User's Manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
o
When [System] is set to “SD” or “SD(SDI In)”:
2
Record Format
W
Format
W
Resolution
W
Frame
Rate
W
Bit Rate
W
Audio
QuickTime
(H.264)
720x480 60i
(U model)
8M (HQ) 4CH 16 bit/
2CH 16 bit
720x576 50i
(E model)
Memo :
0
Each item for slot B is fixed at the same setting
as slot A.
o
When [System
] is set to “HD+Web”, the options
for slot B are 2:
Record Format
Y
Format
Y
Resolution
Y
Frame
Rate
Y
Bit Rate
Y
Audio
QuickTime
(H.264)
960x540 30p, 25p,
24p
3M (HQ) 4CH/
2CH
720x480 60i 8M (HQ)
4CH 16 bit/
2CH 16 bit
720x576 50i 8M (HQ)
480x270 30p, 25p,
24p
1.2M (LP) 4CH/
2CH
Memo :
0
The following functions cannot be used when
HD+Web is selected.
View Remote, Live Streaming, Return over IP
Selecting the Aspect Ratio of SD Videos
2
For setting the aspect ratio of the recorded image
when [System] is set to “SD” or “SD(SDI In)”.
You can select “16:9”
or “4:3”.
Memo :
0
For conditions
other than those above, this item
is fixed at “16:9”.
Zoom Operation
Adjusts the angle of view.
Zooming can be operated using the following.
0
Zoom ring/zoom lever on the commercially
available lens
0
User buttons assigned with “Zoom Tele” and
“Zoom Wide
”
During the zoom operation, the zoom bar or
number
will
appear on the upper right corner of the
screen.
(A P164 [Zoom Display] )
Caution :
0
Depending on the zoom speed, the zoom drive
noise of the power zoom may be recorded.
Using Zoom Ring/Zoom Lever on
Commercially Available Lens
You can adjust the preferred angle of view by
turning the zoom ring or operating the zoom lever.
Memo :
0
For details on the lens, please refer to the
“INSTRUCTIONS” of the lens used.
Using User Buttons Assigned with
“Zoom Tele” and
“Zoom Wide”
1
Assign “Zoom Tele” and “Zoom Wide” to
the user buttons.
(A P45 [Assignment of Functions to User
Buttons] )
(A P111 [User Switch Set Item] )
0
Configure the zoom speed of the user
buttons in
[Camera Function] B [User Switch
Set] B [Zoom Speed].
Increasing the value increases the zoom
speed.
2
Press the user button assigned with “Zoom
Tele”
/“Zoom Wide” to zoom.
0
The zoom operation is performed in the
speed that has been set.
Memo :
0
This function may not work depending on the
lens attached.
Selecting System Definition, File Format and Video Format
57
Shooting