipment ...............4 Information On Reception Of Digital Transmissions ......................4 DISC INFORMATION 6 About Discs ....................................................................................
Filename [M150SEK_04DiscInfo.fm] M150SEK_00.book Page 6 Wednesday, June 15, 2005 4:04 PM 6 EN Masterpage:Left0 DISC INFORMATION About Discs Recordable/Playable Discs You can use discs with the following logos for recording and playback. DVD-RAM DVD-RW 12 cm: 4.7 GB/9.4 GB 8 cm: 1.4 GB/2.8 GB Ver. 2.0/2x speed Ver. 2.1/1x - 3x speed Ver. 2.2/5x speed 12 cm: 4.7 GB 8 cm: 1.4 GB Ver. 1.1/1x - 2x speed (Video mode/VR mode) Ver. 1.2/4x speed (Video mode/VR mode) DVD-R 12 cm: 4.7 GB 8 cm: 1.4 GB Ver. 2.
Filename [M150SEK_04DiscInfo.fm] M150SEK_00.book Page 7 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ DISC INFORMATION EN 7 Discs For Playback Only Unplayable Discs You can use discs with the following logos for playback only. The unit may not be able to play back or it may take some time to read a disc depending on the recording status or condition of the disc, or if the disc is scratched, dirty or warped.
Filename [M150SEK_04DiscInfo.fm] M150SEK_00.book Page 8 Wednesday, June 15, 2005 4:04 PM Masterpage:Left+ 8 EN DISC INFORMATION Recording Medium And Format DVD-RAM ● Recording and erasing can be performed as many times as possible on a disc. ● Editing can be performed after recording, such as deleting unwanted parts. ● While recording, it is possible not only to start playback of a programme currently being recorded, but also to watch another programme previously recorded.
Filename [M150SEK_04DiscInfo.fm] M150SEK_00.book Page 9 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ DISC INFORMATION DVD VIDEO Marks Placing A Disc Sometimes marks are printed on a DVD disc and/or on its packaging to indicate information regarding the contents and functions of the disc. Check the marks indicating the contents and functions of the disc. Note, however, that in some cases a disc may not include a mark even for a function it supports.
Filename [M150SEK_04DiscInfo.fm] M150SEK_00.book Page 10 Wednesday, June 15, 2005 4:04 PM 10 EN DISC INFORMATION Care And Handling Of Discs How to handle discs When handling a disc, do not touch the surface of the disc. Since discs are made of plastic, they are easily damaged. If a disc gets dirty, dusty, scratched or warped, the images and sound will not be picked up correctly, and such a disc may cause the unit to malfunction.
Filename [M150SEK_05Name.fm] M150SEK_00.book Page 11 Wednesday, June 15, 2005 4:04 PM Masterpage:Right0 INDEX EN 11 Front View A B C D E F G PR+ RAM/RW STANDBY/ON DV F-1 S-VIDEO H A B C D E F G VIDEO I L(MONO) AUDIO DV IN R J K L H Front Display Panel A pg. 12 I S-video Input Connector [S-VIDEO] A pg. 55 J Video/Audio Input Connectors [VIDEO/AUDIO (L(MONO)/ R)] A pg. 55 K DV Input connector [DV IN (A*)] A pg.
Filename [M150SEK_05Name.fm] M150SEK_00.book Page 12 Wednesday, June 15, 2005 4:04 PM Masterpage:Left+ 12 EN INDEX Front Display Panel AB C D E F H G I LPCM FR XP SP LP EP VR -RW VCD DVD -RAM K L J DISC M A Video Indicator (z) A pg. 22 Lights when video mode is selected by pressing TV/VIDEO z. B Disc Type Indicator When a disc is loaded, the type of the disc is indicated. Disc Status Indicator When a disc is running, the disc marks rotate.
