User's Manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
Return Input 0
For selecting the input destination of the return
video.
0
Network:
For inputting the return video from the
preconfigured network.
0
SDI:
Inputs return video from the [
HD/SD SDI IN]
terminal.
[Setting Values: Network, RSDI]
Return Aspect
For selecting the aspect ratio of the return video.
0
16:9:
Select this
option if the return video is a squeeze
signal.
0
4:3:
Select this option if the return video is a 4:3
aspect signal (including Letter Box).
[Setting Values: R16:9, 4:3]
Audio Set Item
Front Mic Select
For selecting the microphone to be connected to
the [MIC IN]
terminal.
0
Stereo M/S:
Selects the stereo M/S (Mid/Side) direct output
microphone.
0
Stereo L/R:
Selects the stereo L/R type microphone.
0
Mono:
Selects the monophonic microphone.
[Setting Values: Stereo M/S, RStereo L/R, Mono]
Memo :
0
When “Stereo M/S” is configured, use only
stereo M/S (Mid/Side) direct output
microphone.
Front Mic Power
Configure this setting when it is necessary to
supply +48 V power to the microphone that is
connected to the [MIC IN] terminal.
[Setting Values:
ROn, Off]
Memo :
0
When using a microphone that does not require
a +48V power supply, make sure that it is set to
the “Off” position before connecting the
microphone.
Front Mic 1 Ref.
For setting the reference input level when the
[AUDIO INPUT CH1]
or [AUDIO INPUT CH3]
selection switch is set to “FRONT”.
[Setting Values: -30dB, -40dB, R -50dB, -60dB]
Front Mic 2 Ref.
For setting the reference input level when the
[AUDIO INPUT CH2]
or [AUDIO INPUT CH4]
selection switch is set to “FRONT”.
[Setting Values: -30dB, -40dB, R -50dB, -60dB]
Rear Mic 1 Ref.
For configuring the reference input level when the
[AUDIO INPUT CH1]
or [AUDIO INPUT CH3]
selection switch is set to “REAR”, and the [AUDIO
INPUT1] selection switch to “MIC” or “MIC+48V”.
[Setting Values: -30dB, -40dB, -50dB, R -60dB]
Rear Mic 2 Ref.
For configuring the reference input level when the
[AUDIO INPUT CH2]
or [AUDIO INPUT CH4]
selection switch is set to “REAR”, and the [AUDIO
INPUT2] selection switch to “MIC” or “MIC+48V”.
[Setting Values: -30dB, -40dB, -50dB, R -60dB]
Rear Line Ref.
For configuring
the reference input level when one
of the [AUDIO INPUT CH1/CH2/CH3/CH4]
selection switches is set to “REAR”, and the
corresponding [AUDIO INPUT1/2] selection switch
is set to “LINE”.
[Setting Values: R+4dB, 0dB, -3dB]
A/V Set Menu
135
Menu Display and Detailed Settings