JLIP VIDEO CAPTURE DOCKING STATION ENGLISH BASE DE MONTAGE A CAPTURE VIDEO JLIP FRANÇAIS GV-DS2 INSTRUCTIONS MODE D'EMPLOI For Customer Use: Enter below the Model No. and Serial No. which is located on the bottom of cabinet. Retain this information for future reference. Model No. Serial No.
EN Dear Customer, Thank you for purchasing this VIDEO CAPTURE DOCKING STATION. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of this product. Using This Instruction Manual • All major sections and subsections are listed in the Table Of Contents (Z pg. 7 – 9). • Notes appear after most subsections. Be sure to read these as well. • Basic and advanced features/operation are separated for easier reference. It is recommended that you . . .
EN IMPORTANT PRODUCT SAFETY INSTRUCTIONS Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing. ATTENTION: Follow and obey all warnings and instructions marked on your product and its operating instructions.
EN USE SERVICING 1. Accessories 1. Servicing To avoid personal injury: • Do not place this product on an unstable cart, stand, tripod, bracket or table. It may fall, causing serious injury to a child or adult, and serious damage to the product. • Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product. • Use a mounting accessory recommended by the manufacturer and follow the manufacturer’s instructions for any mounting of the product.
CAUTIONS EN 5 DO NOT attempt to insert foreign objects into the connectors, as this can lead to electric shock or fire. If an object is accidentally inserted, unplug it and contact your JVC dealer. Be especially careful with children. If during use you notice that the VIDEO CAPTURE DOCKING STATION is damaged, unplug it and contact your JVC dealer. Use of the VIDEO CAPTURE DOCKING STATION under these conditions can lead to fire or electric shock.
EN CAUTIONS (cont.) How to handle a CD-ROM ● Take care not to soil or scratch the mirror surface (opposite to the printed surface). Do not write anything or put a sticker on either the front or back surface. If the CD-ROM gets dirty, gently wipe it with a soft cloth outward from the center hole using a circular motion. ● Do not use conventional disc cleaners or cleaning spray. ● Do not bend the CD-ROM or touch its mirror surface. ● Do not store your CD-ROM in a dusty, hot or humid environment.
CONTENTS EN 7 MAJOR FEATURES 10 CONTROLS AND CONNECTORS 12 CAMCORDER ATTACHMENT 13 CONNECTIONS 14 JLIP VIDEO CAPTURE SOFTWARE SECTION ....... 17 GETTING STARTED 18 INSTALLATION (JLIP Video Capture Software) 19 OPEN & CLOSE (Basic Operation Procedure) 20 Preparation ....................................................................... 20 How to close the program ...................................................... 21 INITIALIZATION 22 Initializing JLIP .....................................
CONTENTS (cont.) EN SAVE PICTURE 36 Create new folder ................................................................ 36 Saving ............................................................................. 36 Open index ........................................................................ 37 Save the full image data ........................................................ 37 JLIP VIDEO PRODUCER SOFTWARE 38 Using JLIP video producer software data .....................................
EN 9 VIDEO PRINTER OPERATION (GV-PT1U) 62 Printing ............................................................................ 62 Adjusting picture equalization .................................................. 63 Quitting the “Video Printer” window ......................................... 63 Quitting the JLIP VIDEO PRODUCER window ................................ 63 VIDEO PRINTER OPERATION (GV-PT2U) 64 Auto capture ......................................................................
MAJOR FEATURES EN Advanced Applications Create title indexes for your video collection Title index images can be captured from your favorite recordings in intervals of 30 minutes, 1 hour, 1.5 hours, etc. using the Interval Capture mode. Print the captured index images on your PC printer using the computer’s Print Screen facility, then attach them to your cassettes. Business presentations Images captured from video can be incorporated into business documents to spice up your presentations.
EN 11 Two software programs are provided. JLIP Video Capture Software JLIP Video Producer Software (Z pg. 14 – 43) (Z pg. 14, 45 – 71) JLIP Video Capture Software JLIP Control Facility This is the software described in this manual.
EN CONTROLS AND CONNECTORS PLAY button STOP button PAUSE button Rewind (REW) button EDIT button Fast-Forward (FF) button LOCK lever JLIP jack Z pg. 15 (Joint Level Interface Protocol) • Connect to a JLIPcompatible comcorder or VCR to control it from the computer. RELEASE button DIGITAL jack Z pg. 15, 16 • Connect to the computer’s RS-232C terminal (COM port). Multi connector Z pg. 13 • The Docking Station can be connected with the GR-DVXU through this connector.