Filename [M150SEK_05Name.fm] M150SEK_00.book Page 13 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ INDEX Remote Control A B C T Q R S T U V U W V W X D E F G H I J K L M N O P Q R S Y Z a b c d e f g h i j k l m n o A TV/VIDEO Button For switching the input of a JVC TV. B Open/Close Button (M) C Number Keys A pg. 23, 32, 33 D Cancel Button (CANCEL) A pg. 33 E Auxiliary Button (AUX) A pg. 38 F GUIDE Button A pg. 37 G Programme Button (PROG) A pg. 38 H Top Menu Button (TOP MENU) A pg.
Filename [M150SEK_05Name.fm] M150SEK_00.book Page 14 Wednesday, June 15, 2005 4:04 PM Masterpage:Left+ 14 EN INDEX Check Contents CHECK ALL THE CONTENTS SHOWN BELOW DVD Video Recorder PR S TA N D B Y / O N RAM/RW PUSHÐOPEN PR Ð RF Cable AAAB Batteries (x 2) 21-pin SCART Cable Infrared Remote Control Unit I You are now ready to install your unit. (A pg.
Filename [M150SEK_05Name.fm] M150SEK_00.book Page 15 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ INDEX On-Screen Display When using Live Memory playback A When ON SCREEN on the remote control is pressed, various operational indicators appear on the TV screen. To clear the operational indicators, press ON SCREEN twice.
Filename [M150SEK_05Name.fm] M150SEK_00.book Page 16 Wednesday, June 15, 2005 4:04 PM 16 EN Masterpage:Left0 INSTALLING YOUR NEW UNIT Basic Connection THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED.
Filename [M150SEK_05Name.fm] M150SEK_00.book Page 17 Wednesday, June 15, 2005 4:04 PM Masterpage:Right0 INITIAL SETTINGS Auto Set Up Auto Channel Set/Auto Clock Set After the A button on the unit (or DVD A on the remote control) is pressed for the first time to turn on the unit, the Auto Set Up function sets the tuner channels and clock automatically.
Filename [M150SEK_05Name.fm] M150SEK_00.book Page 18 Wednesday, June 15, 2005 4:04 PM 18 EN INITIAL SETTINGS Results Of Auto Set Up Appearing On The Front Display Panel If both Auto Channel Set and Auto Clock Set have been performed successfully, the correct current time is displayed. Turn on the TV and select an input mode such as EXT1, then make sure that all necessary stations have been stored in the unit’s memory by using the PR +/– button(s).
Filename [M150SEK_05Name.fm] M150SEK_00.book Page 19 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ INITIAL SETTINGS Language EN 19 Monitor Set ● Turn on the unit. ● Turn on the TV and select an input mode such as EXT1. ● Slide the TV/DVD switch to DVD. You can select the monitor type depending on the TV used when you play back DVD VIDEO discs recorded for wide-screen TVs. 1 2 DVD TV 3 Press SET UP to access the Main Menu screen.
Filename [M150SEK_05Name.fm] M150SEK_00.book Page 20 Wednesday, June 15, 2005 4:04 PM 20 EN Masterpage:Left+ INITIAL SETTINGS 4 Setting DTV You can set the language and channel selection method when watching TV programmes and performing recording with this unit. ● Turn on the unit. ● Turn on the TV and select an input mode such as EXT1. ● Slide the TV/DVD switch to DVD. DVD TV Press selection keys to select AFAVOURITE MODEB, then press ENTER. NOTE: If AFavouritesB under AEDIT CHANNEL LISTB (A pg.
Filename [M150SEK_06DVD Operation.fm] M150SEK_06DVD Operation.fm Page 21 Thursday, June 16, 2005 5:59 PM Masterpage:Right0 BASIC OPERATIONS ON DVD DECK EN 21 Displaying The Subtitles Basic Operation (TV) ATTENTION: ● It is not possible to watch pay-TV with this unit. ● While watching Digital terrestrial broadcast (DVB-T), ON SCREEN and DISPLAY buttons function as colour buttons. To operate these buttons as ON SCREEN and DISPLAY buttons, press INFO to display the information bar.
