LYT2019-001B-M INSTRUCTIONS MANUAL DE INSTRUCCIONES MEMORY CAMERA VIDEOCÁMARA CON MEMORIA GZ-MS130 U EN SP Dear Customer Thank you for purchasing this memory camera. Before use, please read the safety information and precautions contained in pages 2 and 3 to ensure safe use of this product. For Future Reference: Enter the Model No. (located on the bottom of the memory camera) and Serial No. (located on the battery pack mount of the camcorder) below. Model No. Serial No.
Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Easy Start Guide Charge the battery before recording Turn off the camcorder and attach the battery pack. Access lamp Blinks: Accessing files Power/charge lamp Blinks: Charging goes out: Charging finished Do not remove the AC adapter, the battery pack or the SD card when the lamp is blinking. Open the cover Battery Pack The battery pack is not charged at the time of purchase. AC Adapter To AC Outlet (110V to 240V) CAUTION Be sure to use JVC battery packs.
Date/Time Setting S Select [CLOCK SETTING] the LCD monitor to turn on the camcorder Q Open CLOCK ADJUST CLOCK SETTING AREA SETTING SET FOR DAYLIGHT SAVING TIME Power Button SET THE CITY, DATE AND TIME QUIT SET the city closest to the area where you use T Select the camcorder AREA SETTING LCD monitor R NOV.1.2009 04:55PM Select [YES] within 10 seconds QUIT SET Slide your finger up and down on the sensor. Then touch OK. [ON] if daylight U Select saving time is effective.
Video recording CAUTION Before recording an important scene, it is recommended to conduct a trial recording. Q Slide the mode switch to select ! (video) mode R Select recording mode PLAY/REC The mode changes when you press the button. The auto recording indicator appears. [ 4 h 59 m ] 0 : 04 : 01 S M Start recording Press the START/ STOP button to start recording, and press it again to stop.
Playing back Q Select playback mode PLAY/REC The mode changes when you press the button. R Select the desired file Index screen LASER TOUCH OPERATION VIDEO PLAYBACK 1/2 NOV.01.2009 04:55PM DIGEST S Select F(Touch OK) LASER TOUCH OPERATION Playback screen L To perform operations such as forward search or reverse search ( pg. 22) L To view files on TV ( pg. 25) It is recommended to copy your important recorded data to a DVD or other recording media for storage.
Contents GETTING STARTED Index ...................................................... 10 Accessories .......................................... 12 Attaching the core filter ................................ 12 Preparing the Remote Control ..................... 12 Indications on LCD Monitor................. 13 Necessary Settings before Use ........... 15 USING WITH TV Viewing Files on TV .............................. 25 Connection with TV...................................... 25 Playback Operation ........
How to use the Touch Sensor After the menu is displayed on the LCD monitor: Read This First! Make a backup of important recorded data MANUAL SETTING LIGHT REGISTER EVENT VIDEO QUALITY USE DETAIL SETTINGS BASED SET QUIT R Select [SET]. (Touch OK.) Before the actual recording of important data, make a trial recording and play back the recorded data to check that the video and sound have been recorded correctly.
GETTING STARTED Index DC NOTE • The LCD monitor can rotate 270°. • Be careful not to cover 4, 5, 7 and 8 during shooting. EN10 GZ-MS130BU_US_IB_ENB.
Camcorder Touch Sensor OK Button MENU Button Power (1) Button SD Card Slot ( pg. 18) EXPORT Button AV Connector UPLOAD Button ( pg. 36) PLAY/REC Button ( pg. 19, 20, 22, 23) Mode Switch [!, #] DIRECT DVD Button ( pg. 28) INFO Button ( pg. 21) . START/STOP Button ( pg. 19) / SNAPSHOT Button ( pg. 20) 0 Zoom Lever [W 7 , T] ( pg. 21) Speaker Volume Control 1 Speaker 2 DC Connector 3 USB Connector ( pg. 27, 30) 4 5 6 7 8 Camera Sensor LED Light ( pg.
Accessories or AC Adapter AP-V20U/AP-V14U* USB Cable CD-ROM Battery Pack BN-VF808U Audio/Video Cable Core Filter (x2) Lithium Battery CR2025 Pre-installed in the remote control unit. Remote Control RM-V751U NOTE Make sure to use the provided cables for connections. Do not use any other cables. * AP-V14U is not mentioned in the GUIDEBOOK in the supplied CD-ROM. Attaching the Core Filter The core filter reduces interference caused when connecting to other devices. Release the stopper.
Indications on LCD Monitor During both Video and Still Image Recording During Video Recording Only [4h59m] 1/4000 0 W LCD NOV. 1. 2009 T 0 : 0 4 : 0 1 REC PHOTO SD GETTING STARTED LIB. 4:55 PM ! Selected Operation Mode Indicator ( pg. 24) 4 : Auto Mode 3 : Manual Mode # Effect Mode Indicator $ Tele Macro Mode Indicator % LED Light Indicator ( pg. 21) & Scene Select Mode Indicator ( Quick Review Indicator ( pg.19, 20) ) Zoom Indicator ( pg.