CAMCORDER ATTACHMENT EN 13 Before attachment, make sure the camcorder’s power is off. 1 1. OPEN COVER Slide the Multi connector cover (MULTI) on the bottom of the camcorder in the direction of the arrow until you hear a click. 2. ATTACH Attach the camcorder by aligning the mark on it with the one on the Video Capture Docking Station. 3. FIX 2 Slide the camcorder in the direction of the arrow. 4. LOCK While holding the camcorder, slide the LOCK lever in the direction of the arrow.
CONNECTIONS EN n To assure safety, make sure all units are turned off before making any connections. n The video images will be displayed on the LCD screen of the attached GR-DVXU series camcorder. You cannot view the images on the computer screen. n When connecting the cables (provided with this Video Capture Docking Station or with the camcorder), be sure to connect the terminals equipped with Core filters to the Video Capture Docking Station.
EN 15 n The Video Capture Docking Station does not receive power from the battery pack installed in the camcorder or from the AC Power Adapter/Charger attached to the camcorder. Be sure to connect the AA-V90U AC Power Adapter/Charger (exclusively for the Video Capture Docking Station) to the DC input jack located on the Video Capture Docking Station.
CONNECTIONS (cont.) EN WHEN USING A RECORDING DECK WITH NEITHER A JLIP CONNECTOR NOR A REMOTE PAUSE JACK When using the JLIP Video Producer Software . . . ● When using a recording deck with neither a JLIP connector nor a remote pause jack, set your VCR brand using the RM-V711U remote control unit then perform editing using the RMV711U. Also refer to pg. 61 to 64 of the camcorder’s instruction manual. ● For all connections except those to the digital connector and edit jack, Z pg. 14 and 15.
EN JLIP VIDEO CAPTURE SOFTWARE SECTION Operating Environment .............................................. 18 Connectable Devices ................................................. 18 Installation ............................................................ 19 Open & Close ......................................................... 20 Initialization .......................................................... 22 How The Desktop Works ........................................... 24 Video Capture ................
GETTING STARTED EN What is video capture software ? Video capture software is a type of application program that allows you to capture video images from camcorders and VCRs and store them in personal computers running under the WindowsT operating system. These images can be transferred from the video source to the computer via a standard RS-232C communication interface.
INSTALLATION (JLIP Video Capture Software) EN 19 WINDOWST 95 WINDOWST 3.1 Refer to the WindowsT 95 manual or your computer’s manual for details on basic WindowsT 95 operating procedures. Refer to the WindowsT 3.1 manual of or your computer manual for details on basic WindowsT 3.1 operating procedures. Installation Procedure Installation Procedure This software offers you the choise of viewing on-screen messages in English or French.
EN OPEN & CLOSE (Basic Operation Procedure) The Video Capture software can be started up in the same way as any other program running under Windows. The procedure differs slightly depending on whether you’re using WindowsT 3.1 or WindowsT 95. Preparation • • • • Turn on your computer. Turn on the video source units (such as camcorders and VCRs). If you want to capture a still picture from a recorded tape, load the tape into the video unit.
EN 21 HOW TO CLOSE THE PROGRAM Double-click the control menu button in WindowsT 3.1 or click “Exit” in the “File (F)” menu. In WindowsT 95, simply click the Close button. If you try to close the program with no image data saved, the message “The album has not been saved. Save?” appears. Please note that if you close without saving, all unsaved captured data will be deleted. 1. Click “Exit” from “File” in the menu bar. •The program closes.
INITIALIZATION EN INITIALIZING JLIP The first time you start the Video Capture software, JLIP initialization is required. This sets which of the computer’s COM ports (connector into which the RS-232C cable is plugged) is connected to the JLIP Video Capture Docking Station. The initialization window automatically appears the first time you start the software after installation. Do not forget to carry out this JLIP initialization procedure.
EN 23 SELECT UNITS 6. 7. Call up the “Device Selection” window. Click the name of the unit required. •The word “VCRCAMERA” appears in the VCR box to indicate the Video source unit is now in use. •The word “MODULE” appears in the Video Capture box to indicate the Video Capture Docking Station is now in use. •Only one VCR and one Video Capture device can be selected. 8. Click “OK”. •The main desktop window returns (setting complete).
