User's Manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Others
2
Set the number of frames to record in [Rec
Frames].
0
To configure the setting, go to
[System]
B
[Record Set] B [Rec Mode] B [Rec Frames].
(A P
154 [ Rec Frames 1
] )
3
Start recording.
0
Press the [REC] button to record only the
number of frames specified in [Rec Frames]
and pause.
0
The display changes (“STBYM” B “RRECM”
B “STBYM” (yellow text)).
0
The card slot status indicator lights up in
green.
4
Repeat Frame Rec.
0
Press the [REC]
button again to record only
the number of frames specified in [Rec
Frames] and pause.
0
The display changes (“STBYM” B “RRECM”
B “STBYM” (yellow text)).
0
Frame Rec continues until the recording is
stopped (step 5).
5
Press and hold the [REC] button.
0
The card slot status indicator lights up in
green.
Caution :
0
Do not remove the SD card during recording
(“RRECM”, red text) or recording pause
(“STBYM”, yellow text).
0
To remove
the SD card during Frame Rec, press
the [CANCEL/RESET] button, check that
“STBYM” (white text) is displayed and the card
slot status indicator lights up in green before you
remove the card.
0
When the
[TC GEN] selection switch is set to “F-
RUN”, the time code will be recorded in “R-
RUN”.
0
Audio cannot be recorded. The audio level
meter is grayed out.
(A P162 [Audio Level Meter] )
Interval Rec 1
In normal recording, when the recording stops, the
image and
accompanying data from the start till the
end of the recording are recorded as one “clip” on
the SD card.
In this mode, recording and pause are performed
repeatedly at the specified time interval. Only the
specified number of frames is recorded.
The recording can be written to the media as a
single clip until it is stopped.
Memo :
0
Audio will not be recorded.
0
Until a specified amount of recordings is
accumulated, the file will not be written to the
media.
0
After the
specified number of frames is recorded
and written to the media, recording will be
performed until the same number is
accumulated again.
0
If the specified amount is not reached when
recording is stopped, normal recording is
performed and frames are added to the ending
of the clip until the amount is reached. (Padding)
.
Specific amount of data
Actual clips recorded to the media
Records number of frames specified in [Rec Frames]
(Padding data)
Normal recording
PausePausePause
[Rec Interval][Rec Interval]
Recording resumes
Recording resumes
(Interval Rec stops)(Interval Rec starts)
Press [REC]Press [REC]
1
Set [Rec Mode] to “Interval Rec”.
0
Set [System] B [Record Set] B [Rec Mode]
to “Interval Rec”.
(
A P
154 [ Rec Interval 1 ] )
0
The display changes (“STBY”
B “STBYN”).
2
Set the number of frames to record in [Rec
Frames]
.
To configure the setting, go to [System] B
[
Record Set]
B [Rec Mode] B [Rec Frames].
(A P154 [ Rec Frames 1 ] )
Special Recording 0
93
Shooting