Indications on LCD Monitor (Continued) During Video Playback During Still Image Playback 101- 0098 1: 55 : 01 +4 SD SD 8 NOV. 1. 2009 NOV. 1. 2009 4:55 PM ! Mode Indicator # Playlist Playback Indicator (Appears when playing back a playlist.) $ Video Quality: B (ULTRA FINE), C (FINE), D (NORMAL), E (ECONOMY) % Counter & Playback Mode F : Playback Q : Pause K : Forward Search J : Reverse Search G : Forward Slow-Motion E : Reverse Slow-Motion (The number on the left shows speed.
Necessary Settings before Use Charging the Battery Pack L To check the remaining battery power See page 21. L Required charging/recording time 1 Attach the battery pack, then connect the AC adapter. • With the “v” (arrow) on the battery pack pointing at the correct direction, slide the battery pack until it locks in place. DC Jack (approx.) *When the LED light is off and the monitor backlight is set to [STANDARD] mode. Recording time Battery pack Charging time BN-VF808U (Provided) 1 hr. 50 min.
Other Settings SET FOR DAYLIGHT SAVING TIME Date/Time Setting DAYLIGHT SAVING TIME (DST) OFF 1 2 3 Open the LCD monitor to turn on the camcorder. NOV.1.2009 04:55PM SET DAYLIGHT SAVING TIME Set the date and time. Select the item by using the touch sensor and select [}] to set. Select [DISPLAY SETTINGS]. VIDEO WIND CUT AUTO SWITCH REC MEDIA CLOCK SETTING DISPLAY SETTINGS > BASIC SETTINGS > DATE NOV CONFIGURE ON-SCREEN DISPLAY 2009 4 55 QUIT SAVE Select [CLOCK ADJUST].
Language Setting Tripod Mounting The language on the display can be changed. 1 Touch MENU. Bottom of the Camcorder Select [DISPLAY SETTINGS]. GETTING STARTED 2 3 Open the LCD monitor to turn on the camcorder. Align the camcorder stud hole with the tripod stud, and the mounting socket with the screw, and then rotate the camcorder clockwise to mount it to the tripod.
Other Settings (Continued) NOTE • Insert and remove the SD card only while Using an SD Card If you want to record to an SD card, the following operations need to be performed. • Operations are confirmed on the following SD cards: Class 4 or higher compatible SD or SDHC card Panasonic, TOSHIBA, SanDisk, ATP SD card (256 MB to 2 GB) or SDHC card (4 GB to 32 GB). • If other media are used, they may fail to record data correctly, or they may lose data that had already been recorded.
RECORDING/PLAYBACK Recording Files Video Recording Slide the mode switch to select ! (video) mode. Press the PLAY/REC button to select recording mode. PLAY/REC [4 h 59 m] 0:00:00 Press the START/STOP button to start recording. [4 h 59 m] 0:00:01 REC RECORDING/ PLAYBACK SNAPSHOT Approximate remaining time for recording appears. You can also start/stop recording by selecting [REC] on the LCD monitor. (On-screen recording control). L To stop recording Press the START/STOP again.
Recording Files (Continued) Still Image Recording Slide the mode switch to select # (still image) mode. Press the PLAY/REC button to select recording mode. PLAY/REC FINE [9999] Press and hold the SNAPSHOT button halfway. FINE The ? indicator becomes green when the captured image is focused. L To view the last recorded image Select A after shooting. Selecting $ during playback deletes that image. L To change the picture quality Change the settings in [IMAGE QUALITY].
Checking the Remaining Battery Power Zooming Preparation: • Slide the mode switch to select ! or # mode. • Press the PLAY/REC button to select recording mode. Zoom out Zoom in Preparation: • Attach the battery pack. • Press the PLAY/REC button to select recording mode. For ! mode: Press the INFO button three times or INFO and then select ;. For # mode: Press INFO. W: Wide angle You can also zoom out/zoom in by selecting [W] or [T] on the LCD monitor. (On-screen zoom control).
Playing Back Files Video Playback Slide the mode switch to select ! (video) mode. Press PLAY/REC to select the playback mode. VIDEO PLAYBACK 1/2 PLAY/REC NOV.1.2009 04:55PM DIGEST The index screen appears. Select the desired file. L To move to the previous or next page Touch [v] or [V] for over a second. L To play back a few seconds from each select scene of the recorded videos Touch [DIGEST]. L Operations during Video Playback L To delete a video Select * when playback is stopped.
Still Image Playback Slide the mode switch to select # (still image) mode. Press PLAY/REC to select the playback mode. IMAGE PLAYBACK 1/2 PLAY/REC NOV.01.2009 04:55PM Select the desired file. RECORDING/ PLAYBACK The index screen appears. L To move to the previous or next page Touch [v] or [V] for over a second. L To delete a still image Select $. L To change the number of thumbnails (6 thumbnails/20 thumbnails) Move the zoom lever to [T] or [W].
