INSTRUCTIONS
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Focusing by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Monitoring Audio Sound During Recording Using a Headphone
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Setting Zebra Pattern
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Configuring Settings via a Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Logging in to Facebook
- Live Streaming on Facebook Live
- Logging in to YouTube
- Live Streaming on YouTube Live
- Broadcast Overlay
- Others
9
CH1 Limiter/CH2 Limiter
For specifying the
limiter settings for the CH1/CH2
audio input.
o
Threshold Level
For setting the value for activating the limiter.
[Setting Values: -9dBFS, R-6dBFS, Off]
o
Attack Time
For
setting the
response speed for activating the
limiter.
[Setting Values: Fast, RMiddle, Slow]
o
Decay Time
For setting the attenuation rate after the limiter
is activated.
[Setting Values: Fast, RMiddle, Slow]
Memo :
0
When [Limiter Mode] is set to “Link”, [CH2
Limiter]
cannot be specified.
0
If the channel specified is set to “AUTO”,
[Threshold Level] cannot be set to “Off”.
INPUT1 Mic Wind Cut/INPUT2 Mic Wind Cut
O
For selecting whether
to cut the low frequencies of
the audio input signals (low-cut) when the [AUDIO
INPUT INPUT1]/[AUDIO INPUT INPUT2] selection
switch is set to “MIC” or “MIC+48V”.
Set this item to reduce wind noise from the
microphone.
[Setting Values: On
, ROff]
Memo :
0
This item is
not displayed if the handle unit is not
connected.
Int. Mic Wind Cut
For selecting whether
to cut the low frequencies of
the audio input signals (low-cut) from the built-in
microphone. Set this item to “On” to reduce wind
noise from the microphone.
[Setting Values: On
, ROff]
Memo :
0
This item is enabled in the following cases.
0
When the [CH-1
] or [CH-2] selection switch is
set to “INT”. O
0
[CH1 INT] is
set to “Int. Mic L” or [CH2 INT] is
set to “Int. Mic R”.
(A P118 [ CH1 INT ] )
(A P118 [ CH2 INT ] )
Int. Mic Stereo Enhancer
For setting the enhancement level of the stereo
effect of the built-in microphone.
0
On
:
Enhances the stereo effect.
0
Off:
Does not enhance the stereo effect.
[Setting Values: ROn
, Off]
Memo :
0
This item is enabled in the following cases.
0
Both [CH-1] and [CH-2] selection switches
are set to “INT”.
O
0
[CH1 INT] is set to
“Int. Mic L” and [CH2 INT]
is set to “Int. Mic R”.
(A P118 [ CH1 INT ] )
(A P118 [ CH2 INT ] )
Monitor
For setting the
audio output from the [x] jack or the
speaker.
0
Stereo:
Outputs audio from [CH1] to L and audio from
[CH2] to R.
0
Mix:
Generates
a mixed
audio output from [CH1] and
[CH2].
0
CH1:
Outputs only the audio input from [CH1].
0
CH2:
Outputs only the audio input from [CH2].
[Setting Values: RStereo, Mix, CH1, CH2]
Memo :
0
If both [CH1] and [CH2] are input signals of the
built-in microphone, “Mix”
cannot be selected for
the output from the [x] jack.
0
“Stereo” cannot be selected for speaker output
in the Media mode.
120
A/V Set Menu
Menu Display and Detailed Settings