User's Manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
Trimming Recorded Clips
You can
extract (trim) the necessary parts of a clip
recorded in the SD card.
The trimmed clip is saved as a new file on the same
SD card as the original clip. No changes are made
to the original clip.
1
Switch to Media mode.
Switch the mode using the [CAM/MEDIA]
selection button on the side control panel.
2
Move the cursor to the clip to be trimmed.
Move the cursor to the clip to be trimmed using
the cross-shaped button (JKH I).
.
2
3
Press the [USER4] button.
The action selection screen is displayed.
4
Select [Trim This Clip], and press the Set
button (R).
Playback of the selected clip starts.
.
0
30min
11:22:33.00
11:23:44.00
00:08: 22
282min
12 :34 : 56
Jan 24,2018
00:00: 00.00
1920x1080
30p 50M
1000/ 2000
TRIM
OUT
IN
Trim This Clip
Delete Clips...
FTP Upload...
Delete OK Mark...
Add OK Mark...
Deselect All
Select Range
A
B
C
4
A
Guide
Operation guide
B
Position bar
6
: Current position of the video
7
:
Position to start trimming (in point)
8
: Position to end trimming (out point)
C
Trimming information
W or Y : Indicates the available space in
the storage media (W
or Y)
7
: Indicates the time code of the in
point
8
: Indicates the time code of the out
point
9
: Indicates the duration from the in
point to the out point
Memo :
0
The
trimmed
clip will be saved to the same card
slot as that of the original clip.
0
[Duration] appears in yellow if the duration is 10
minutes or longer. Trimming cannot be
performed in this case.
0
When [System
] B [Record Set] B [Record
Format] B [WFrame Rate] is set to “
70M (XHQ)”2, [Duration] appears in
yellow if the duration is 6 minutes or longer.
Trimming cannot be performed in this case.
0
[Duration] appears in yellow if the duration is
longer than the recordable time on the storage
media. Trimming cannot be performed in this
case.
0
When trimming starts, the display switches to
the Media Display screen.
5
Specify the in point.
0
Operate
buttons
such as H/I or J/K to move
the video to the in point.
(A P98 [Playing back] )
0
Specify the in point by pressing the [USER1]
button at the point you want to start trimming.
6
Specify the out point.
0
Operate buttons
such as H/I or J/K to move
the video to the out point.
(A P98 [Playing back] )
0
Specify the out point by pressing the
[USER3] button at the point you want to end
trimming.
7
Perform trimming.
Press the [USER4] button to perform trimming.
Memo :
0
While trimming
is in progress, you can press the
[CANCEL/RESET] button to return to the
thumbnail screen.
0
When trimming the in and out point, the in point
trimmed may be up to one second before the
specified in
point and the out point trimmed may
be up to one second behind the specified out
point.
104
Trimming Recorded Clips
Playback