Manual Recording Manual recording mode enables you to set the focus and screen brightness etc. manually. Manual Setting Menu In the manual recording mode: Change to Manual Recording Mode Preparation: • Slide the mode switch to select ! or # mode. • Press the PLAY/REC button to select recording mode. 1 Touch MENU. 2 Select [MANUAL SETTING]. VIDEO MANUAL SETTING LIGHT REGISTER EVENT Select [A/M] twice. VIDEO QUALITY USE DETAIL SETTINGS BASED QUIT SET [4 h 59 m] 3 Select the desired menu.
Viewing Files on TV This camcorder is designed to be used with NTSC-type color television signals. It cannot be used with a television of a different standard. Connection with TV L To connect using the AV connector. Preparation: Turn off all units. AC Adapter Playback Operation After the connection with TV is completed 1 2 3 Set the TV to its VIDEO mode. (Only when connecting the camcorder to the VCR/DVD recorder) Turn on the VCR/DVD recorder, and set the VCR/DVD recorder to its AUX input mode.
EDITING/PRINTING Managing Files CAUTION Do not remove the recording medium or perform any other operation (such as turning off the power) while accessing files. Also, be sure to use the provided AC adapter, as the data on the recording medium may be corrupted if the battery becomes exhausted during operation. If the data on the recording medium becomes corrupted, format the recording medium to use the medium again.
COPYING Copying Files It is recommended to copy your important recorded data to a DVD or other recording media for storage. JVC will not be responsible for any lost data. Types of Copying and Connectable Device Using a DVD Burner Supported discs: 12cm DVD-R, DVD-RW • Regarding DVD-R discs, only unused DVD-R discs can be used. Regarding DVD-RW discs, used DVD-RW discs can also be used, but they need to be formatted before recording.
Copying Files (Continued) Backup All Files Copying Video Files that Have Never Been Copied Preparation: • Connect the camcorder to the DVD burner. • Slide the mode switch to select ! mode. 1 Select [CREATE FROM ALL]. Files that have never been copied to the DVD discs are automatically selected and copied. 1 CREATE DVD CREATE FROM ALL SELECT AND CREATE CREATE DUPLICATE PLAYBACK COPY RECORDED VIDEOS 2 Open the LCD monitor to turn on the camcorder. Press the DIRECT DVD.
Creating a DVD using a PC Please read the “JVC SOFTWARE LICENCE AGREEMENT” in the CD-ROM instruction before you install software. You can copy the data from the camcorder and create a DVD using a PC. Preparation: Load the provided CD-ROM into the PC. In Windows Vista, the auto play dialog box appears. 1 Click [Easy Installation].
Copying Files (Continued) Everio MediaBrowser starts on the PC. R Making Backup on the PC Preparation: • Install the software to the PC. • Make sure that enough free space is left in the PC’s HDD. • Close the LCD monitor to turn off the camcorder. 3 DC Connector AC Adapter Click [All volume in camcorder] and click [Next]. To AC Outlet DC 4 Click [Start]. USB Connector USB Cable Backup starts.
S Making User Lists to Arrange the Files 5 Double-click the recording date. You can make a user list of a certain subject (such as Travel, Athletic meet) and put the files related to the subject into the user list. Preparation: Make backup on the PC. 1 Double-click icon and open the calendar. The files recorded on the day are displayed. 6 2 Drag the file and drop into the user list. Select [Movies only]. To add other files into the user list, repeat steps 5 and 6 4 Click [+].
Copying Files (Continued) T Copying Files to a DVD 4 Preparation: Use a recordable DVD disc (It is recommended to use a DVD-R disc.) 1 Select the user list and click [Create Disc]. 5 2 Input the disc name, select the top menu style and click [Next]. Click [Start]. Click [Select files individually] and click [Next]. To add all the files onto DVD discs, click [Select all files displayed], then go to step 4.
Folder Structure and Extensions Recording medium X = number Contains the still image folders. [DCIM] [XXXJVCSO] Contains the video file folders. [SD_VIDEO] [MGR_INFO] [PRGXXX] [PRGXXX.PGI] [MOVXXX.MOD] [MOVXXX.MOI] Management information* for the media as a whole Management information* Video file Management information* for the video files [PRGXXX] [EXTMOV] [MOV_XXX.MOD] [PRIVATE] Video file which management information is corrupted.
Copying Files (Continued) Dubbing Files to a VCR/DVD Recorder Preparation: • Create a playlist. • Turn off all units. 1 2 L To connect using the AV connectors Set the VCR/DVD recorder to its AUX input mode. Check that the images from the camcorder are input correctly to the VCR/DVD recorder. (analog dubbing) DC Connector Open the LCD monitor to turn on the camcorder. 3 Play back playlists on the camcorder. 1) Touch MENU. 2) Select [DUBBING PLAYBACK]. 3) Select the desired playlist. 4) Select [YES].
Using with a Portable Media Player 3 Turning on the Export Mode You can easily transfer videos recorded in export mode to iTunes®. All the files with the export setting turned on are transferred to PC. For details on transferring, refer to the operation guide of MediaBrowser in the CD-ROM. Select [DONE]. L To cancel the export setting Select the file and press [LIB.] again. L To quit the screen 1) Select [DONE]. 2) Select [YES].
