User's Manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
9
Top 1
For setting
the maximum luminance level to display
Zebra1.
[Setting Values: Over, 100%, 98%, 95% to 5% (in
5% increments)] (R80%)
9
Bottom 1
For setting
the minimum luminance level to display
Zebra1.
[Setting Values: 100%, 98%, 95% to 0% (in 5%
increments)] (R70%)
9
Top 2
For setting
the maximum luminance level to display
Zebra2.
[Setting Values: Over, 100%, 98%, 95% to 5% (in
5% increments)] (ROver)
Memo :
0
This item
cannot be selected when [Zebra] is set
to “1 Pattern”.
9
Bottom 2
For setting
the minimum luminance level to display
Zebra2.
[Setting Values: 100%, 98%, 95% to 0% (in 5%
increments)] (R80%)
Memo :
0
This item
cannot be selected when [Zebra] is set
to “1 Pattern”.
Peaking Frequency
For configuring the frequency band for applying
outline enhancement
using [LCD Peaking] and the
[PEAKING] adjustment knob on the viewfinder.
[Setting Values: High, RMiddle, Low]
Video Signal Monitor
For configuring
whether to display or hide the video
signal monitor.
[Setting Values: On, ROff]
Memo :
0
This may not be selectable depending on the
operating mode and status.
9
Type
For configuring the video signal monitor to be
displayed.
0
Histogram2:
Displays the distribution of points in the image
based on the degree of brightness and the
corresponding number of points.
0
Vector Scope:
Displays the saturation and hue of the video as
a circle.
0
Waveform:
Displays the luminance signal of the video as a
waveform.
[Setting Values: Histogram2, Vector Scope,
RWaveform]
9
Histogram Top 2
For selecting the maximum brightness limit for
changing the histogram display color.
[Setting Values: 5% to 110% (in 5% increments)]
(R 80%)
0
When [
Color Space
] is set to “J-Log1”
[Setting Values: -5F-stop, -4F-stop, -3F-stop(2%),
-2F-stop, -1F-stop, 0F-stop(18%), ⅓F-stop, ⅔F-
stop, 1F-stop, 1⅓F-stop, 1⅔F-stop, 2F-stop, 2 ⅓
F-stop(90%), 2 ⅔ F-stop, R
3F-stop, 3 ⅓ F-stop, 3
⅔ F-stop, 4F-stop, 4 ⅓ F-stop, 4 ⅔ F-stop, 5F-
stop, 5 ⅓ F-stop, 5½F-stop]
Memo :
0
When [Color Space] is set to “J-Log1”, a green
line appears which corresponds to the 0F-stop
(18%) portion of the subject with 18%
reflectance.
9
Histogram Bottom 2
For selecting the minimum brightness limit for
changing the histogram display color.
[Setting Values: 0% to 105% (in 5% increments)]
(R 20%)
0
When [Color Space
]
is set to “J-Log1”
[Setting Values: -6F-stop, -5F-stop, -4F-stop,
R-3F-stop(2%), -2F-stop,
-1F-stop, 0F-stop(18%),
⅓ F-stop, ⅔ F-stop, 1F-stop, 1 ⅓ F-stop, 1 ⅔ F-
stop, 2F-stop, 2 ⅓ F-stop(90%), 2 ⅔ F-stop, 3F-
stop, 3 ⅓ F-stop, 3 ⅔ F-stop, 4F-stop, 4 ⅓ F-stop,
4 ⅔ F-stop, 5F-stop, 5 ⅓ F-stop]
Memo :
0
When [Color Space] is set to “J-Log1”, a green
line appears which corresponds to the 0F-stop
(18%) portion of the subject with 18%
reflectance.
LCD/VF Menu
127
Menu Display and Detailed Settings