User Manual
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Monitor Speaker
- Adjusting Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- SD Card
- About the Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting a Recording Format
- Zoom Operation
- Focus Operation
- Adjusting the Focus by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Connecting External Devices
- Managing/Editing Clips on a PC
- Connecting External Monitor
- Connecting a Earphone
- Connecting Wired Remote Control
- Connecting a Remote Control Unit
- Functions Operable from the Remote Control Unit
- Inputting SDI Signals from an External Device
- Inputting External Synchronizing Signals (Genlock)
- Displaying Return Videos from an External Device
- Studio System
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
Blinking of the Tally Lamp
The tally lamp start blinking when the remaining space on the SD card is running out during recording, or
when the battery power is running low.
(Common for front and back tally lamps)
Blinking Mode Remaining Battery Power/SD Card Space
Blinks slowly
(once every second)
0
Battery power is low
0
Remaining recording time on SD card is less than 3 minutes (during
recording)
0
When a malfunction occurred during live streaming
Blinks quickly
(2 times per second)
0
Remaining battery power is almost zero
0
Remaining recording time on SD card is zero (during recording)
0
Error on the camera recorder
Warning Tone
0
Warning tone is output from the monitor speaker and [PHONES] terminal when the battery level is low.
0
Warning tone is also output when an error occurs in the camera recorder.
Memo :
0
You can specify whether to turn on the warning tone as well as setting the volume in [A/V Set] B [Audio
Set] B [Alarm Level].
(A P129 [ Alarm Level ] )
Troubleshooting
Symptom Action
Power does not turn on.
0
Is the power supply or battery properly connected?
0
Is the battery charged?
0
Is the power turned on immediately after it is turned off?
Make sure to wait for an interval of at least 5 seconds before turning
on the power again.
Unable to start recording.
0
Is the record trigger button/lock switch on the handle turned on?
0
Is the write-protect switch of the SD card turned on?
Make sure that the write-protect switch is turned off.
(A P43 [Write-Protect Switch on the SD Card] )
0
Is the camera recorder set to the Camera mode?
Press the [CAM/MEDIA] selection button to switch to the Camera
mode.
(A P18 [Operation Modes] )
Camera image is not output on
the LCD monitor and
viewfinder screen.
0
Is the camera recorder set to the Camera mode?
Press the [CAM/MEDIA] selection button to switch to the Camera
mode.
(A P18 [Operation Modes] )
Playback does not start after
selecting a clip thumbnail and
pressing the Set button (R).
0
Is the selected clip a playable clip?
Playback is not possible if the clip has a different video format setting.
206
Error Messages and Actions
Others