Filename [M150SEK_06DVD Operation.fm] M150SEK_00.book Page 22 Wednesday, June 15, 2005 4:04 PM 22 EN Masterpage:Left+ BASIC OPERATIONS ON DVD DECK To play back an MP3/JPEG disc, see APlayback With MP3/JPEG NavigationB (A pg. 52). Basic Playback 1 Load a disc. ● For details, refer to APlacing A DiscB (A pg. 9). ● Pressing M also closes the disc tray. ● Playback begins automatically if an auto-playback DVD disc is ● Turn on the unit. ● Turn on the TV and select an input mode such as EXT1.
Filename [M150SEK_06DVD Operation.fm] M150SEK_00.book Page 23 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ BASIC OPERATIONS ON DVD DECK 23 Locating The Start Point Of The Item Or Skip The Item Playback Features ● Turn on the unit. ● Turn on the TV and select an input mode such as EXT1. ● Slide the TV/DVD switch to DVD. EN Press S or T during playback. ● Pressing T locates the start point of the title (or track) or skips to the marked point in the forward direction, then resumes playback.
Filename [M150SEK_06DVD Operation.fm] M150SEK_00.book Page 24 Wednesday, June 15, 2005 4:04 PM 24 EN Masterpage:Left+ BASIC OPERATIONS ON DVD DECK Resume Function M DVD A MARK TOP MENU DISPLAY Selection Keys (FGDE) ENTER I T N/SLOW + W v w REMAIN ANGLE MENU S O/SLOW o SUBTITLE It is possible to memorise the position where you stop playback and resume playback from that position.
Filename [M150SEK_06DVD Operation.fm] M150SEK_00.book Page 25 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ BASIC OPERATIONS ON DVD DECK EN 25 Marking Positions To Play Back Again Later Angle Selection It is possible to mark positions (up to 999 points) where you want to play back once again later, and start playback from a marked position. You can enjoy a variety of scene angles if a DVD VIDEO disc contains Amulti-angleB parts, where the same scene was shot from different angles.
Filename [M150SEK_06DVD Operation.fm] M150SEK_00.book Page 26 Wednesday, June 15, 2005 4:04 PM 26 EN Masterpage:Left+ BASIC OPERATIONS ON DVD DECK Audio Language/Sound Selection 0-9 Some DVD VIDEO discs contain the multiple audio language or sound. You can select the desired audio language or sound. For some Video CD/SVCD discs, you can switch the audio channel to choose Karaoke either with or without the vocal. 1 Selection Keys (FGDE) ENTER RETURN T MENU S I o AUDIO Press AUDIO during playback.
Filename [M150SEK_06DVD Operation.fm] M150SEK_00.book Page 27 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ BASIC OPERATIONS ON DVD DECK EN 27 Live Memory Playback You can watch a recorded portion of a programme even before recording ends (Live Memory Playback), or watch other programmes (Simultaneous Recording and Playback) while continuing to record onto the DVD-RAM disc.
Filename [M150SEK_06DVD Operation.fm] M150SEK_00.book Page 28 Wednesday, June 15, 2005 4:04 PM 28 EN Masterpage:Left+ BASIC OPERATIONS ON DVD DECK ● Turn on the unit. ● Turn on the TV and select an input mode such as EXT1. ● Slide the TV/DVD switch to DVD. Live Memory Playback You can play back the previous part of the channel you are recording. To watch from the recording start point DVD TV 1 Press I during recording.
Filename [M150SEK_06DVD Operation.fm] M150SEK_00.book Page 29 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ BASIC OPERATIONS ON DVD DECK Buttons To Be Used During Live Memory Playback A NAVIGATION BD CE DS ET FO GN Ho Kw IW Jv L LIVE CHECK A NAVIGATION Displays Library Database Navigation menu. You can choose a title to play back. B D Pressing during pause mode reverses the still picture frame by frame. C E Pressing during pause mode advances the still picture frame by frame.
Filename [M150SEK_06DVD Operation.fm] M150SEK_06DVD Operation.fm Page 30 Wednesday, June 15, 2005 8:09 PM 30 EN Masterpage:Left+ BASIC OPERATIONS ON DVD DECK Using The On-screen Bar The on-screen bar allows you to control various playback functions. Some of the functions operated on Navigation Menu can be controlled on the On-screen bar. Be sure to clear Library Database Navigation screen by pressing NAVIGATION.