Uploading Files to Websites Turning on the Upload Mode You can upload the file to video sharing websites (You TubeTM) quickly after recording. For more information on YouTube™, visit YouTube™ website: http://www.youtube.com/ Preparation: • Slide the mode switch to select ! mode. • Press the PLAY/REC button to select recording mode Uploading Files For detalis on uploading files, refer to the operation guide of MediaBrowser in the CDROM. 1 2 Connect the camcorder to the PC with the USB cable.
MENU SETTINGS Changing the Menu Settings 1 Touch MENU. 3 2 Select the desired menu. Select the desired setting. VIDEO REGISTER EVENT OFF VIDEO QUALITY ZOOMON ON VIDEO DIS REGISTER EVENT VIDEO QUALITY ZOOM ON IMAGE BLURRED NEED TO SET DIS QUIT ON IMAGE BLURRED NEED TO QUIT SET L To return to the previous screen Select @. L To quit the screen Select [QUIT]. Troubleshooting Before requesting service, consult the following chart.
Troubleshooting (Continued) Trouble Recording Recording cannot be performed. Action • SD Card or Built-In Memory is full. Delete unnecessary files or replace the SD Card. • Insert a commercially available SD card, and set each of the Recording stops by itself. Sound or video are interrupted. [REC MEDIA FOR VIDEO] to [SD CARD] and [REC MEDIA FOR IMAGE] to [SD]. Recording stops automatically after 12 hours of continuous • recording.
Warning Indications Indication SET DATE/TIME! Action • Set the clock. If the message still appears after setting the clock, the battery for the clock has been depleted. Consult your nearest JVC dealer. COMMUNICATING ERROR • Be sure to use JVC battery packs. NOT FORMATTED • Select [OK] and select [YES] to perform formatting. FORMAT ERROR! • Check the operating procedure, and perform once again. • Turn off the camcorder, and turn it on again.
Specifications Camcorder L For general Power supply DC 11 V (Using AC adapter) DC 7.2 V (Using battery pack) Power consumption Approx. 1.8 W* * When the LED light is off and the monitor backlight is set to [STANDARD] mode. Dimensions (W x H x D) 54.5 mm x 65 mm x 112.5 mm (2-1/8”x2-9/16”x4-7/16”) Weight Approx. 245 g (0.54 lbs) (incl. grip belt) Approx. 290 g (0.64 lbs) (incl.
Dimensions (W x H x D) Remote Control 42 mm x 14.5 mm x 91 mm (1-11/16” x 5/8” x 3-5/8”) Power supply Weight DC 3 V Approx. 30 g (0.07 lbs) (incl. battery) Battery life Approx. 1 year (depending on the frequency of use) Design and specifications subject to change without notice. Operating distance Within 5 m (16.
Cautions ATTENTION: The battery you have purchased is recyclable. Please call 1-800-8-BATTERY for information on how to recycle this battery. AC Adapter When using the AC adapter in areas other than the USA The provided AC adapter features automatic voltage selection in the AC range from 110 V to 240 V.
Main Unit • • Fasten the grip belt securely. • When using the camcorder with a tripod, attach the camcorder to the tripod securely. Model Number: GZ-MS130U Trade Name: JVC Responsible party: JVC AMERICAS CORP. Address: 1700 Valley Road Wayne, N. J. 07470 Telephone Number: 973-317-5000 This device complies with Part 15 of FCC Rules.
Terms A AC Adapter ................................................. 15, 42 M Manual Recording ..............................................24 AV Connection ............................................ 25, 34 Menu Settings .................................................... 37 B Backlight Compensation ................................... 24 N Number of Images ............................................. 41 O On-screen Recording Control ........................... 19 Battery Pack ....................
Memo GZ-MS130BU_US_IB_SPB.
Precauciones de seguridad ADVERTENCIA: PARA EVITAR RIESGO DE INCENDIOS O ELECTROCUCIONES, NO EXPONGA ESTE APARATO A LA LLUVIA O HUMEDAD. NOTA: • La placa de valores nominales y la precaución • • de seguridad se encuentran en la parte inferior y/o en la parte posterior de la unidad principal. La placa del número de serie se encuentra en el compartimiento de la batería.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD 1. 2. 3. 4. 5. 6. 7. Lea estas instrucciones. Conserve estas instrucciones. Preste atención a las advertencias. Siga todas las instrucciones. No utilice este aparato cerca del agua. Limpie sólo con paño seco. No bloquee ninguna abertura de ventilación. Instale de acuerdo con las instrucciones del fabricante. 8. No lo instale cerca de ninguna fuente de calor tales como, radiadores, calefactores, cocinas, u otros aparatos (incluyendo amplificadores) que produzcan calor.
