User's Manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
Viewing Recorded Videos
Immediately (Clip
Review)
You can check (review) the last recorded video clip
on the screen.
However, the video clip cannot be played back if
the settings of the camera recorder are different
from the video format (Resolution/Frame Rate/Bit
Rate/SD Aspect) of the clip.
(A P152 [ W Resolution ] )
(A P152 [ W Frame Rate ] )
(A P153 [ W Bit Rate ] )
(A P154 [ SD Aspect 2 ] )
Memo :
0
To use
this function, assign “Clip Review” to any
of the user buttons.
1
Press the user button assigned with the
“Clip Review”
function during standby
(“STBY” is displayed).
Playback of the configured section starts.
Memo :
0
The video clip is played back according to the
setting in [Camera Function] B [User Switch
Set] B [Clip Review]. By default setting (Last
5sec), the last 5 seconds of the clip is played
back.
(
A P113
[ Clip Review ] )
0
When playback is complete, the camera
recorder exits Clip Review and returns to
“STBY” (recording standby) mode.
Caution :
0
During Clip Review, only the [CANCEL/
RESET] and [REC] buttons are enabled.
Press the [CANCEL/RESET] button to cancel
clip review and return to “STBY” (recording
standby) mode.
Press
the [REC] button to cancel clip review and
enter recording mode. It will take some time to
start recording after the button is pressed.
0
When the last clip is less than 5 seconds, the
whole clip is played back.
0
Only
video
clips in the currently selected slot can
be reviewed.
0
When there
are no clips in the selected slot, Clip
Review function is disabled.
0
Clip Review is unavailable when Clip
Continuous Rec is paused (“STBYC”, yellow
text). To operate Clip Review, use the
[CANCEL/RESET] button to set to “STBYC”
(white text) first.
(A P91 [Clip Continuous Rec 0] )
0
Clip Review is unavailable when the camera
recorder is
connected to an external equipment
and the equipment is in recording state.
0
Clip Review is unavailable when operating View
Remote via network connection.
(A P202 [View Remote Control and Camera
Control Functions] )
0
Clip Review does not function during live
streaming.
0
Clip Review does not function while the record
trigger is in the REC state.
84
Viewing Recorded Videos Immediately (Clip Review)
Shooting