Filename [M150SEK_06DVD Operation.fm] M150SEK_00.book Page 31 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ BASIC OPERATIONS ON DVD DECK DVD-RAM/RW/R OFF: Repeat playback is not performed. ALL REPEAT: The whole disc is played back repeatedly. TITLE REPEAT: The current title is played back repeatedly. DVD VIDEO OFF: Repeat playback is not performed. TITLE REPEAT: The current title is played back repeatedly.
Filename [M150SEK_06DVD Operation.fm] M150SEK_00.book Page 32 Wednesday, June 15, 2005 4:04 PM 32 EN Masterpage:Left+ BASIC OPERATIONS ON DVD DECK Adjusting The Picture Quality You can obtain optimal picture quality by selecting an appropriate picture mode. 0-9 1 2 CANCEL ENTER Press selection keys to select A B, then press ENTER. The pop-up window appears under the selected item. DVD-VIDEO Selection Keys (FGDE) I S Press ON SCREEN twice to access the on-screen bar.
Filename [M150SEK_06DVD Operation.fm] M150SEK_00.book Page 33 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ BASIC OPERATIONS ON DVD DECK VIDEO: Suitable for playing back a video source disc. The outlines on the played back pictures will be soft. To clear the on-screen bar Press ON SCREEN. Programme Playback 1 2 3 You can play back all the tracks on the disc in random order. While stopped 1 2 Press ON SCREEN twice to access the on-screen bar.
Filename [M150SEK_06DVD Operation.fm] M150SEK_00.book Page 34 Wednesday, June 15, 2005 4:04 PM 34 EN Masterpage:Left+ BASIC OPERATIONS ON DVD DECK NOTES: Basic Recording ● It is recommended to format a DVD-RAM disc before use if you use the disc on this unit for the first time. (A pg. 67) ● When using a brand-new DVD-RW disc, format the disc either in VR mode or in Video mode. (A pg. 67) ● Recordings made on DVD-R/RW disc must be finalised to play ● Turn on the unit.
Filename [M150SEK_06DVD Operation.fm] M150SEK_00.book Page 35 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ BASIC OPERATIONS ON DVD DECK EN 35 Instant Timer Recording (ITR) Recording Features It is possible to set the recording time during recording. Upon completing recording, the unit stops and shut off automatically. R 1 2 Press R on the unit to start recording. 3 If you want to record for more than 30 minutes, press R to extend the time. Each press extends recording time by 30 minutes.
Filename [M150SEK_06DVD Operation.fm] M150SEK_00.book Page 36 Wednesday, June 15, 2005 4:04 PM 36 EN BASIC OPERATIONS ON DVD DECK Free Rate Function To record the entire programme, the unit automatically sets the appropriate recording mode depending on the combination of the total time of the programme to be recorded and either the remaining disc space or the specified recording time (from 60 minutes to 480 minutes when using 4.7 GB blank media disc).
Filename [M150SEK_07Timer Recording.fm] M150SEK_00.book Page 37 Wednesday, June 15, 2005 4:04 PM Masterpage:Right0 TIMER RECORDING EN 37 ● You can scroll the programme description field vertically by EPG Timer Programming pressing the yellow (w) or blue (v) button on the remote control. 4 EPG (Electronic Programme Guide) is a system built into this unit to enable viewing of TV programme information. The programme information is part of the text broadcast provided by the individual TV stations.
Filename [M150SEK_07Timer Recording.fm] M150SEK_00.book Page 38 Wednesday, June 15, 2005 4:04 PM 38 EN Masterpage:Left+ TIMER RECORDING 6 Press selection keys to set the desired stop time (ASTOPB), then press E. ● Each press of F G increases/decreases the stop time in 1 minute interval. ● To increase/decrease the stop time in 30 minutes interval, press and hold F G. Manual Timer Programming You can programme this unit to timer record as many as 8 programmes up to 30 days in advance.