Guía de inicio fácil Cargue la batería antes de grabar Apague la videocamara y coloque la batería. Indicador de acceso Parpadea: se está accediendo a los archivos Luz de alimentacion/carga Parpadea: carga en curso Se apaga: carga terminada No retire el adaptador de ca ni la batería o la tarjeta SD mientras el indicador esté parpadeando. Abra la tapa Batería La batería no está cargada en el momento de la compra.
Ajuste de la fecha/hora Q Abra la pantalla de LCD para encender la videocámara. S Seleccione [CONF. RELOJ] AJUS.RELOJ CONF. RELOJ CONF. ÁREA CONF. PARA HORARIO DE VERANO CONF. LA HORA, CIUDAD Y HORA SALIR AJUSTE Botón de alimentación la ciudad que se encuentre situada T Seleccione más cerca del área en la que vaya a utilizar la videocámara. CONF. ÁREA Pantalla LCD Seleccione [SÍ] antes que transcurran 10 R desegundos Deslice el dedo hacia arriba y hacia abajo sobre el sensor.
Grabación de vídeo PRECAUCIÓN Antes de grabar una escena importante, es recomendable llevar a cabo una grabación de prueba. el interruptor de modo Q Deslice para seleccionar el modo ! (vídeo). R Seleccione el modo de grabación PLAY/REC El modo cambiará cuando pulse el botón. Se mostrará el indicador de grabación automática. [ 4 h 59 m ] 0 : 04 : 01 S M Inicie la grabación Pulse el botón START/STOP para iniciar la grabación y púlselo de nuevo para detenerla.
Reproducción Q Seleccione el modo de reproducción PLAY/REC El modo cambiará cuando pulse el botón. R Seleccione el archivo que desee Pantalla de índice OPERACIÓN TÁCTIL REPRODUCCIÓN VÍDEO 1/2 NOV.01.2009 04:55PM DIGEST S Seleccione F (Toque OK) LASER TOUCH OPERATION Pantalla de reproducción L Para llevar a cabo operaciones como la búsqueda hacia delante o hacia atrás ( pág. 22) L Para visualizar archivos en el televisor ( pág.
Contenido PREPARATIVOS USO CON EL TELEVISOR Índice ..................................................... 10 Accesorios ............................................ 12 Visualización de archivos en un televisor.............................................. 25 Colocación del filtro de ferrita ...................... 12 Preparación del mando a distancia ............. 12 Conexión con el televisor............................. 25 Operación de reproducción .........................
Cómo utilizar el sensor táctil Una vez se muestre el menú en el monitor LCD: Realice una copia de seguridad de los datos importantes que haya grabado VÍDEO AJUSTE MANUAL SALIR Es recomendable que efectúe una copia de sus datos grabados importantes en un DVD u otro soporte de grabación para el almacenamiento. JVC no se hará responsable de la pérdida de sus datos.
GETTING STARTED Índice DC NOTA • La pantalla LCD puede girar 270°. • Procure no tapar 4, 5, 7 y 8 durante la filmación. SP10 GZ-MS130BU_US_IB_SPB.
Videocámara Sensor de la cámara Indicador luminoso ( p. 21) Cubierta del objetivo Objetivo Micrófono estéreo Y Z a b Botón S.
Accesorios o Adaptador de CA AP-V20U/AP-V14U* Cable USB CD-ROM Batería BN-VF808U Filtro de ferrita (x2) Cable de audio/vídeo Mando a distancia RM-V751U Pila de litio CR-2025 Preinstalada en el mando a distancia. NOTA Asegúrese de utilizar los cables suministrados para las conexiones. No utilice ningún otro cable. * El modelo AP-V14U no se menciona en la GUÍA incluida en el CD-ROM suministrado.
Indicaciones en la pantalla LCD Durante la grabación de vídeo e imágenes fijas Sólo durante la grabación de vídeo [4h59m] 1/4000 0 W SD 4:55 PM EDICIÓN COPIA FUNCIONAMIENTO DE PC Sólo durante la grabación de imágenes fijas USING WITH TV ! Indicador del modo de funcionamiento seleccionado ( p. 24) 4 : Modo automático 3 : Modo manual # Indicador de modo de efectos especiales $ Indicador de modo telemacro % Indicador de luz LED ( pg.
Indicaciones en la pantalla LCD (continuación) Durante la reproducción de vídeo Durante la reproducción de imágenes fijas 1: 55 : 01 +4 SD 101- 0098 SD 8 NOV. 1. 2009 4:55 PM NOV. 1. 2009 ! Indicador de modo # Indicador de reproducción de lista de reproducción (Aparece al reproducir una lista de reproducción.
Ajustes preliminares necesarios L Para comprobar el nivel de carga de la Carga de la batería 1 Coloque la batería y, a continuación, conecte el adaptador de ca. • Con la marca “v” (flecha) de la batería Conector de CC Tiempo de carga Tiempo de grabación BN-VF808U (suministrada) 1 hr. 50 min. 2 hr. 45 min.* BN-VF815U 2 hr. 40 min. 5 hr. 25 min.* BN-VF823U 3 hr. 40 min. 8 hr. 10 min.