HOW THE DESKTOP WORKS EN MAIN DESKTOP WINDOW 1 Menu bar 2 Control buttons Close button JLIP Video Capture [–Untitled Folder–] (Untitled) File Edit Set-up Window Help CAPTURE TRANSFER MEMORY INPUT JLIP 01 02 03 04 05 00:01:23:12 00:02:17:21 00:07:01:19 00:37:05:06 00:20:39:18 06 07 08 00:39:03:11 00:47:53:03 --:--:--:-- 3 Image display area 1 Menu bar Displays function menus. See the next page for detailed information. 2 Control buttons •CAPTURE button (Z pg.
EN 3 25 Image display area Each time you press the Capture button an index image is captured into the image area. Up to 99 images can be captured, with up to five images in one horizontal frame. Index images are provided to allow you to confirm that you have captured the images you want.
HOW THE DESKTOP WORKS (cont.) EN MENU BAR All program functions can be selected from the menus in the menu bar. Click any item in the menu bar to open the corresponding pulldown menu. Then click the desired command in the pulldown menu. Some menu entries are invalid depending on the program status. Invalid commands appear lighter than valid commands.
EN Set-up Capture Mode Image Format Device Change Pre-roll Initialize ID Change Counter Reset Window Arrange Index VCR 27 Two different modes available: Step by Step Capture and Automatic Capture (Z pg. 29, 30, 32). Selects image data format to be used in the transfer and capture mode (Z pg. 33). To initialize a connected unit or to change a connected unit (Z pg. 23). Adjusts the Preroll time of the playback VCR.
VIDEO CAPTURE EN CAPTURING VIDEO IMAGES There are three capture modes available: Step by Step, Program and Interval. Image data flow Digital camcorder Video signal GV-DS2U (Image stored in video memory) Full image data (with a resolution of 640 x 480 pixels) 2 types of video data • Bitmap data Approx. 900 kB • JPEG video compression data Approx.
EN 29 STEP BY STEP CAPTURE Use the Step by Step Capture mode when you want to: •Capture a smaller number of images. •Confirm the images being captured. Preparation Set-up Capture Mode Image Format Device Change Pre-roll Initialize ID Change Counter Reset •Make sure all units are properly connected (Z pg. 14). •Click “Image Format” in “Set-up” and select the desired format (Z pg. 33).
VIDEO CAPTURE (cont.) EN AUTOMATIC CAPTURE There are two types of automatic capture: Program mode and Interval mode. You can save time in either mode because, once the initial settings have been stored or you have decided what pictures to capture, the subsequent capture process is carried out automatically. PROGRAM CAPTURE In the Program Capture mode, select the images you want to capture, and the JLIP Video Capture Docking Station will automatically capture and transfer the images to your computer.
EN VCR I 00:01:23:12F Capture Transfer 31 Click “Window” — “VCR” to call up the 4 VCR Operation window. the video source unit via the 5 Operate VCR Operation window. the “Capture” button on the 6 Click desired video image, and index image data (80 x 60 pixels) is transferred to the computer. •The message “No.1 index image being transferred” appears during data transmission. 7 Repeat steps 4 through 6 as necessary. “Transfer” button.
VIDEO CAPTURE (cont.) EN INTERVAL CAPTURE The Interval Capture mode is best suited for capturing images at set intervals from a camcorder. Set-up Capture Mode Image Format Device Change Pre-roll Initialize ID Change Counter Reset Step by Step Automatic VCR I 00:01:23:12F Capture Transfer NOTE: • Make sure that enough hard disk space is available on your computer before executing video transfer. For full image data space requirements, Z pg. 28.
PICTURE FORMAT SETTING EN 33 SELECTING A PICTURE FORMAT Under “Image Format”, you can specify the full image data format and the capture mode. the menu bar 1 Open and click “Set-up” — “Image Format”. •The “Image Format” window appears. Set-up Capture Mode Image Format Device Change Pre-roll Initialize ID Change Counter Reset format. 2 Select •There are two different settings avail- capture mode. 3 Select •There are two different settings available: “Frame Picture” and “Field Picture”.
ADDITIONAL OPERATIONS EN COUNTER VALUE CHANGE If you want to replace a captured image with a different one, you can capture the new one by changing the counter value. 02 the image display box of the index 1 Click number you want to change. •The box is bordered in green. 00:02:17:21 the menu bar and click “Edit” — 2 Open “Modify…”. •The “Modify Capture Point” window appears. Edit Transfer the Index Image Transfer the Full Image Modify… Delete Del 02 00:01:23:12 a new counter value. 3 Enter “OK”.