Filename [M150SEK_07Timer Recording.fm] M150SEK_00.book Page 39 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ TIMER RECORDING On-Disc Timer Programming On-Disc Timer Programming is a function used with discs that are especially intended for a specific programme. The disc is then programmed for a programme you always watch every day or every week. Since older programmes are automatically overwritten, a single disc can be used without worrying about how much recording capacity remains.
Filename [M150SEK_07Timer Recording.fm] M150SEK_00.book Page 40 Wednesday, June 15, 2005 4:04 PM 40 EN TIMER RECORDING To Timer Record The Programme With The Programmed Disc 1 2 Load a programmed disc. Press DVD A to turn off the power. appears on the front display panel, and the unit enters into timer standby mode. ● To disengage the timer mode, press DVD A again.
Filename [M150SEK_07Timer Recording.fm] M150SEK_00.book Page 41 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ TIMER RECORDING Check, Cancel And Change Programmes TV DVD DVD A GUIDE PROG TIMER j SAT j Selection Keys (FGDE) ENTER CLEAR (o) 1 Disengage the timer mode. lights up on the front display panel, press DVD A. ● When j lights up on the front display panel, press TIMERj, and press DVD A after j lights off. ● When ASAT jB lights up on the front display panel, press SATj.
Filename [M150SEK_07Timer Recording.fm] M150SEK_00.book Page 42 Wednesday, June 15, 2005 4:04 PM 42 EN Masterpage:Left+ TIMER RECORDING Automatic Satellite Programme Recording This function allows you to automatically record a satellite programme which is timer programmed on your external satellite receiver. Connect a satellite receiver to the unit’s [L-2 IN] connector and programme the timer on the satellite receiver. The unit starts or stops recording by the signals input from the satellite receiver.
Filename [M150SEK_08Navigation.fm] M150SEK_00.book Page 43 Wednesday, June 15, 2005 4:04 PM Masterpage:Right0 NAVIGATION The Library Database Navigation enables you to search and select the desired titles recorded very easily. You can record up to 99 titles on a disc. Each time a title is recorded, the information of the title is registered for the Library Database Navigation automatically. So, you can confirm the information of the titles recorded with the Library Database Navigation screen.
Filename [M150SEK_08Navigation.fm] M150SEK_00.book Page 44 Wednesday, June 15, 2005 4:04 PM 44 EN Masterpage:Left+ NAVIGATION Basic Operation Of Original Information You can scan the beginning of the title easily and play back with the Library Database Navigation. ● Turn on the TV and select an input mode such as EXT1. ● Load a DVD disc to play back. ● Slide the TV/DVD switch to DVD.
Filename [M150SEK_08Navigation.fm] M150SEK_00.book Page 45 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ NAVIGATION Delete Unwanted Part Of The Title (DVD-RAM & DVD-RW (VR mode) only) You can delete unwanted part of a title. 1 2 3 4 5 Press NAVIGATION to display the Library Database Navigation screen. Press selection keys to select AORIGINALB, then press ENTER. Press selection keys to select a title whose unwanted part you want to delete, then press G.
Filename [M150SEK_08Navigation.fm] M150SEK_00.book Page 46 Wednesday, June 15, 2005 4:04 PM 46 EN Masterpage:Left+ NAVIGATION Modify Title Name Edit Original Information ● Turn on the TV and select an input mode such as EXT1. ● Load a DVD disc to modify. ● Slide the TV/DVD switch to DVD. ATTENTION: ● It is not possible to modify discs recorded on DVD units from other manufacturers. ● You cannot perform timer recording during editing of index by pressing NAVIGATION.
Filename [M150SEK_08Navigation.fm] M150SEK_00.book Page 47 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ NAVIGATION Basic Operation Of Play List Information 5 Confirm the arrow is on AINB, then press ENTER. ● The edit-in time is displayed on the left of the AINB window. CREATE IN ● Turn on the TV and select an input mode such as EXT1. ● Load a DVD disc to modify. ● Slide the TV/DVD switch to DVD.
