INSTRUCTIONS
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Focusing by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Monitoring Audio Sound During Recording Using a Headphone
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Setting Zebra Pattern
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Configuring Settings via a Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Logging in to Facebook
- Live Streaming on Facebook Live
- Logging in to YouTube
- Live Streaming on YouTube Live
- Broadcast Overlay
- Others
Setting Time Code
Generator
Presetting the Time Code
Time code and user’s bit data generated from the
internal time code generator are recorded.
This section describes how to set [TC/UB]
B [TC
Preset].
(A P111 [ TC Preset ] )
Memo :
0
When [System] B
[Record Set] B [Record
Format] B [WFrame Rate] is set to “50p”, “50i”
or “24p”, setting for “Drop” will be disabled.
(A P124
[ W Frame Rate ] )
0
You can configure
the setting without accessing
the [TC/UB] menu screen.
(A P74 [Setting Time Code without Opening
the Menu] )
Required Settings Before Preset
1
Set [TC/UB] B [
TC Generator
]
to “Rec Run”
or “Free Run”.
(A P111 [ TC Generator ] )
0
[Rec Run]:
Preset data in the time code generator
operates
in
run mode during recording mode.
Set this when recording continuous time
code in connecting frames.
0
[Free Run]:
Time code starts to operate in run mode from
the preset time in the time code generator.
2
Select the framing mode for the time code
generator (only when
the frame rate setting
is “60” or “30”).
To configure the setting, go to [TC/UB] B
[Drop
Frame].
(A P111 [ Drop Frame ] )
0
[Drop]:
Sets
the run
mode of the time code generator
to drop frame mode. Use this setting when
placing emphasis on the recording time.
0
[Non Drop]:
Sets the run mode of the time code generator
to non-drop frame mode. Use this setting
when placing emphasis on the number of
frames.
Memo :
Drop frame/non-drop frame mode
0
When [System] B [Record Set] B [Record
Format] B [Frame Rate
] is set to
“60p”, “60i”, or
“30p”, the actual number of frames per second
is approximately 59.94 (29.97). However, the
time code processing standard is “60p”, “60i”, or
“30p” frames. To make up for the frame number
discrepancy, the drop frame mode (Drop) drops
the 00 frame and 01 frame every minute except
for minutes that are multiples of 10. However, in
the case of “60p”, the 00, 01, 02 and 03 frame
are dropped.
0
The
non-drop frame
mode (Non Drop) does not
drop frames and ignores the discrepancy with
the actual time.
Setting Time Code
.
Setting Time Code Generator
73
Shooting