INSTRUCTIONS
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
o Phase Items to Synchronize
The phase items to be synchronized may vary
depending on the input synchronizing signal and
output video signal.
Output Video Signal
Input Synchronizing
Signal
BB Tri-sync
720p 1080i
VIDEO Composite H, V, F V V, F
SDI
SD-SDI H, V, F V V, F
HD-SDI
720p
V H, V V
HD-SDI
1080i
V, F V H, V, F
H
:
Horizontal Phase
V
:
Vertical Phase
F
:
Field Phase
For digital signals (SDI) input
Input external synchronizing signals from the
[HD/SD SDI IN] terminal, and synchronize the
camera video or playback image with the external
signal.
Input external synchronizing signals from the
[HD/SD SDI IN] terminal, and synchronize the
camera video with the external signal.
o Synchronizing signal used
SD synchronizing
signal
:
Supports SMPTE259M
HD synchronizing
signal
:
Supports SMPTE ST296
3G-SDI
synchronizing
signal
:
Supports SMPTE ST424
.
+'6'6',,1
External Synchronizing Signal
SYNC Signal
Generator
1
Set the camera recorder to the Camera
mode.
(A P20 [Operation Modes] )
2
Set [Genlock Input
] to “SDI IN”.
Set [A/V Set] B
[Video Set] B [Genlock Input] to
“SDI IN”.
(A P134 [ Genlock Input ] )
Memo :
0
Set to “Adapter” to input synchronizing signal
from the accessory connection terminal (68
pins) on the rear of this unit.
3
When in the standby or stop mode, input
synchronizing signals from the SDI signal
generator to the [HD/SD SDI IN
] terminal.
0
When the
camera recorder’s video is locking
to the external synchronizing signal, “Sync
Locking” appears on the screen.
0
After locking to the external synchronizing
signal is complete, the display disappears
and recording can be performed.
0
If there is genlock signal input but the signal
format is not supported,
“Invalid Sync” is
displayed.
Memo :
0
If the frame rate in [WFrame & Bit Rate]/
[YFrame & Bit Rate] in the [Record Format]
menu is set to “60p
”, “60i” or “30p”, 59.94 Hz
synchronizing signals (vertical synchronization)
are input.
50 Hz/60 Hz synchronizing signals are not
synchronized.
0
If the frame rate of [WFrame & Bit Rate]/
[YFrame & Bit Rate] in the
[
Record Format]
menu is set to “50p”, “50i”, or “25p”, 50 Hz
synchronizing signals (vertical synchronization)
are input.
59.94 Hz/60 Hz synchronizing signals are not
synchronized.
(A P
152 [ W Frame Rate ] )
0
Do not
connect or disconnect the input cable for
the synchronizing signals during recording or
playback
0
If the power is turned on during input of external
synchronizing signals, vertical oscillation may
occur. This is not a malfunction.
0
Signals such as VTR playback signals with
jitters may not be synchronized on this camera
recorder.
0
Only H (Horizontal) and V (Vertical) genlock
functions are available on this camera recorder.
It does not come with a lock function for SC (sub-
carrier). Color flash may occur during switching
such as when composite signals are used by a
switcher.
Inputting External Synchronizing Signals (Genlock)
183
Connecting External Devices