Filename [M150SEK_08Navigation.fm] M150SEK_00.book Page 48 Wednesday, June 15, 2005 4:04 PM 48 EN Masterpage:Left+ NAVIGATION Modify Play List Name Edit Play List Information ● Turn on the TV and select an input mode such as EXT1. ● Load a DVD disc to modify. ● Slide the TV/DVD switch to DVD. 1 Perform steps 1 - 4 of AModify IndexB (A pg. 48) before continuing. 2 Press selection keys to select AMODIFY NAMEB, then press ENTER. 3 Input a new title name. See AModify Title NameB (A pg. 46).
Filename [M150SEK_08Navigation.fm] M150SEK_00.book Page 49 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ NAVIGATION Delete Scenes 1 2 3 4 5 Press NAVIGATION to display the Library Database Navigation screen. Press selection keys to select APLAY LISTB, then press ENTER.
Filename [M150SEK_08Navigation.fm] M150SEK_00.book Page 50 Wednesday, June 15, 2005 4:04 PM Masterpage:Left+ 50 EN NAVIGATION Add Scenes 1 Press NAVIGATION to display the Library Database Navigation screen. 2 Press selection keys to select APLAY LISTB, then press ENTER. 3 4 5 Press selection keys to select a play list to which you wish to add a scene, then press G. Press selection keys to select AEDITINGB, then press ENTER. Press selection keys to select AADD SCENEB, then press ENTER.
Filename [M150SEK_08Navigation.fm] M150SEK_00.book Page 51 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ NAVIGATION EN 51 When the disc that contains the selected title is not loaded A prompt screen appears. Load the disc after pressing ENTER to close the prompt screen. Then perform steps 1 - 4. Edit Library Information Each disc recorded on this unit is automatically numbered. If this number is retained, it is possible to find out the titles recorded in a disc quickly.
Filename [M150SEK_08Navigation.fm] M150SEK_00.book Page 52 Wednesday, June 15, 2005 4:04 PM 52 EN NAVIGATION Playback With MP3/JPEG Navigation This unit can play back discs that contain MP3 sound files and JPEG image files taken with digital still cameras or other devices. The MP3/JPEG Navigation enables you to search and select the desired files recorded on CD-R/RW or CD-ROM discs very easily. ● Turn on the TV and select an input mode such as EXT1.
Filename [M150SEK_09Editing.fm] M150SEK_00.book Page 53 Wednesday, June 15, 2005 4:04 PM Masterpage:Right0 EDITING EN 53 The following on-screen display for DV dubbing appears when ON SCREEN is pressed while the channel has been set to ADVB. DV Dubbing DV DUBBING You can dub programmes from a camcorder or DV equipment connected to the unit with a DV cable. The unit’s remote control allows you the limited control of the connected camcorder or DV equipment functions during dubbing.
Filename [M150SEK_09Editing.fm] M150SEK_00.book Page 54 Wednesday, June 15, 2005 4:04 PM 54 EN Masterpage:Left+ EDITING When you dub from DV equipment other than a camcorder A Perform steps 1 - 3. B Locate the point from where you want to start dubbing, then stop on the DV equipment. ● If you pause the DV equipment in this step, a few second’s still picture will be recorded at the beginning of the recorded programme. C Set the input mode to ADV INPUTB on the DV equipment.
Filename [M150SEK_09Editing.fm] M150SEK_00.book Page 55 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ EDITING Edit From A Camcorder You can use a camcorder as the source player and your unit as the recording deck. A If the camcorder has no S-VIDEO output connector: RAM/RW Recorder Press PR +/– to select AF-1B. ● Set AF-1 INPUTB to AVIDEOB for the [VIDEO] input connector, or AS-VIDEOB for the [S-VIDEO] input connector, depending on the connector being used. (A pg.
Filename [M150SEK_09Editing.fm] M150SEK_00.book Page 56 Wednesday, June 15, 2005 4:04 PM 56 EN Masterpage:Left+ EDITING Edit To Or From Another Recorder You can use your unit as the source player or as the recording deck. NOTE: When using another recorder as the recording deck, refer to its instruction manual. A When using your unit as the source player TV receiver Player Your unit 1 Connect another recorder’s 21-pin SCART connector to the unit’s 21-pin SCART connector as illustrated.
