User manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Focusing by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Monitoring Audio Sound During Recording Using a Headphone
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing Time Code on Another Camera
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Splitting the Clips Freely (Clip Cutter Trig)
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
Monitor
For setting the audio sound of the [x] terminal to
stereo or mixed sound when the [MONITOR]
switch on the LCD monitor is set to
“BOTH”.
0
Mix:
Outputs
mixed sound (mixed sound of CH1 and
CH2) to both L and R.
0
Stereo:
Outputs stereo sound (outputs audio sound of
CH1 to L, and CH2 to R).
[Setting Values: RMix, Stereo]
Memo :
0
If both CH1 and CH2 are built-in microphones,
stereo sound is output from the [x] terminal
regardless of the
[Monitor] setting.
Alarm Level
For selecting whether to turn on the warning tone
as well as setting the volume.
The warning tone is output from the monitor
speaker or [x] terminal.
[Setting Values: RHigh, Middle, Low, Off]
Audio On FULL AUTO
For setting whether to enable Auto for audio when
[FULL AUTO] is set to “ON”.
0
SW Set:
Sets the audio recording mode following the
[
CH1/CH2 AUTO/MANUAL] selection switch
setting.
0
Auto:
Sets audio recording mode to the forced auto
mode.
[Setting Values: SW Set, RAuto]
System Menu
This menu screen allows system-related settings.
For specifying recording settings, formatting and
restoring of SD card, tally lamp settings, network
settings, date/time, time zone, and other settings.
It can also be used to reset the menu settings to
their default values.
Record Set...
For specifying recorded video-related settings.
(A P117
[Record Set Item] )
Media
9
Format Media
For formatting (initializing) an SD card.
Select a card slot (A or B), select
[Format] from
[Cancel]/[Format], and press the Set button (R) to
format (initialize) the card.
(A P41 [Formatting (Initializing) SD Cards] )
9
Restore Media
For restoring an SD card.
Select
a card slot (A or B), and press the Set button
(R) to restore the SD card.
(A P42 [Restoring the SD Card] )
Memo :
0
This
item appears only when the SD card needs
to be restored. However, it is not selectable
when recording in Camera mode and during Clip
Review.
Setup File
This allows you to save the menu settings as well
as the performance results of shutter speed and
AWB.
It is useful to save settings according to different
shooting conditions.
9
Load File...
Loads the settings.
(A P
144 [Loading a Setup File] )
9
Store File...
Saves the settings.
(A P
143 [Saving Setup Files] )
9
Delete File...
Deletes the configured file.
(A P
144 [Deleting Setup Files] )
115
Menu Display and Detailed Settings