EN 35 DELETE INDEX IMAGE AND FULL IMAGE You can delete any captured picture. Both index image (80 x 60 pixels) and full image (640 x 480 pixels) are deleted. 02 the image display box you want to 1 Click delete. •The box is bordered in green. 00:02:17:21 the menu bar and click “Edit” — 2 Open “Delete”. •This deletes the selected image data. Edit Transfer the Index Image Transfer the Full Image Modify… Delete Del click “Window” — “Arrange 3 Then Index”.
SAVE PICTURE EN CREATE NEW FOLDER Creating a new folder (directory) is a good idea when capturing an image from another video tape. File Ctrl+N Ctrl+O Ctrl+S New Album Open Album Save Album Open JLIP (jlp) File Save As JLIP (jlp) File Save Image As… the menu bar and click “File” — 1 Open “New Album”. •The image display area is refreshed. •If the index image data on screen is not saved, you will be asked whether to save or not.
EN 37 OPEN INDEX File New Album Open Album Save Album Ctrl+N Ctrl+O Ctrl+S Open JLIP (jlp) File Save As JLIP (jlp) File Save Image As… Ctrl+A Exit the menu bar and click “File” — 1 Open “Open Album”. •The “Open Album” window appears. 2 Select the name of the folder (directory). 3 Click “OK”. SAVE THE FULL IMAGE DATA You can save a file under another name or in another folder so that you can edit it without losing the original.
EN JLIP VIDEO PRODUCER SOFTWARE USING JLIP VIDEO PRODUCER SOFTWARE DATA The Video Capture Docking Station can capture JLIP Video Producer software data at an edit-in point corresponding to a preset counter number. Preparation •Make sure all units are properly connected (Z pg. 14). •Insert the tape program edited with the Video Producer Software into the video source unit. •If the data is stored on a floppy disk, load disk into the floppy disk drive.
EN 39 HOW TO STORE JLIP VIDEO PRODUCER SOFTWARE DATA Data from this unit can be converted to JLIP Video Producer software files. If index image data is saved as a JLIP Video Producer software file, the file can be printed with the optional GV-PT1U/GV-PT2U Video Printer. Refer to the instruction manual for details. Preparation •Make sure all units are properly connected (Z pg. 14). •Insert a video tape into the video source unit.
TROUBLESHOOTING EN NOTE : External noise or disturbance may interfere with the microprocessors built into the JLIP Video Capture Docking Station. If this happens, turn the power off and then turn it on again. Problem Cause Page JLIP Video Capture Software does not work. v Does the JLIP Video Producer Software or the JLIP Movie Player Software run ? The JLIP Video Capture Software cannot run together with it. — Operating the camcorder (capturing video images through the computer etc.
EN 41 Problem Cause Page Cannot capture video data with the desired counter number. v There may be a slight difference between the counter of the video image that you want to capture and the Index image data/ Full image data captured in the computer. This is not a malfunction. 29 – 32 Counter cannot be reset. v Counter reset is not available with digital camcorders. 34 Program capture suddenly stops.
EN Message LIST OF ERROR MESSAGES v Appears when: m Action: Page COM port is not available. v Not connected to COM port set by JLIP Initialize. m Check the COM port number and connector and retry JLIP initialization. 22 Connected device not found. v Connected devices are not turned on. v Selected COM port is not connected properly. m Make sure connection is proper and carry out JLIP initialization. Then turn on this unit and the connected devices. 22, 23 Error — Transfer halted.
EN Message v Appears when: m Action: 43 Page Execute after playing back the VCR. v Video unit is not in Play mode during Interval Capture. m Click “OK”, set the video unit to Play and click “Transfer” again. Not enough disk space is available. v Remaining disk space is under 1 MB. m Click “OK”, check disk space and select a drive with space available with “Save Image As…”. — Communication error.
EN MEMO
EN 45 JLIP VIDEO PRODUCER SOFTWARE SECTION q The Readme.TXT file provides additional information for setup and information that is not included in the instruction manual. Please read the file before installing the provided software program. q You can find the latest information (in English) on the provided software program at our www server. http://www.jvc-victor.co.jp/index-e.
