User's Manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
IFB (Return Audio)0
Return audio from the network can be played
through a headphone.
Memo :
0
This feature
is only usable in the Camera mode.
0
Start the encoder before activating Return over
IP. To
end, turn off Return over IP before shutting
down the encoder.
0
This feature is available when [System] B
[Record Set] B [Record Format] B [System] is
set to “HD” or “SD”2. When [WFrame Rate]
is set to “24p”, this feature is not available.
Configuring the Return over IP Server
Configure the Return over IP settings and establish
the connection before displaying the return video.
1
Register the [Return Server].
Configure [Network] B [
Return over IP]
B
[Server] to “Server”.
Configure the individual settings in the [Return
Server] item.
Memo :
0
For details
on the registered information, please
consult the network administrator for the server.
0
Configure “Icecast” to [Type
].
Operates as IFB when the setting is configured
to “Icecast”.
Return Audio from the Network (IFB)
1
Set the camera recorder to the Camera
mode.
(A P20 [Operation Modes] )
2
Assign
the “Return over
IP” function to any
of the user buttons.
(A P45 [Assignment of Functions to User
Buttons] )
Memo :
0
The “Return over IP” feature can also be
operated using
“On”/“Off” under [Network] B
[Return over IP] B [Return over IP].
3
Configure the input destination of the
return video to “Network”
To specify the input destination of the return
video, configure [A/V Set]
B [Video Set
] B
[Return Input] to “Network”.
(A P135 [ Return Input 0 ] )
Memo :
0
When [System] B [Record Set] B [Record
Format]
B [System] is configured to “HD(SDI
In)” or “SD(SDI In)”2, “---” is displayed and
the setting cannot be configured.
4
Press the user button that is assigned with
the “Return over IP
”
function.
When Return over IP is activated, the settings
in [A/V Set] B [Audio Set
] B [IFB/RET Monitor]
will be applied to the audio.
(A P138 [ IFB/RET Monitor... 0 ] )
IFB (Return Audio)0
217
Connecting to the Network