Filename [M150SEK_09Editing.fm] M150SEK_00.book Page 57 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ EDITING EN 57 * The boldface settings below indicate the settings at your purchase. Output/Input Set ● Turn on the TV and select an input mode such as EXT1. ● Slide the TV/DVD switch to DVD. 8 L-1 OUTPUT ^ SCART VIDEO / SCART S-VIDEO / SCART RGB / COMPONENT SCART VIDEO: If a connected appliance’s input is compatible only with regular video signals, set to ASCART VIDEOB.
Filename [M150SEK_09Editing.fm] M150SEK_00.book Page 58 Wednesday, June 15, 2005 4:04 PM 58 EN Masterpage:Left+ EDITING NOTES: ● When RGB signals are output from the connected appliance such as a satellite receiver, the unit will record in RGB signals. ● If you have a satellite receiver connected to the [L-2 IN] connector, be sure to set AL-2 SELECTB back to appropriate mode after editing.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.book Page 59 Wednesday, June 15, 2005 4:04 PM Masterpage:Right0 SYSTEM CONNECTIONS Connecting To A Satellite Receiver Outdoor unit Satellite cable 59 Connecting To A Dolby Digital Decoder Or An Amplifier With Built-in DTS Connect the satellite receiver to the [L-2 IN] connector, then connect the [L-1 IN/OUT] connector to the TV’s connector. NOTES: ● Set AL-2 SELECTB to AVIDEO/RGBB or AS-VIDEO/RGBB. (A pg.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.book Page 60 Wednesday, June 15, 2005 4:04 PM 60 EN Masterpage:Left0 SUBSIDIARY SETTINGS * The boldface settings below indicate the settings at your purchase. Mode Set AUDIO OUTPUT ● Turn on the unit. ● Turn on the TV and select an input mode such as EXT1. ● Slide the TV/DVD switch to DVD.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.book Page 61 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ SUBSIDIARY SETTINGS RECORDING SET OTHERS 8 SAVE AS LIBRARY ^ OFF / ON 8 AUTO TIMER ^ OFF / ON When this function is set to AONB, the recording information is automatically stored in the library. For details, refer to AEdit Library InformationB (A pg. 51). 8 XP MODE REC AUDIO ^ DOLBY DIGITAL / LINEAR PCM You can select the audio format when you record a title in XP mode.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.book Page 62 Wednesday, June 15, 2005 4:04 PM 62 EN Masterpage:Left+ SUBSIDIARY SETTINGS Remote Control Functions TV Multi-Brand Remote Control Remote Control 1/2/3/4 Code Switching The remote control is capable of controlling four JVC video units independently. Each of the units can respond to one of the four codes (1, 2, 3 or 4). The remote control is preset to send code 3 signals because your unit is initially set to respond to code 3 signals.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.book Page 63 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ SUBSIDIARY SETTINGS TV Brand Code Table 63 Scan Mode Set BRAND NAME JVC FERGUSON FINLUX FUNAI LG/GOLDSTAR GRUNDIG HITACHI ITT MITSUBISHI MIVAR NEC NOKIA PANASONIC PHILIPS RCA SAMSUNG SANYO SHARP SONY THOMSON TOSHIBA EN CODE If you connect the unit and TV with Component Video Connection (A pg. 11), you can select the scan mode from two modes.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.book Page 64 Wednesday, June 15, 2005 4:04 PM 64 EN Masterpage:Left+ SUBSIDIARY SETTINGS 5 Tuner Set Your unit needs to memorise all necessary stations in channel positions in order to record TV programmes. Auto Channel Set automatically assigns all receivable stations in your area to call them up by using the PR +/– buttons without going through any vacant channels. ● Turn on the unit. ● Turn on the TV and select an input mode such as EXT1.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.book Page 65 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ SUBSIDIARY SETTINGS EN Confirming Images Of Registered Channels Set Stations 1 2 Set station names other than the ones registered in your unit. 3 Press SET UP in DTV mode to access the Main Menu screen. Press selection keys to select AINITIAL SET UPB, then press ENTER. Press selection keys to select AEDIT CHANNEL LISTB, then press ENTER.