User's Manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
Mic Wind Cut...
9
CH1(/2/3/4)
For configuring whether to cut the low-frequency
range
of
the audio signal when “FRONT” or “REAR”
is selected for [AUDIO INPUT] of each channel and
“MIC” or “MIC+48V” is selected for [AUDIO INPUT
1/2] at the back of the camera.
Set this item to reduce wind noise from the
microphone.
[Setting Values: On, ROff]
Memo :
0
When [Mic Wind Cut] is set to “On”, a icon
is displayed on the status screen (audio input)
while the function is operating.
Test Tone
For specifying whether to output the audio test
signals (1 kHz) during color bar output.
[Setting Values: On, ROff]
AUDIO OUT Ch.
For setting the channel to output to the [AUDIO
OUT] terminal.
0
CH3/4:
Outputs the audio of [CH3] and [CH4].
0
CH1/2:
Outputs the audio of [
CH1
] and [CH2].
0
MONI SEL SW Set:
Outputs according to the [MONI SELECT
]
switch setting.
[Setting Values: CH3/4, CH1/2, RMONI SEL SW
Set]
AUDIO OUT Ref.
For configuring the reference output level of the
[AUDIO OUT] terminal.
[Setting Values: +4dB,
R 0dB, -3dB]
AUDIO OUT Limiter
For configuring
whether to enable limiter operation
for the output of the [AUDIO OUT] terminal.
0
On:
Enables limiter operation.
0
Off:
Disables limiter operation.
[Setting Values: On, ROff]
Memo :
0
When [AUDIO OUT Limiter] is set to “On”, a
icon is displayed on the status screen (audio
output).
PHONE Output
For selecting whether to output audio from the
[PHONE] terminal
as stereo sound or mixed sound
when the [MONI SELECT] switch is set to “BOTH”.
0
Stereo:
Outputs stereo sound (outputs audio sound of
CH1(CH3) to L, and CH2(CH4) to R).
0
Mix:
Outputs mixed sound (mixed sound of
CH1(CH3) and CH2(CH4)) to both L and R.
[Setting Values: Stereo, RMix]
Min. ALARM Level
For configuring
whether to output or mute the alarm
sound when the [ALARM] volume adjustment knob
is turned to the minimum level.
[Setting Values: Audible, ROff]
Speaker Gain
For configuring the speaker gain.
[Setting Values: +6dB, +3dB, R0dB, -3dB, -6dB]
Wireless Channel
For configuring the wireless channels.
0
Dual:
Inputs the wireless Ch1 output to Ch1(Ch3)
Audio In and the wireless Ch2 output to
Ch2(Ch4) Audio In.
0
Single:
Inputs the wireless Ch1 output to both of
Ch1(Ch3)/Ch2(Ch4) Audio In.
[Setting Values: Dual, RSingle]
A/V Set Menu
137
Menu Display and Detailed Settings