User's Manual
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Assignment of Functions to User Buttons
- Tally Lamp and LED
- Recording Media
- Usable Cards
- Usable SSD Media
- Estimated Recordable Time of SD Cards
- Estimated Recordable Time of SSD Media
- Inserting an SD Card
- Removing the SD Card
- Switching the SD cards
- Inserting the SSD Media Adapter
- Formatting (Initializing) of Recording Media
- Repairing the Recording Media
- Clips Recorded to Recording Media
- About the Operation Lock Feature (KEYLOCK)
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Focusing by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Monitoring Audio Sound During Recording Using a Headphone
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing Time Code on Another Camera
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Histogram
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Configuring Infrared Recording
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Network
- Functions of Network Connection
- Preparing Network Connection
- Connecting to the Network
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Tagging Feature
- Overlay
- Others
Equalizer
You can
correct the characteristic and enhance the
sound of the connected microphone using this
equalizer setting.
For setting the audio frequency from a 5-band
equalizer.
0
Frequency:
100Hz, 330Hz, 1kHz, 3.3kHz, 10kHz
0
Variable level:
± 6dB (1dB step)
Memo :
0
Audio will be recorded in the characteristic set
in the equalizer.
0
Set all bands to “0 dB” to bypass the equalizer.
0
When the equalizer level is set to the + side, the
audio may be distorted. In this case, reduce the
recording level in Manual mode.
0
If the values of multiple frequencies are
changed, the specified levels and the actual
levels may be different due to interference
between the frequency bands.
0
This function is enabled only when both
[INPUT1/2 Wind Cut] and [Int. Mic Wind Cut] are
set to “Off”.
Monitor
For setting the audio sound of the [x] terminal to
stereo or mixed sound when the [MONITOR]
selection switch on the LCD monitor is set to
“BOTH”.
0
Mix:
Outputs mixed sound (mixed sound of CH1 and
CH2) to both L and R.
0
Stereo:
Outputs stereo sound (outputs audio sound of
CH1 to L, and CH2 to R).
[Setting Values: RMix, Stereo]
Memo :
0
If both CH1 and CH2 are built-in microphones,
stereo sound is output from the [x] terminal
regardless of the [Monitor]
setting.
IFB/RET Monitor...
9
CH1(/2)
For configuring the output from the [x] terminal
during IFB Return over IP of each channel.
0
Auto:
Outputs upon mixing the IFB/Return over IP
audio with the microphone audio when IFB/
Return over IP audio input is detected. Outputs
only the microphone audio when IFB/Return
over IP audio input is not detected.
0
IFB/RET Only:
Outputs only the IFB/Return over IP audio at all
times.
0
Off:
IFB/Return over IP audio is not output.
[Setting Values: RAuto, IFB/RET Only, Off]
Memo :
0
To
enable
different settings for CH1 and CH2 of
[IFB/RET Monitor], set [Monitor] to “Stereo”.
Alarm Level
For selecting whether to turn on the warning tone
as well as setting the volume.
The warning tone is output from the monitor
speaker or [x] terminal.
[Setting Values: RHigh, Middle, Low, Off]
Audio On FULL AUTO
For setting whether to enable Auto for audio when
the [FULL AUTO] switch is set to “ON”.
0
Auto:
Sets audio recording mode to the auto mode.
0
SW Set:
Sets the audio recording mode following the
[CH1/CH2 AUTO/MANUAL] selection switch
setting.
[Setting Values: RAuto, SW Set]
134
A/V Set Menu
Menu Display and Detailed Settings