User's Manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
Power Supply
To use this camera recorder, you can attach a
battery pack or connect an AC adapter to it.
(A P34 [Using a Battery Pack] )
(A P33 [Using AC Power (DC IN Power)] )
Caution :
0
Set the [
POWER ON/OFF] switch to “OFF”
before changing the power supply that operates
this camera recorder.
0
Use the camera recorder and peripheral
equipments within the rated output of the AC
adapter.
0
To connect other peripheral equipment, do so
under the following conditions.
0
Keep the total power consumption of the
peripheral equipments under 35 W when
using the recommended battery.
0
Keep the total power consumption of the
peripheral equipments under 65 W when
using Tandem 150 (recommended AC
adapter). u w
0
Keep the total power consumption of the
peripheral equipments under 50 W when
using AC-100 (recommended AC adapter).
x
0
The power
consumption of the [LIGHT] terminal
is below 50 W. Keep the total power
consumption of the peripheral equipments
excluding the [LIGHT] terminal under 35 W
when using the terminal. If the total power
consumption of the peripheral equipments
exceeds the rating, the power to the [LIGHT],
[DC OUT] (rear) and [DC OUT] (LAN) terminals
is automatically cut off. This is not a malfunction.
Use peripheral equipments with lower power
consumption then turn on the power of this
camera recorder again. u w x
0
To check the power consumption, refer to the
Power screen of the Status screen.
(A P171
[Power Screen] )
0
If the voltage of the [DC INPUT
] becomes 12 V
or less, the USB adapter connected to the
[HOST] terminal cannot be used. Check the
power supply and the peripheral equipments,
and turn on the power of this camera recorder
again.
0
Use
a
power supply of 12 V/ 2A or below for the
[LIGHT] terminal.
The [LIGHT] terminal, DC OUT terminal
(rear)/DC OUT (LAN) terminal and the D-tap
terminal of the battery loading folder cannot be
used at the same time. v
Using AC Power (DC IN Power)
Use the AC adapter (sold separately) to operate
the camera recorder with AC power.
Recommended AC Adapter
u w : Tandem 150 (Anton/Bauer)
v
:
IA-300a (IDX)
x
: AC-100 (IDX)
Memo :
0
For the type of AC adapter to be attached on a
battery mount,
check the method of attachment
in [Using a Battery Pack] (A P 34).
o
Attaching Core Filter Beforehand v
Attach the
core filter (large) to the DC cable of the
AC adapter before using the AC adapter.
.
Release the
stopper.
To be connected to the AC Adapter.
5 cm
Wind twice
1
Connect the DC cable of the AC adapter to
the [DC INPUT] terminal of the camera
recorder.
Check
that the power of this unit and that of the
AC adapter are both set to “OFF
”, followed by
connecting according to the diagram.
.
2
Turn on the power of the AC adapter,
followed by setting the [POWER ON/OFF]
switch of this unit to “ON”.
Power will be supplied to the camera recorder.
Caution :
0
Do not insert or remove the DC cable during
recording.
0
Do not use power supply of high voltage
fluctuation, containing noise such as ripple, or
with insufficient capacity.
Power Supply
33
Preparations