User's Manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
Lens REC
For selecting a function to be assigned to the
Record button (VTR button, etc.) on the lens.
A menu is displayed only when the FS-790 or
FS-900 is connected.
0
Intercom2:
Turns on/off the Intercom 2 connection.
0
Intercom1:
Turns on/off the Intercom 1 (intercom)
connection.
0
Rec:
Starts/stops recording.
[Setting Values: Intercom2, Intercom1, RRec]
Memo :
0
This function is available when it can be
assigned to
the Record button (VTR button, etc.)
on the lens in use.
0
Configure to “Intercom1” when configuring the
intercom with the FS-790 connected.
0
When the FS-900 or FS-790 is connected, the
functions of “Intercom1
” and “Intercom2” can
also be assigned to a user button.
User Switch Set...
For specifying user button related settings.
(A P111 [User Switch Set Item] )
Full Auto...
For configuring the Full Auto settings.
(A P115 [Full Auto Item] )
User Switch Set Item
USER0 to USER8, USER9J, USER10K,
USER11H, USER12I, USER13R (front),
USER1 (VF), USER2 (VF), LENS RET
The preconfigured function can be operated (on/
off, start, switch) by assigning one of the functions
in the following menu table to [
USER0], [USER1],
[USER2], [USER3], [USER4], [ONLINE/5],
[USER6], [USER7], [USER8], [J/9], [K/10], [H/11],
[I/12], front [SET/USER13] button, [RET] button
on the lens and the [USER1(VF)] and [USER2(VF)]
buttons on the viewfinder.
Set according to the shooting conditions. Usable in
the Camera mode.
(A P45 [Assignment of Functions to User
Buttons] )
Memo :
0
When a
viewfinder is connected, priority is given
to the [ZEBRA] switch of the viewfinder and the
user button that is assigned with the “Zebra”
function will not function.
0
“Focus Assist +” is a combination of the
“Focus
Assist” and “Expanded Focus
” functions.
0
“Skin Detail +
” is a combination of the
“Skin
Detail” and “Skin Area” functions.
0
The
[
SET/USER13] button at the front functions
as the [STATUS/SET] button in the factory
setting, but it can also be assigned with the
[USER13] function.
0
If “VF Display
” is assigned to the
[USER1(VF)]
or [USER2(VF)] button of the viewfinder, the
button can also be used in the Media mode.
Camera Function Menu
111
Menu Display and Detailed Settings