Otros ajustes CONF. PARA HORARIO DE VERANO Ajuste de la fecha/hora HORARIO DE VERANO OFF 1 2 3 Abra la pantalla de LCD para encender la videocámara. NOV.1.2009 04:55PM CONF. HORARIO DE VERANO SALIR AJUSTE 8 Toque MENÚ. Seleccione el elemento mediante el sensor táctil y seleccione [}] para efectuar el ajuste. Seleccione [CONFIG. PANTALLA]. VÍDEO SIN VIENTO CAMB AUTO MEDIO GRAB CONFIG. PANTALLA > CONFIG. BÁSICA > Ajuste la fecha y la hora. CONF. RELOJ FECHA CONFIGURE PARÁ. VIS.
Ajuste del idioma Instalación en trípode El idioma en el que se muestra la información de la pantalla puede cambiarse. Toque MENÚ. Base de la videocámara Seleccione [CONFIG. PANTALLA]. GRABACIÓN/ REPRODUCCIÓN 2 3 Abra la pantalla de LCD para encender la videocámara. VÍDEO SIN VIENTO CAMB AUTO MEDIO GRAB CONFIG. PANTALLA > CONFIG.
Otros ajustes (continuación) NOTA Utilización de una tarjeta SD Si desea grabar en una tarjeta de memoria SD, debe realizar las siguientes operaciones. • Se ha confirmado el funcionamiento con las siguientes tarjetas de memoria SD. Tarjeta de memoria SD o SDHC compatible con: clase 4 o superior Tarjetas de memoria SD, Panasonic, TOSHIBA, SanDisk o ATP (256 MB a 2 GB) o tarjeta de memoria SDHC (4 GB a 32 GB).
Grabación de archivos Grabación de vídeo Pulse el botón PLAY/REC para seleccionar el modo de grabación. PLAY/REC Pulse el botón START/STOP para empezar la grabación. [4 h 59 m] 0:00:01 REC FUNCIONAMIENTO DE PC Cambie los ajustes en [CALIDAD DE VÍDEO]. L Para cambiar la relación de aspecto de la imagen (16:9/4:3) Cambie los ajustes en [SELECC. REL. ASPECTO]. COPIA L Para cambiar la calidad de la imagen grabada Seleccione A mientras la grabación se encuentra en modo de pausa.
Grabación de archivos (continuación) Grabación de imágenes fijas Deslice el interruptor de modo para seleccionar el modo # (imagen fija). Pulse el botón PLAY/REC para seleccionar el modo de grabación. PLAY/REC FINE [9999] Mantenga pulsado el botón SNAPSHOT hasta la mitad de su recorrido. FINE El indicador ? se vuelve verde cuando la imagen capturada queda enfocada. L Para visualizar la última imagen grabada Seleccione A tras tomar la fotografía.
Uso del zoom DIRECT DVD T: Telefoto ! mode # mode [80X/DIGITAL] [35X/ÓPTICA] ESTADO DE LA BATERÍA 100% TIEMPO MÁX min 50% INFO 0% SALIR L Para volver a la pantalla normal Seleccione [SALIR] o pulse INFO. NOTA L Para cambiar el porcentaje de zoom NOTA Luz LED 1 2 3 Preparativos: • Deslice el interruptor de modo para seleccionar el modo !. • Pulse el botón PLAY/REC para seleccionar el modo de grabación. Pulse el botón INFO una vez (MEMORIA INTEGRADA) o dos veces (TARJETA SD).
Reproducción de archivos Reproducción de vídeo Deslice el selector de modo para seleccionar el modo ! (video). Pulse PLAY/REC para seleccionar el modo de reproducción. REPRODUCCIÓN VÍDEO 1/2 PLAY/REC NOV.01.2009 04:55PM DIGEST Aparecerá la pantalla de índice. Seleccione el archivo que desee. L Para moverse a la página anterior o a la siguiente Toque [v] o [V] durante más de un segundo. L Para reproducir unos segundos de cada escena seleccionada de los vídeos grabados Toque [DIGEST].
Reproducción de imágenes fijas Pulse PLAY/REC para seleccionar el modo de reproducción. REPROD. IMÁGENES 1/2 PLAY/REC NOV.01.2009 04:55PM Seleccione el archivo que desee. GRABACIÓN/ REPRODUCCIÓN Aparecerá la pantalla de índice. PREPARATIVOS Deslice el selector de modo para seleccionar el modo # (imágenes fijas). USING WITH TV EDICIÓN L Para moverse a la página anterior o a la COPIA siguiente Toque [v] o [V] durante más de un segundo. L Para eliminar una imagen fija Seleccione $.
Grabación manual El modo de grabación manual permite ajustar manualmente el enfoque, el brillo de la pantalla, etc. Cambio al modo de grabación manual Preparativos: • Deslice el interruptor de modo para seleccionar el modo ! o #. • Pulse el botón PLAY/REC para seleccionar el modo de grabación. Ajuste manual en el menú En el modo de grabación manual: 1 Toque MENU. 2 Seleccione [AJUSTE MANUAL]. VÍDEO AJUSTE MANUAL ILUMINACIÓN REGISTRAR EVENTO CALIDAD DE VÍDEO USE CONFIG.
