User's Manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
CH1 Audio Level/CH2 Audio Level/CH3
Audio Level/CH4 Audio Level
9
Front, Rear/Wireless
For configuring the method for adjusting volume
level when the
[MANUAL/AUTO] selection switch
of [AUDIO INPUT CH1 (/2/3/4)
] is set to
“MANUAL”.
0
Front + CH1(/2/3/4):
Adjust using the
[MIC LEVEL] knob on the front
and the [AUDIO INPUT CH1(/2/3/4)] recording
level adjustment knob.
0
CH1(/2/3/4) Knob:
Adjust using the [AUDIO INPUT CH1(/2/3/4)]
recording level adjustment knob.
0
Front Knob:
Adjust
using the [MIC LEVEL] knob on the front.
[Setting Values: Front + CH1(/2/3/4), CH1(/2/3/4)
Knob, Front Knob]
(Default setting: “Front Knob” for Front,
“CH1(/
2/3/4) Knob” for Rear/Wireless)
CH1/2 Audio Ref. Lv.
For setting the reference recording level of [CH1
]
and [CH2].
(Applies to both [CH1] and [CH2].)
[Setting Values: -12dB, -18dB, R-20dB]
CH3/4 Audio Ref. Lv.
For setting the reference recording level of [CH3
]
and [CH4].
(Applies to both [CH3] and [CH4].)
0
Ch1/2 -6 dB:
Sets to a value that is 6dB lower than that of
[CH1] and [CH2].
0
Ch1/2 -12 dB:
Sets to a value that is 12dB lower than that of
[CH1] and [CH2].
0
Ch1/2 Linked:
Sets to the same value as
[CH1] and [CH2
].
[Setting Values: Ch1/2 -6 dB, Ch1/2 -12 dB,
RCh1/2 Linked]
CH1/2 DRC..., CH3/4 DRC...
For configuring the individual parameters of DRC
(Dynamic Range Compression).
(A P72 [References on DRC (Dynamic Range
Compressor) and Limiter] )
9
Threshold Level
For configuring
the threshold of DRC for CH1/2 and
CH3/4.
[Setting Values: R -6dBFS, -9dBFS, -12dBFS,
-15dBFS, -17dBFS, Off]
9
Attack Time
For configuring
the time before DRC for CH1/2 and
CH3/4 operates.
[Setting Values: Fast, RMiddle, Slow]
9
Decay Time
For configuring
the time before the DRC operation
for CH1/2 and CH3/4 is canceled.
[Setting Values: Fast, RMiddle, Slow]
9
Mode
For configuring whether DRC for each channel
operates independently or in tandem with each
other.
([CH1] and [CH2], [CH3] and [CH4])
Select “Linked”
to link or “Separate
” to separate.
[Setting Values: Linked, RSeparate]
Limitter...
9
CH1(/2/3/4)
For
configuring
whether to enable limiter operation
for each channel.
0
On:
Enables limiter operation.
0
Off:
Disables limiter operation.
0
AUTO/MANUAL SW Set:
Operates according to the [AUDIO INPUT
MANUAL/AUTO] selection switch.
Operation is
“On
” in the AUTO mode and “Off”
in the MANUAL mode.
[Setting Values: On, Off, RAUTO/MANUAL SW
Set]
136
A/V Set Menu
Menu Display and Detailed Settings