INSTRUCTIONS
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
3
Set the time interval to start recording in
[Interval Rec].
To configure the setting, go to [System] B
[Record Set]
B [Rec Mode] B [Rec Interval].
(A P154 [ Rec Interval 1 ] )
4
Start recording.
0
Press the [REC]
button to record only the
number of frames specified in [Rec Frames]
and pause.
0
After the specified time in [Rec Interval] has
passed,
recording
starts again to record only
the number of frames specified in [Rec
Frames] and pause.
0
Interval Rec continues until the recording is
stopped.
The display changes (“STBYN” B “RRECN”
B “STBYN” (red text) B “RRECN” B
“STBYN” (red text)).
0
The
card
slot status indicator lights up in red.
5
Press the [REC] button.
0
The card slot status indicator lights up in
green.
0
The display becomes “STBYN”.
Caution :
0
Do not remove the SD card during recording
(RRECN, red
text) or recording pause (STBYN,
yellow text).
0
To remove the SD card during Interval Rec,
press the [CANCEL/RESET] button, check that
“STBYN” (white text) is displayed and the card
slot status indicator lights up in green before you
remove the card.
0
When the
[TC GEN] selection switch is set to “F-
RUN”, the time code will be recorded in “R-
RUN”.
0
Audio cannot be recorded. The audio level
meter is grayed out.
(A P162 [Audio Level Meter] )
Splitting the Clips Freely
(Clip Cutter Trig) 0
You can
split the clips freely without having to stop
recording during shooting.
1
Assign the “Clip Cutter Trig” function to
any of the user buttons.
(A P
45 [Assignment of Functions to User
Buttons] )
2
Press
the user button that is assigned with
“Clip Cutter Trig”
during shooting.
A clip cut icon (Q) appears on the display
screen for 3 seconds, and the clip is split.
.
100min
50min
282min
1
/60
F2.8
AE
±0
ND1
/64
12 :34 :56
ISO
102400
00: 00:00.00
1080 /30p
SDI IN
ITU709
COMPRESS
5 . 6 f t
B 5600
K
Memo :
0
Clips cannot be split again for a few seconds
after the operation is performed.
0
This item cannot be used when [
Slot Mode] is
set to “Backup”.
0
This item cannot be used when
[
Rec Mode] is
set to a value other than “Normal” or “Pre Rec”.
(A P154
[ Rec Mode 0 1 ] )
0
The split clips are recorded seamlessly without
interruptions in the video.
0
When Exchange
(U model) or MP4 (E model) is
selected, the clip cutter function cannot be used.
94
Special Recording 0
Shooting