Visualización de archivos en el televisor Esta camara esta disenada para ser utilizada con senales de television en color tipo NTSC. Nose puede usar con un televisor de otra norma. L Para efectuar la conexión mediante el conector de AV. Conector de cc 1 Encienda la videocámara y el televisor. 2 Ajuste el televisor en el modo de vídeo. 3 Encienda la videograbadora o la grabadora de DVD y ajústelas en el modo de entrada AUX.
EDITING/PRINTING Gestión de archivos PRECAUCIÓN No desconecte el soporte de grabación ni lleve a cabo ninguna otra operación (como desactivar la alimentación) mientras se accede a los archivos. Asimismo, asegúrese de utilizar el adaptador de alimentación de ca suministrado, ya que es posible que los datos del soporte de grabación se dañen si la batería se agota durante el funcionamiento. Si se dañan los datos del soporte de grabación, formatee el soporte de grabación para volver a utilizarlo.
COPYING Copia de archivos Es recomendable que efectúe una copia de sus datos grabados importantes en un DVD u otro soporte de grabación para el almacenamiento. JVC no se hará responsable de la pérdida de sus datos. que se puedan utilizar. También es posible utilizar discos DVD-RW usados, pero es necesario formatearlos antes de efectuar la grabación. Al formatear un disco se elimina todo el contenido grabado en este hasta el momento. • No es posible utilizar discos de doble capa.
Copia de archivos (continuación) Copia de seguridad de todos los archivos 5 • Los archivos se copian en el disco. Cuando se muestre el mensaje [TERMINADO], toque OK. Preparativos: • Conecte la videocámara a la grabadora de DVD. • Deslice el interruptor de modo para seleccionar el modo !. 1 • Cuando se muestre el mensaje [INSERTAR SIGUIENTE DISCO PULSAR [CANCELAR] PARA ABANDONAR LA CREACIÓN], cambie el disco. Los archivos restantes se copiarán en el segundo disco.
Creación de discos DVD mediante un ordenador 1 Haga clic en [Easy Installation]. PREPARATIVOS Lea, por favor, “Convenio de licencia del software de JVC” de las instrucciones del CDROM antes de instalar el software. Es posible copiar los datos de la videocámara y crear un DVD utilizando un PC. Preparativos: Cargue el CD-ROM suministrado en el ordenador. En Windows Vista, se mostrará el cuadro de diálogo de reproducción automática.
Copia de archivos (continuación) El software Everio MediaBrowser se iniciará en el ordenador. R Realización de una copia de seguridad en el ordenador Preparativos: • Instale el software en el ordenador. • Asegurese de que dispone de suficiente espacio libre en el disco duro del PC HDD. • Cierre el monitor LCD para apagar la videocámara. 3 Conector de cc Adaptador de CA Haga clic en [Todo el volumen en la videocamara] y en [Proximo]. A la toma de CA DC 4 Haga clic en [Comienzo].
S Realización de listas de usuarios para ordenar los archivos 5 Haga doble clic en la fecha de grabación. PREPARATIVOS Es posible efectuar una lista de usuarios de un determinado asunto (por ejemplo, de un viaje, una competición de atletismo) y colocar los archivos relacionados con el asunto en la lista de usuarios. 1 Se visualizarán los archivos grabados en el día seleccionado. 6 Arrastre el archivo y suéltelo en la lista de usuarios. Seleccione [Solo filmes].
Copia de archivos (continuación) T Copia de archivos en un disco DVD 4 Preparativos: Utilice un disco DVD en el que se pueda grabar (es recomendable utilizar discos DVD-R). 1 Seleccione la lista de usuarios y haga clic en [Crear disco]. 5 2 Haga clic en [Comienzo]. Haga clic en [Selecciona los archivos individualmente] y haga clic en [Proximo]. Para anadir todos los archivos en discos DVD, haga clic en [Seleccionar todos los archivos visualizados] y vaya al paso 4.
Estructura de carpetas y extensiones Soporte de grabación [DCIM] X = número Contiene las carpetas de imágenes fijas. [XXXJVCSO] Contiene las carpetas de archivos de vídeo. Información de gestión* del soporte en conjunto [PRGXXX] [PRGXXX.PGI] [MOVXXX.MOD] [MOVXXX.MOI] Información de gestión* Archivo de vídeo Información de gestión* de los archivos de vídeo [PRGXXX] EDICIÓN El archivo de vídeo con información de gestión está dañado.
Copia de archivos (continuación) Copia de archivos en uns grabadora de vídeo/DVD 1 2 Preparativos: • Crear una lista de reproducción. • Apague todas las unidades. Ajuste la grabadora de vídeo o de DVD en el modo de entrada AUX. Compruebe que las imágenes de la videocámara se reciben correctamente en la videograbadora y en la grabadora de DVD. L Para efectuar la conexión mediante los conectores de AV (copia analógica) Conector de cc Abra el monitor LCD para encender la videocámara.