GETTING STARTED EN What is JLIP ? JLIP* stands for Joint Level Interface Protocol, a new communication protocol which allows AV units equipped with a JLIP terminal to be controlled by a personal computer. * is a registered trademark of JVC. Operating Environment ● Personal computer with MicrosoftT WindowsT 3.
INSTALLING (JLIP Video Producer Software) EN 47 WINDOWST 95 WINDOWST 3.1 Refer to the WindowsT 95 manual or your computer’s manual for details on basic WindowsT 95 operating procedures. Refer to the WindowsT 3.1 manual of or your computer manual for details on basic WindowsT 3.1 operating procedures. Installation Procedure Installation Procedure This software offers you the choise of viewing on-screen messages in English or French.
EN STARTING JLIP VIDEO PRODUCER SOFTWARE Starting JLIP Video Producer Software DEVICE(S) 1 PREPARE Turn the device(s) on and set the camcorder’s Power Dial to “PLAY”. VIDEO PRODUCER 2 ACCESS Double-click the JLIP VIDEO JLIP VIDEO PRODUCER PRODUCER icon and the Serial Port Selection dialog box appears. SERIAL PORT 3 SELECT Select the port number of the connector you are using to connect the computer to the Video Capture Docking Station. •If the connector number is A, B... A corresponds to 1.
EN DEVICE(S) 4 SELECT Click on the name of the device you Device Selection Select device to control. wish to control. Clicking “OK” brings up the JLIP VIDEO PRODUCER window. •It is possible to select a second device of a different type simultaneously, but it is impossible to select two same type devices simultaneously.
EN VIDEO PRODUCER WINDOW BUTTONS AND DISPLAYS 1. POWER button Control-menu box 4. ID number Title bar Menu bar 2. COUNTER system 5. FILE name Icon button 3. Tape counter display JLIP VIDEO PRODUCER File Edit Set-up Window Help Drop COUNTER POWER 00:00:00:09F ON OFF PROGRAM PLAYBACK SCENE CUT IN 06 ID FILE 6.
1. POWER button • Turns the device on and off. • If power is not supplied to the camcorder beforehand, you can not turn the camcorder on and off by clicking this button. • Some camcorders cannot be turned on and off by clicking this button. EN 11. Camcorder’s operation buttons • Operate the camcorder. Stop button REW/REW Search button Play button FF/FF Search button 2. COUNTER system Pause button • GR-DVXU series uses the Drop Frame system**. Reverse Slow button Forward Slow button 3.
BASIC OPERATIONS EN Operating camcorder Setting in/out points CAMCORDER 1 PREPARE Set the camcorder’s Power Dial to ON TV MONITOR 1 PLAYBACK Click . Playback picture appears on the “PLAY” and insert a recorded tape into the camcorder. 2 Click PLAYBACK ON TV MONITOR © TV monitor. CUT IN/OUT POINTS 2 SET Select “Function Set” from “Set-up” in the JLIP VIDEO PRODUCER window and select “Edit Tape”.
EN 53 Playing back one programmed scene JLIP VIDEO PRODUCER SCENE 1 SELECT Click on the line where the CUT IN/OUT File Edit Set-up Window Help Drop COUNTER POWER 00:00:00:09F ON OFF PROGRAM PLAYBACK SCENE CUT IN ID 06 FILE MEMO SCENE START BF WF B CUT OUT W BF 00:05:00:25 00:06:10:26 00:07:33:29 00:08:51:05 01 02 03 04 00:06:04:16 00:07:30:15 00:08:45:15 00:10:13:26 ELAPSED TIME TC BW 00:04:57:17F points you want to preview are displayed and that line will be highlighted.
BASIC OPERATIONS (cont.) EN Dubbing You can record all programmed scenes onto the tape in the recording deck.
EN 55 Saving the program list on hard disk It is possible to save all programmed scene information as a file in the computer. SAVING 1 START Select “Save As” from “File” on the JLIP JLIP VIDEO PRODUCER File Edit Set-up Window Help File New Ctrl+N Drop COUNTER Open Ctrl+O ON POWERCtrl+S Save Save As...
BASIC OPERATIONS (cont.) EN Opening a saved file Opening a file saved on floppy disk FOR FILE NAMES 1 LOOK Click “Open” from “File” on the JLIP VIDEO PRODUCER window. •The “Open a program list” dialog box appears. SELECT FILE NAME 2 Saved file names appear in the “FILE NAME” field. Click on the file name you want and it appears in the field above. FILE NAME 3 DETERMINE Click “OK” and the file will be read. FLOPPY DISK INTO 1 INSERT DRIVE DRIVE NUMBER 2 SELECT Click in “DRIVE”.
