User's Manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
Display Type Item
This menu is used to set the displays on the LCD
monitor and viewfinder screen.
Battery
For setting the display of the remaining battery
power on the LCD monitor and viewfinder screen.
0
Time:
Displays the remaining battery power in
minutes. (min)
0
Capacity%:
Displays the remaining battery power in
percentage. (%)
0
Voltage:
Displays the current battery voltage in units of
0.1 V. (V)
[Setting Values: RTime, Capacity%, Voltage]
Memo :
0
The battery mark that appears before the “Time”,
“Capacity%” or “Voltage” value changes according to
the remaining battery power.
I
:
Battery which the capacity could not be
acquired
4
:
Below 13%
D
:
13% or higher
C
:
30% or higher
B
:
60% or higher
F
:
Battery communication error
J
:
Calibration required
0
While “Time” or “Capacity%” is displayed, “
E
”
appears when the level falls below the setting in
[System]
B
[Battery]
B
[Near End (%)]. Replace the
battery as soon as possible.
0
The remaining battery power and remaining time are
intended as reference values for the shooting
duration.
0
When the battery that is connected does not support
communication, the voltage is displayed regardless
of the setting.
Zoom
For setting the display method of the zoom
position.
0
Number:
Displays the zoom position in numbers (Z00 to
99).
0
Bar:
Displays the zoom position in a bar.
[Setting Values: Number, RBar]
Memo :
0
This item will not be displayed if the lens
attached does not support zoom position
information.
Focus
For setting the display method of the approximate
distance to the subject in focus during manual
focus.
0
Feet:
Displays the distance in feet.
0
Meter:
Displays the distance in meters.
[Setting Values: Feet, RMeter]
Memo :
0
This item will not be displayed if the lens
attached does not support focus position
information.
Shutter
For setting the shutter display to be displayed on
the LCD monitor and viewfinder screen.
0
DEG:
Displays the shutter speed in degrees in the
same way as film cameras.
0
SEC:
Displays the shutter speed in seconds.
[Setting Values: DEG, RSEC]
Memo :
0
“DEG” is selectable only when [WFrame Rate]
is set to “24p”
2 or “25p”. When [WFrame
Rate] is set to other values, the shutter display
setting is fixed at “SEC” and cannot be selected.
(A P152
[ W Frame Rate ] )
0
When a remote control unit is connected to the
[REMOTE]
terminal, “SEC” is displayed and
selection is disabled.
LCD/VF Menu
129
Menu Display and Detailed Settings