Utilización con un reproductor multimedia portátil Activación del modo de exportación EXPORT LIB. 1/3 LIB. SD LIB. CHECK SALIR • Para comprobar el contenido del archivo, seleccione [CHECK]. 3 Seleccione [SALIR]. L Para cancelar el ajuste de la exportación Seleccione el archivo y pulse [LIB.] de nuevo. L Para salir de la pantalla 1) Seleccione [SALIR]. 2) Seleccione [SÍ]. ON L Para desactivar el modo de exportación Pulse EXPORT dos veces.
Carga de archivos a sitios web Activación del modo de carga Carga de archivos You Tube=website:http://www.youtube.com/ Es posible cargar el archivo en sitios web para compartir vídeo (You TubeTM) de manera rápida después de efectuar la grabación. Para obtener más información acerca de YouTube™, visite el sitio web de YouTube™: http://www.youtube.com/ Para obtener más información acerca de la carga de archivos, consulte el manual de instrucciones del software MediaBrowser contenido en el CD-ROM.
MENU SETTINGS Cambio de las configuraciones de menús 1 Toque MENU. 3 2 Seleccione el menú que desee. Seleccione el ajuste que desee. VÍDEO REGISTER EVENT OFF VIDEO QUALITY ZOOMON ON VÍDEO DIS DIS SALIR ON IMAGEN BORROSA. TIENE QUE AJUSTE ON IMAGE BLURRED NEED TO AJUSTE SALIR L Para volver a la pantalla anterior Seleccione @. L Para salir de la pantalla FUNCIONAMIENTO DE PC Alimentación No hay alimentación. Visualizaciones El monitor LCD resulta difícil de visualizar.
Solución de problemas (continuación) Problema Grabación La grabación no puede realizarse. Acción • La tarjeta SD o la memoria integrada están llenas. Elimine los archivos innecesarios o sustituya la tarjeta SD. • Introduzca una tarjeta SD disponible en el mercado y ajuste La grabación se detiene automáticamente. El sonido o el vídeo se interrumpen. [SOPORTE GRAB. VÍDEO] en [TARJETA SD] y [SOPORTE GRAB. IMAGEN] en [SD].
Indicaciones de advertencia Indicación ¡AJUSTE FECHA/HORA! Acción • Permite ajustar el reloj. Si el mensaje sigue apareciendo después de ajustar el reloj, significa que la batería de este se ha agotado. Consulte con su distribuidor de JVC más cercano. • Asegúrese de utilizar baterías de JVC. NO FORMATEADO • Seleccione [ACEPTAR] y seleccione [SÍ] para realizar el • Compruebe el procedimiento operativo y vuelva a intentarlo. • Apague la videocámara y vuélvala a encender. ERROR ELIM.
Especificaciones Videocámara L Aspectos generales Fuente de alimentación eléctrica CC 11 V (con adaptador de CA) CC 7,2 V (con batería) Consumo eléctrico Aproximadamente 1.8 W* * Cuando la luz LED está apagada y la luz de fondo de la pantalla está ajustada en modo de [ESTÁNDAR]. Consumo de corriente nominal: 1 A Dimensiones (anchura x altura x fondo) 54.5 mm x 65 mm x 112.
Dimensiones (anchura x altura x fondo) Mando a distancia 42 mm x 14.5 mm x 91 mm Peso Fuente de alimentación eléctrica Aproximadamente 30 g (incluida la batería) DC 3 V Vida útil de la batería PREPARATIVOS Aproximadamente 1 año (en función de la frecuencia de uso) El diseño y las especificaciones están sujetas a modificaciones sin previo aviso. Distancia de funcionamiento Hasta 5 m Temperatura de funcionamiento 0°C a 40°C Soporte de grabación 256 MB 512 MB Calidad 3 m. 6 m.
Precauciones Adaptador de CA Si utiliza el adaptador de CA en países fuera de los EE.UU. El adaptador de CA suministrado tiene una función de selección automática de tensión en la escala de corriente alterna de 110 V a 240 V. USO DEL ENCHUFE ADAPTADOR DE CA En caso de conectar el cable de alimentación de la unidad a un tomacorriente de CA que no sea de la serie American National Standard C73, emplee un enchufe adaptador de CA, denominado “Siemens Plug”, como el mostrado.
Equipo principal • USING WITH TV EDICIÓN COPIA FUNCIONAMIENTO DE PC Los cambios o modificaciones no aprobados por JVC podrian anular la autoridad del usuario para utilizar el equipo. Este equipo ha sido examinado y cumple con los límites de dispositivos digitales Clase B, segun el Apartado 15 de la reglamentacion FCC. Estos limites estan diseñados para suministrar una protección razonable contra interferencias perjudiciales en una instalacion residencial.
Términos A L Adaptador de CA ......................................... 15, 42 Ajuste de la fecha/hora ...................................... 16 Ajuste del idioma ............................................... 17 Ajuste del reloj ................................................... 16 Luz LED ............................................................. 21 M Mando a distancia........................................ 10, 11 Memoria Integrada .......................................