Copying a programmed scene and transferring it to an other position EN Transferring the programmed scene to an other position SCENE TO BE 1 DESIGNATE COPIED SCENE TO BE 1 DESIGNATE TRANSFERRED Click on the scene you want to copy. DESIGNATED SCENE IN 2 STORE MEMORY Choose “Copy” from “Edit”. POSITION 3 DESIGNATE Click on the scene number which is above the position to which the copied scene is to be transferred. COPIED SCENE 4 TRANSFER Choose “Paste” from “Edit”.
BASIC OPERATIONS (cont.) EN Selecting a P.AE/Effect There are 5 P.AE/Effects available to spice up the programmed scene. You can select only one effect per programmed scene. JLIP VIDEO PRODUCER File Edit Set-up Window Help Drop COUNTER POWER 00:00:00:09F ON OFF PROGRAM PLAYBACK SCENE CUT IN ID 06 FILE MEMO SCENE START BF WF B CUT OUT W SCENE 1 DESIGNATE Click on the scene where you want to use a P.AE/Effect.
EN P.AE/Effect buttons SEPIA Recorded scenes have a brownish tint like old photos. Combine this with the Cinema mode for a classic look. Fade/Wipe Effect buttons BF Fade in or out with a black screen. Adds a “ghost” to the subject, giving your recording a “fantasy” feeling. Wipe in on a black screen from the upper right to the lower left corner, or wipe out from lower left to upper right, leaving a black screen. STROBE WINDOW WIPE Your recording looks like a series of consecutive snapshots.
EN VIDEO PRINTER WINDOW BUTTONS AND DISPLAYS @À 2. POSITION button Title bar 7. STROBE SPEED button Icon button 1. POWER button Video Printer POWER ON ID OFF POSITION 16 STROBE 4 SELECTED OFF SAME HIGH LOW STROBE SPEED ON OFF PIX STABILIZER MULTI-PIX CONTENT 20 STORE PRINT SELECT SOURCE MEMORY Aperture Off ! ! 10. PRINT/EQ (equalization) button 11. SELECT (scene select) button 12. CLOSE button 6. CONTENT button 4. Message display 9. STORE button CLOSE 8.
EN 1. POWER button • Turns the device on and off. 2. POSITION button • Selects the position to store a scene in memory for Multi-Print. 3. ID number • Displays the selected device’s ID number. 4. Message display • Displays the operating mode of the selected device. 5. MULTI-PIX button • Select by clicking (¶ / Ä) button. OFF : Single print 4 : 4 shots on one sheet 16 : 16 shots on one sheet 6. CONTENT button • Select by clicking (¶ / Ä) button.
VIDEO PRINTER OPERATION (GV-PT1U) EN Printing Before printing, perform the procedure listed below. ● Connect to image and sound source (Z pg. 14, 15). ● Set VCR to external input. ● Set TV to VIDEO mode so that images from video printer appear. UP VIDEO PRINTER 1 BRING WINDOW SCENE 3 STORE Click “STORE” on the “Video Printer” Select “Video Printer” from “Window” on the JLIP VIDEO PRODUCER window. •The “Video Printer” window appears.
@@@ ÀÀÀ EN 63 Adjusting picture equalization You can adjust picture equalization; a feature not available on the video printer itself. Picture Equalization BRIGHTNESS 0 CONTRAST ON OFF OK APERTURE ON OFF CANCEL PICTURE 1 ACCESS EQUALIZATION DIALOG BOX Click “EQ” on the “Video Printer” window. •The “Picture Equalization” dialog box appears. ADJUSTMENT 2 DETERMINE After adjusting the items below, click “OK”. •The “Picture Equalization” dialog box closes.
VIDEO PRINTER OPERATION (GV-PT2U) EN Auto Capture Preparation • Load the tape into VCR. • Convert the captured data to JLIP Video Producer software data and store it (Z pg. 39). • Select file name (Z pg. 56). • Prepare for printing (refer to the GV-PT2U instruction manual). • Select desired layout using the remote control unit provided with the GV-PT2U. To Print Captured Video Data with Video Printer Captured video data can be automatically scanned and printed.
EN the Title bar in the JLIP VIDEO 3 Click PRODUCER window and activate the window.