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.book Page 66 Wednesday, June 15, 2005 4:04 PM 66 EN Masterpage:Left+ SUBSIDIARY SETTINGS 5 Clock Set IMPORTANT: If you performed Auto Set Up (A pg. 17), without ever having set the clock previously, the unit’s built-in clock is also set automatically. Perform the following steps only if ^ ^ Auto Clock Set has not been performed correctly by Auto Set Up. OR ^ you want to change Just Clock setting. (See AJust ClockB in the right column) ● Turn on the unit.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.book Page 67 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ SUBSIDIARY SETTINGS EN 67 Format A DVD-RAM Disc Format A Disc 1 2 Some DVD-RAM/RW discs are unformatted. Format the disc when you use an unformatted disc or you want to delete all recordings and data on the disc. ATTENTION: ● When a disc is formatted, all recordings and data are erased. It is impossible to restore them.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.book Page 68 Wednesday, June 15, 2005 4:04 PM 68 EN Masterpage:Left+ SUBSIDIARY SETTINGS Finalise A DVD-R/RW Disc Finalise A Disc Finalising DVD-R/RW discs recorded on this unit makes it possible for the discs to be played back on other DVD players. DVD-RW discs are finalised in the mode that the discs were formatted, enabling playback on compatible DVD players.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.book Page 69 Wednesday, June 15, 2005 4:04 PM Masterpage:Right0 TROUBLESHOOTING Before requesting service for a problem, use this chart and see if you can solve the trouble yourself. Small problems are often easily solved, and this can save you the trouble of sending your unit off for repair. Initialising Malfunction occurs on the unit. ] Press A to turn off the unit, while holding A, press o for 3 seconds or more.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.book Page 70 Wednesday, June 15, 2005 4:04 PM 70 EN TROUBLESHOOTING Timer Recording Timer programming cannot be made. ● Date and time is not correct. ] Set date and time correctly. (A pg. 18, 66) ● Timer recording is in progress. ] Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes. Timer programming recording does not start. ● Date and time is not correct. ] Set date and time correctly. (A pg.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.book Page 71 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ TROUBLESHOOTING On-screen Message EN 71 DISC NOT REGISTERED IN THE LIBRARY REGISTER DISC? THE i.LINK DEVICE THAT YOU HAVE CONNECTED IS NOT RECOGNIZED MAKE SURE THAT THE DEVICE IS CONNECTED PROPERLY AND POWERED ON ● A disc that is not registered in the library has been inserted. ● An attempt has been made to start DV dubbing when a digital Register the disc as necessary. (A pg.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.
Filename [M150SEK_10Subsidiary.fm] M150SEK_00.book Page 73 Wednesday, June 15, 2005 4:04 PM Masterpage:Right+ APPENDIX EN 73 SPECIFICATIONS GENERAL INPUT/OUTPUT Power requirement AC 220 V - 240 VH, 50 Hz/60 Hz S-video input Y : 1.0 Vp-p, 75 K C : 0.3 Vp-p, 75 K Video input : 1.0 Vp-p, 75 K (pin jack) Audio input : 2 Vrms (pin jack) Audio output : 2 Vrms (pin jack) 21-pin SCART connectors : IN/OUT x 1, IN x 1 i.Link : 4-pin for DV input Component video output Y : 1.0 Vp-p, 75 K PB/PR : 0.
Filename [M150SEK_11IX.fm] Masterpage:Left0 M150SEK_00.book Page 74 Wednesday, June 15, 2005 4:04 PM 74 EN LIST OF TERMS A O A-B Repeat Playback ................................................ 31 Adjusting The Picture Quality ..................................... 32 Angle Selection ........................................................ 25 Audio Channel Selection ........................................... 26 Audio Language/Sound Selection ............................... 26 Auto Channel Set .......
Filename [M150SEK_11IX.fm] M150SEK_00.
M150SEK_00.