User Manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Focusing by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Monitoring Audio Sound During Recording Using a Headphone
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing Time Code on Another Camera
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Splitting the Clips Freely (Clip Cutter Trig)
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
Camera Function Menu
Menu screen for specifying operation settings
during shooting.
This item can only be selected in the Camera
mode.
Bars
For setting whether to output color bars.
[Setting Values: On, ROff]
Memo :
0
The audio test signals (1 kHz) can be output
simultaneously with the color bar output.
(A P114
[ Test Tone ] )
OIS
For setting whether to enable image stabilizer.
When “On
” is selected, set the Level.
[Setting Values: On, ROff]
9
Level
For setting the level of the image stabilizer.
[Setting Values: High, RNormal]
Memo :
0
When “High” is selected, correcting severe
camera shake may cause the area surrounding
the image to darken.
Flicker Correction
For setting whether to adjust image flicker that
occurs under a fluorescent light.
[Setting Values: On, ROff]
Flash Band Correction
For reducing the condition of the flash band
phenomenon, which creates an unnatural image
with a part of it brightly lit, such as by the camera
flash of another still camera.
[Setting Values: On, ROff]
Caution :
0
Flash
band correction function is not available in
any of the following cases.
0
When [Rec Mode] is set to “Variable Frame”
0
When [WFrame & Bit Rate]/[YFrame & Bit
Rate] is set to
“24p”
0
When
in the Automatic Shutter mode or when
the shutter is turned on in the Manual Shutter
mode
(A P56 [Manual Shutter Mode (Manual Shutter
Switching)] )
0
When [Network] is set to “On(SDI Off)” or
“On(HDMI Off)”
0
[Flash Band Correction]
operates when the
luminance of the screen varies widely, with or
without flash light. However, depending on the
shooting condition, the flash band correction
may not be fully effective even if there are flash
lights.
0
The following symptoms may occur under flash
light,
but these are not malfunctions due to flash
band correction.
0
Moving object appears to be stationary
momentarily.
0
A horizontal line appears on the image.
0
The [Flash Band Correction] function will be set
to “Off” if the camera recorder switches from the
Camera mode to another mode, or when the
[POWER ON/OFF(CHG)] switch is set to
“OFF(CHG)”.
Shutter
For specifying shutter-related settings.
Use this item to set to
“Step” (fixed value) or
“Variable” when operating with the cross-shaped
button (JK) on the right side.
0
Variable:
Sets to variable scan. Use this setting such as
when shooting a PC monitor.
0
Step:
Sets to step shutter, which switches the shutter
speed by a fixed value.
[Setting Values: Variable, RStep]
AE Level
For setting the convergence level during AE (Auto
Exposure).
This can also be adjusted using the cross-shaped
button (HI) on the right side.
[Setting Values: -6 to +6 (R0)]
AE Speed
For
setting the convergence speed during AE (Auto
Exposure).
[Setting Values: RFast, Middle, Slow]
98
Menu Display and Detailed Settings