User Manual
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Monitor Speaker
- Adjusting Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- SD Card
- About the Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting a Recording Format
- Zoom Operation
- Focus Operation
- Adjusting the Focus by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Connecting External Devices
- Managing/Editing Clips on a PC
- Connecting External Monitor
- Connecting a Earphone
- Connecting Wired Remote Control
- Connecting a Remote Control Unit
- Functions Operable from the Remote Control Unit
- Inputting SDI Signals from an External Device
- Inputting External Synchronizing Signals (Genlock)
- Displaying Return Videos from an External Device
- Studio System
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
Return Input A B
For selecting the input destination of the return
video.
0
SDI:
Inputs return video from the [HD/SD SDI IN]
terminal on the side.
0
Adapter:
Inputs return video from the adapter connected
to the accessory connection terminal (68 pins)
on the rear of the camera recorder.
0
Studio:
Inputs return video from studio adapter
connected to the [STUDIO] terminal on the side.
[Setting Values: SDI, RAdapter, Studio]
Memo :
0
If this item is set to “SDI”, the setting for [Camera
Function] B [User Switch Set] B [Return
Video] is fixed at “Camera R Return”.
Return Aspect A B
For selecting the aspect ratio of the return video.
0
16:9:
Select this option if the return video is a squeeze
signal.
0
4:3:
Select this option if the return video is a 4:3
aspect signal (including Letter Box).
[Setting Values: R16:9, 4:3]
Audio Set Item
Input1 Mic Ref.
For setting the reference input level when the
[INPUT1] selection switch is set to “MIC” or “MIC
+48V”.
[Setting Values: -60dB, R -50dB, -40dB, -30dB]
Input2 Mic Ref.
For setting the reference input level when the
[INPUT2] selection switch is set to “MIC” or “MIC
+48V”.
[Setting Values: -60dB, R -50dB, -40dB, -30dB]
AUX Gain
For setting the sensitivity of the [AUX] input
terminal.
[Setting Values: +12dB, +6dB, R0dB, -6dB, -12dB]
CH3/4 Input Level
For setting the mode and level of input to [CH-3]
and [CH-4].
(A P71 [For CH-3/CH-4] )
Memo :
0
Selection is disabled if [System] B [Record
Set] B [Record Format] B [WAudio]/[YAudio] is
set to “2ch”.
(A P133 [ W Audio ] )
(A P134 [ Y Audio ] )
CH1/2 Ref. Level
For setting the reference recording level of [CH-1]
and [CH-2]. (Applies to both [CH-1] and [CH-2].)
[Setting Values: -12dB, -18dB, R-20dB]
CH3/4 Ref. Level
For setting the reference recording level of [CH-3]
and [CH-4]. (Applies to both [CH-3] and [CH-4].)
0
CH1/2 -12dB:
Sets to a value that is 12dB lower than that of
[CH-1] and [CH-2].
0
CH1/2 -6dB:
Sets to a value that is 6dB lower than that of
[CH-1] and [CH-2].
0
CH1/2 Link:
Sets to the same value as [CH-1] and [CH-2].
[Setting Values: CH1/2 -12dB, CH1/2 -6dB,
RCH1/2 Link]
A/V Set Menu
127
Menu Display and Detailed Settings