User's Manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
P
Luminance Information
Displayed when the Spot Meter function is
activated.
MAX :
Maximum luminance
MIN : Minimum luminance
Q
Zebra pattern
During zebra pattern display,
(zebra icon)
is displayed on the display screen in Camera
mode.
(A P80 [Setting Zebra Pattern] )
R
Time Display
Displays the current time.
Memo :
0
The
date/time
display style can be configured in
[System] B [Date/Time].
0
When [System
] B [Record Set] B [Time
Stamp] is set to “On”, this item is not displayed.
S
Focus Display
Displays the approximate distance to the
subject in focus during manual focus.
Memo :
0
The displayed unit of measurement (feet or
meter) can
be configured in [LCD/VF] B [Display
Type] B [Focus].
0
This item may not be displayed depending on
the lens used.
T
Zoom Display
0
Displays the zoom position. (Zoom bar or
value)
.
0
The zoom bar will only be displayed for 3
seconds after the zoom operation is
activated.
0
The value will always be displayed. (Z00 to
99)
Memo :
0
The mode of display (value or bar) can be
configured in [LCD/VF]
B [Display Type] B
[Zoom].
0
This item may not be displayed depending on
the lens used.
U
Network Connection Icon
0
USB connection or built-in wireless LAN
connection u v
0
Set [Network
] B [Connection Setup] B
[USB/Int. WLAN] to “On”. u v
(A
P140 [ USB/Int. WLAN u v ] )
0
In the case of connecting to an external
network, check the destination in
[Network]
B [Connection Setup] B
[Default Gateway].
(A P140
[ Default Gateway ] )
Icon Status
.
Wireless LAN connection from the
host terminal (USB) is established
.
Wired LAN connection from the
host terminal (USB) is established
.
Cellular adapter connection from
the host terminal (USB) is
established
.
When a USB adapter different
from the connection settings is
detected
.
Built-in wireless LAN connection is
established
u v
(No
display)
0
When [USB/Int. WLAN] is set
to “Off”
u
v
0
When an unusable USB
adapter is detected
Memo :
0
The icon appears blinking when the camera
recorder is
starting up, and is displayed in yellow
while getting ready to connect.
0
LAN terminal connection
In the case of connecting to an external network,
check the destination in [Network]
B
[Connection Setup] B [Default Gateway].
Icon Status
.
LAN terminal connection is
established
(No
display)
When the LAN cable is not
connected
Memo :
0
The icon appears blinking when the camera
recorder is
starting up, and is displayed in yellow
while getting ready to connect.
164
Display Screen in Camera Mode
Display/Status Screen