INSTRUCTIONS
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
Connecting via SDI
0
Digital video signals, together with embedded
(superimposed) audio signals and time code
signals, are output for both the 3G-SDI/HD-SDI
and SD-SDI signals.
Memo :
0
The sampling frequency for embedded
(superimposed) audio signals is 48 kHz. Time
code of the built-in time generator as well as
playback time code are also output.
Setting the Aspect
0
For setting the mode to convert images with a
16:9 aspect
ratio to display on a 4:3 aspect ratio
screen.
0
Set using [A/V Set] B [Video Set] B [SD
Aspect].
0
The
available
modes include “Side Cut”, “Letter”
(blackened at the top and bottom), and
“Squeeze” (full size, compressed at the left and
right).
(A P134
[ SD Aspect ] )
Memo :
0
When [Record Format]
B
[System] is set to “SD”,
and [SD Aspect] is set to “4:3”, this item cannot be
selected.
0
When [Record Format] B [System] is set to
“SD”2, and [SD Aspect] is set to “16:9”,
“Side Cut” in [A/V Set] B [Video Set] B [SD
Aspect] cannot be selected.
(A P151
[ System ] )
(
A P154 [ SD Aspect 2 ] )
Connecting a Remote
Control Unit
The switch
functions of the camera recorder can be
configured using the remote control unit.
* Remote control units supported: RM-LP25U,
RM-LP55U, RM-LP20G
o
Attaching Core Filter Beforehand v
Before using the remote control unit, attach the
core filter (small) to the remote cable of the
remote control unit.
.
Release the
stopper.
5 cm
Wind twice
To be connected to the camera recorder. [Core filter (small)]
1
Connect the remote control unit to the
camera recorder.
Connect the remote cable of the remote control
unit to the
[REMOTE] terminal.
.
REMOTE
Connect to the
Remote Control
Unit
Caution :
0
Turn off
the power of the camera recorder when
connecting a remote control unit.
2
Turn on the power of the camera recorder.
3
Set the operate switch of the remote control
unit to ON.
Precautions on Using the Remote Control Unit
0
When the switches of the camera recorder and
remote control unit are operated at the same
time, the switch operation of the remote control
unit takes priority over that of the camera
recorder.
0
Focus and zoom operations cannot be
performed using the remote control unit.
0
The shutter speed may vary slightly from the
value displayed on the camera recorder.
0
While
the
camera recorder is in the Media mode,
the Auto White Balance feature does not
function even if you operate it from the remote
control unit.
180
Connecting External Monitor
Connecting External Devices