ADVANCED OPERATIONS EN Changing ID number The device’s ID number is preset at factory as follows: ex. Camcorder: 06 or 07 Video printer: 20 When connecting more than two same type devices, the same ID numbers will exist and a malfunction can occur. To avoid a malfunction, change the ID numbers. It is recommended to change the ID number of an already connected device before connecting the same type device. “ID CHANGE” DIALOG ID NUMBER 1 ACCESS 4 SET BOX Click “OK”.
EN Changing the name of the device “NAME CHANGE” 1 ACCESS DIALOG BOX Choose “Name Change” from “Set-up” on the JLIP VIDEO PRODUCER window. •The “Name Change” dialog box appears. DEVICE 2 SELECT Click on the name of the device and “CHANGE”. •The dialog box to enter new name of the device appears. 3 ENTER NEW NAME NEW NAME 4 SET Click “OK”. Name Change Select the device to change. VCR CHANGE CLOSE VIDEO PRINTER CHANGE Name Change Enter new name (up to 20 letters).
ADVANCED OPERATIONS (cont.) EN Adjusting the gap between the stored edit-start point in the computer and the dubbed one in the recording deck During dubbing, the beginning of the scene stored in the computer can be missed or the scene prior to the transition you chose for the edit-start point can be dubbed into the recording deck. When these cases occur, adjust the gap for more accurate editing. EDIT-START TIMING DETERMINE VALUE 1 CHECK 4 After dubbing (Z pg. 54), play back the Click “OK”.
EN 69 Counter reset It is possible to reset the counter of the connected video device (VHS,VHS-C). JLIP VIDEO PRODUCER File Edit Set-up Set-up Window Help ID Change Drop COUNTER 00:06:38:11F Device Change NameON Change OFF POWER Recorder Select Record Timing PROGRAM PLAYBACK Pre-roll SCENE Counter CUTReset IN ID 00 FILE MEMO SCENE START BF WF B CUT OUT W Function Set Close Selial Initialize TC JLIP VIDEO PRODUCER window. •The connected recording deck counter is reset.
TROUBLESHOOTING EN MESSAGE v POSSIBLE CAUSE m CORRECTIVE ACTION Error – – This application will close. Check devices – – Confirm that power is ON. v The COM port used for the JLIP connector is not selected, or the COM port is selected but the connection is wrong. m Check the connected COM port and select it on the “Serial Port Selection” screen (Z pg. 48). No devices detected to connect. Power ON all devices in system. v Power is not supplied or the connection is wrong.
EN MESSAGE 71 v POSSIBLE CAUSE m CORRECTIVE ACTION Enter correct value. v You entered an incorrect device ID number. m Enter an ID number between 0 and 99 which is not being used by another device (Z pg. 66). Your selection is not valid. v The value of the CUT OUT point is smaller than the CUT IN point’s. m Set the value of the CUT OUT point so that it is larger than the CUT IN point’s (Z pg. 56). Set a value from 0 to 59. v You entered a value over 60. m Enter a value from 0 to 59 (Z pg. 56, 57).
MAJOR SPECIFICATIONS EN JLIP VIDEO CAPTURE DOCKING STATION Power consumption Connectors S-Video (S2 output) Video Audio JLIP (x 2) Digital Editing connector DC output : 9 W (when charging) : Output Y : 1.0 Vp-p, 75 ohms C : 0.29 Vp-p, 75 ohms : Output 1.0 Vp-p, 75 ohms (pin jack) (VIDEO output connector) : Output –8 dB, 1 kiloohm (pin jack) : 3.5 mm diameter, 4-pole, mini-head jack (compatible with EIAJ RC-5325 plug) : Mini DIN 8-pin : 3.
INDEX EN 73 A J Arrange Index ................................. Z pg. 35 Automatic Capture (AUTO) ....... Z pg. 30, 32 JPEG ................................................ Z pg. 33 B Bitmap ...................................... Z pg. 28, 33 C Capture Mode ................................. Z pg. 33 Change ID ................................ Z pg. 35, 66 COM Port ................................. Z pg. 22, 48 Counter reset .................................. Z pg. 34 Counter Value Change ............
GV-DS2 JVC COMPANY OF AMERICA DIVISION OF US JVC CORP. 41 Slater Drive, Elmwood Park, N.J. 07407 JVC CANADA INC. 21 Finchdene Square, Scarborough Ontario M1X 1A7 COPYRIGHT© 1997 VICTOR COMPANY OF JAPAN, LTD.
