User manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Focusing by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Monitoring Audio Sound During Recording Using a Headphone
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing Time Code on Another Camera
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Splitting the Clips Freely (Clip Cutter Trig)
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
List of Live Streaming Error Displays a
The following error messages are displayed when the live streaming setting is incorrect, or when the
connection is lost during live streaming.
Error message Status Action
Invalid Address
0
The IP address format is
incorrect.
0
The domain name cannot be
converted into the IP address.
0
Enter the IP address or host
name of the destination
correctly.
(A P176
[Setting Distribution] )
Multicast Is Not Supported An IP multicast address was set. Use an IP address that is not a
multicast address.
Cannot Connect to Receiver Establishment of connection with
TCP failed.
0
Ensure that the recipient’s
device is set to TCP.
0
Set Type to
“MPEG2-TS/UDP”.
(A
P176 [Setting Distribution] )
TCP Disconnected TCP connection is lost. Check to ensure that there is no
abnormality in the decoder, or
network connection device and
cables,
followed by establishing the
connection again.
Not Enough Bandwidth
0
The communication bandwidth
is narrower than the average bit
rate.
0
The network bandwidth is
insufficient, and packets are
discarded.
0
Lower the resolution/picture
quality of the video to be
distributed.
0
Consider
switching to the use of
a stable network, such as wired
LAN.
Connection Timeout Timeout for connection via ZIXI. Set [Destination Address] and
[Destination Port
] correctly.
(A P176 [Setting Distribution] )
Authorization Failed Authentication of connection via
ZIXI failed.
Set [Stream ID] and [Password]
correctly.
(A P
176 [Setting Distribution] )
Connection Error Connection via “ZIXI” or “RTMP”
failed.
Check whether a different camera
with an identical stream ID is
connected.
0
Set [Destination URL] and
[Stream Key] correctly.
(A P123
[ Destination URL ] )
(A P123 [ Stream Key ] )
Disconnected “ZIXI” or “RTMP” connection is lost. Check whether there is abnormality
with
the network connection device,
cables, etc., and try to re-establish
the connection.
Blinking of the Tally Lamp
The tally lamp start blinking when the remaining space on the SD card is running out during recording, or
when the battery power is running low.
Blinking Mode Remaining Battery Power/SD Card Space
Blinks slowly
(once every second)
0
Battery power is low
0
Remaining recording time on SD card is less than 3 minutes (during
recording)
0
When a malfunction occurred during live streaming a
Blinks quickly
(2 times per second)
0
Remaining battery power is almost zero
0
Remaining recording time on SD card is zero (during recording)
0
Error on the camera recorder
181
Others