User Manual
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Monitor Speaker
- Adjusting Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- SD Card
- About the Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting a Recording Format
- Zoom Operation
- Focus Operation
- Adjusting the Focus by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Connecting External Devices
- Managing/Editing Clips on a PC
- Connecting External Monitor
- Connecting a Earphone
- Connecting Wired Remote Control
- Connecting a Remote Control Unit
- Functions Operable from the Remote Control Unit
- Inputting SDI Signals from an External Device
- Inputting External Synchronizing Signals (Genlock)
- Displaying Return Videos from an External Device
- Studio System
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
9
Type
For setting the system to transfer videos for
distribution.
[Setting Values: RMPEG2-TS/UDP, MPEG2-TS/
TCP, RTSP/RTP, ZIXI]
Memo :
0
Use reception devices that are compatible with
the respective transfer systems.
0
To use the “ZIXI” setting, a dedicated server is
needed separately.
9
UDP/TCP Settings
For specifying the settings that are enabled only
when [Type] is set to “MPEG2-TS/UDP” or
“MPEG2-TS/TCP”.
Memo :
0
The settings cannot be changed during live
streaming.
o Destination Address
For setting details such as the host name and the
IP address of the live distribution destination.
* Enter not more than 127 characters using single-
byte alphanumeric characters (a to z, 0 to 9),
single-byte hyphen [-], or dot [.].
o Destination Port
Enter the network port number of the live
distribution destination using an integer between 1
and 65535.
The default value is 6504.
9
RTSP/RTP Settings
For specifying the settings that are enabled only
when [Type] is set to “RTSP/RTP”.
Memo :
0
The settings cannot be changed during live
streaming.
o Password
Changes the password for RTSP authentication to
enable client access. The current password is
displayed. Enter a new password directly.
There is no default value (blank).
* Enter not more than 31 characters.
9
ZIXI Settings
For specifying the settings that are enabled only
when [Type] is set to “ZIXI”.
Memo :
0
The settings cannot be changed during live
streaming.
o Destination Address
For setting details such as the host name and the
IP address of the live distribution destination.
* Enter not more than 127 characters using single-
byte alphanumeric characters (a to z, 0 to 9),
single-byte hyphen [-], or dot [.].
o Destination Port
Enter the network port number of the live
distribution destination using an integer between 1
and 65535.
The default value is 2088.
o Stream ID
For setting the registered stream ID of the live
distribution destination.
The default value varies with the product model.
* Enter not more than 63 characters.
o Password
For setting the [Stream ID] password.
There is no default value (blank).
* Enter not more than 127 characters.
o Latency
For setting the latency mode.
[Setting Values: Medium, RLow]
Connection Setup
For specifying the settings for connecting to the
network.
A [Wizard] screen will appear according to the
adapter connected to the rear [HOST] terminal.
Follow the instructions to perform the setting.
You can Store, Load, and Delete the settings
specified on the [Wizard] screen.
9
Wizard
A [Wizard] appears according to the adapter
connected to the rear [HOST] terminal.
Follow the instructions on the screen to perform
setting.
9
Load
Loads the settings on the [Wizard] screen.
(A P198 [Reading the Connection Settings
File] )
9
Store
Saves the settings on the [Wizard] screen.
(A P197 [Saving the Connection Settings File] )
9
Delete
Deletes the saved settings.
(A P199 [Deleting Connection Settings] )
System Menu
139
Menu Display and Detailed Settings